Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs

See what our Experts say about this Convert-A-Ball Trailer Hitch Ball Mount

• Recommended Hitch Extender for Towing with a 2008 Range Rover
  Since hitch extenders like the 11" Roadmaster # RM-071 you show in your pictures reduces the weight rating of the hitch by 50% we typically recommend avoiding them as a solution. For your application we have ball mounts with extended shanks that don't reduce the weight capacity of your hitch and that's what I recommend going with. For a long ball mount we have the Brophy Ball Mount # BM20 which has a 3/4" rise/2" drop and measures 13-1/4" from the center of the hitch pin hole to center...
  view full answer...
  
• Accounting for Tow Vehicle Sag when Choosing Ball Mount
  Choosing a ball mount with the proper rise or drop is not an exact science. I typically recommend allowing for 1 to 2 inches for sag once the trailer is coupled. This figure can increase of decrease depending on the trailer tongue weight and the nature and condition of the tow vehicle suspension. Having the trailer coupler a bit on the high side of level is preferable to having it below level. In your case, having a late-model pickup truck as the tow vehicle that is towing a trailer with...
  view full answer...
• Trailer Hitch Recommendation for 2017 Subaru Outback Wagon
  For your 2017 Subaru Outback Wagon the Draw Tite hitch part # 75673 is a confirmed fit and would be a great choice. This is a 2-inch hitch which is the most popular hitch size for accessories and has the best capacities. For trailer wiring the part # 118467 would also be the correct kit to get. The Convert-A-Ball ball mount # AMSC2 would work too if you needed a 2-inch drop. You will also need a product like part # PC3, part # e98880, or part # 63232 to secure the accessory in your 2"...
  view full answer...
• Cushioned Ball Mount Recommendation with 1-1/4 inch Diameter Hitch Ball Hole
  Sounds like you are looking for the part # AMSC2HD. This is the higher rated version of the part # AMSC2 which has a 14k capacity and a ball hole diameter of 1-1/4 inch.
  view full answer...
• Towing Capacity of 2012 GMC Terrain
  According to the information contained in the owner's manual beginning on page 9-56 of the owner's manual, the tow capacity of the VEHICLE will depend on the engine size and whether or not the vehicle has brakes. Terrain models with the 2.4 L engine can tow up to 1500 lbs and with the 3.0 L, up to 3500 lbs. GMC states that if the trailer doesn't have brakes, the capacity is reduced to 1000 lbs. The capacity of the HITCH itself should be listed on a sticker affixed to the hitch, which would...
  view full answer...
• Recommend Hitch That Will Fit My 1990 Jeep Wrangler YJ
  I do have a hitch that will fit your 1990 Jeep Wrangler YJ, but the item you selected, Draw-Tite Trailer Hitch, part # 75054 will not fit. For a Class III 2 Inch hitch like part # 75054, for your Jeep, you will need the Curt Trailer Hitch, part # 13657. The Draw-Tite hitch # 75054 that you selected is designed to fit 1984-2001 Jeep Cherokee, and the 1984 Jeep Wagoneer Downsize. To complete your towing setup you will need the following items: Ball Mount, part # AMSC2 1-7/8 Inch Hitch...
  view full answer...
• Does Bumper Fascia of 2013 Inifiniti JX35 Need to Be Modified to Install a Hitch
  Whether you'll need to modify the bumper fascia or not will depend on which hitch you choose. The nice thing about the Curt Class III you mentioned, part # C13126 is that the entire hitch with the exception of the receiver opening is concealed behind the vehicle bumper. According to the installation instructions, a small (1-3/8 x 2-1/2 inch) area of the underside of the bumper fascia would need to be trimmed away. I've linked you to photos showing the area that would be trimmed and how...
  view full answer...
  
• Can the eTrailer Ball Mount Kit Be Ordered with a Locking Hitch Pin
  The Ball Mount Kit part # 989900 does not come with a locking hitch pin. That said, if you didn't want any extra parts you can purchase each of the components in the Ball Mount Kit separately which I have listed out for you below. Draw-Tite Ball Mount 2" Drop part # AMSC2 Draw-Tite Ball Mount 4" Drop part # 2753 1-7/8" Hitch Ball part # 19260 2" Hitch Ball part # 63845 etrailer Ball Mount Bag part # ETBMB
  view full answer...
• 2 inch Hitch Ball Mount Recommendation with 2 inch Drop
  The Convert-A-Ball ball mount part # AMSC2 has the same 2 inch drop as the Curt you referenced and it does not have a hitch ball that comes with it or a pin so it would be your best solution.
  view full answer...
• Parts Needed to Install Hitch, Brake Controller, 7 Way and 4 Way on a 2002 Chevrolet Express Van
  First we will start off with the hitch. I recommend going with the Curt Class III Receiver Hitch, # 13040, for your 2002 Chevrolet Express Van. This hitch receiver bolts directly to the frame of the van with no welding or drilling required. For a t-connector we have the T-One Wiring Harness, # 118377, that plugs directly into your existing taillight wiring without any cutting or splicing. In order to obtain a 7 way at the back of the van, you will need to install a Universal Installation...
  view full answer...
• Can Curt or EcoHitch Class III Hitches for 2021 Subaru Forester Serve as Towing/Recovery Points
  Absolutely! In many instances on vehicles where there's a tow hook bolted to the underside of the vehicle, a hitch installation would require that they be removed. Even though that's not the case with your vehicle, the situation is common enough that Curt and EcoHitch purposely design their hitches knowing that they might need to be used as a recovery point at some future time. Both the Curt # C47HR and the EcoHitch # 306-X7391 hitches are built strong enough that they can be used as...
  view full answer...
• Recommened Trailer Hitch 1999 Ford Explorer Sport 2 Door
  The Draw-Tite Class III hitch you referred to, part # 75083 is indeed a fit for the 1999 Ford Explorer Sport. However, it wouldn't be compatible with vehicles that have a spare tire that uses a 16 inch wheel. If your spare has a 16 inch wheel, use the Draw-Tite # 75096. If you'll be towing with your Explorer Sport, you might be interested in the following parts to complete your towing system: Trailer wiring harness with 4-pole trailer connector, part # 118345 Ball mount, part # AMSC2 1-7/8...
  view full answer...
• Will the Draw-Tite Hitch # 75210 fit a 2006 Dodge Sprinter with a Factory Step Bumper
  The Draw-Tite Class III 2 Inch Hitch, part # 75210, is for a 2006 Dodge Sprinter with a 140 inch or 158 inch wheelbase and either single or dual rear wheels. It will not fit the 118 inch wheelbase vehicle. To fit the Sprinter with the dual rear wheels the width between the frame rails will need to measure 35-1/4 inches. On the 2006 Dodge Sprinter, the Draw-Tite hitch # 75210 will fit if you have the factory bumper that is molded to match the design of the vehicle. It will not fit your...
  view full answer...
• Curt RockerBall and Convert-A-Ball Compatibility With A 5,000LB Boat Trailer
  The Curt RockerBall Shock Absorbing 2" Hitch Ball # C40047 cannot be used with a shock absorbing ball mount like the Convert-A-Ball Ball Mount # AMSC2. It can also not recommend by Curt to be used with surge brake couplers. I recommend using a standard style ball mount with a anti rattle hitch pin for a trailer that does not have a surge brake coupler. This can be found in a kit like the Curt RockerBall Anti-Rattle Towing Kit # C63KR. Remember that the RockerBall adds 1-1/2" to your receiver...
  view full answer...
• How Thick Is The Metal Where Hitch Ball Installs On Convert-A-Ball Ball Mount AMSC2?
  Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs # AMSC2 is 3/4" thick where the ball mounts to the ball mount as shown in the included diagram.
  view full answer...
  
• How to Choose the Correct Ball Mount for 2003 Chevy Pulling Fish Shack
  In order to choose the correct ball mount, there are a couple measurements you'll need to take. First, make sure both your Chevy and trailer are parked on level ground; you'll then want to measure from the ground to the top of your hitch receiver. Next, measure from the ground to the bottom of your coupler. If the height of your hitch is greater, you will need a ball mount with that amount of drop. If the height of the coupler is greater, you'll need a ball mount with that amount of rise....
  view full answer...
• Recommended Hitch for 2014 Volkswagen Tiguan That Does Not Require Stabilizing Strap 18050
  Many Curt brand hitches do carry the warranty requirement to use a strap like # 18050 when any non-wheeled load is installed in the hitch, such as a bike rack or cargo carrier. This applies both to their 1-1/4-inch Class II hitch # C12097 and their 2-inch Class III hitch # C13133. The strap can be positioned at the top of the rear hatch, or on other vehicles to one of the raised roof side rails or roof rack crossbars. Since use of the strap can be a nuisance for some folks, I suggest choosing...
  view full answer...
• Is There a Convert-A-Ball Interchangeable Ball With 2-5/16" & 2" Hitch Balls And 1-1/4" Shaft
  Hello Jeff, There is not a Convert-A-Ball interchangeable ball set with a 1-1/4" shank as well as 2-5/16" and 2" hitch balls. The thickest shank for that set up is the 1" shank of the Convert-A-Ball Interchangeable Ball Set # 906b. You can still use this if you're ok with going to a new ball mount with a 1" hitch ball hole diameter like the 3/4" Rise, 2" Drop Convert-A-Ball # AMSC2. I've added a link below to our entire selection of ball mounts with a 1" hole diameter if you'd like to...
  view full answer...
• Trailer Hitch Recommendation for 2015 Subaru Legacy with Good Ground Clearance
  We haven't tested our hitches on the 2015 Subaru Legacy, but we have tested them on 2011 Legacy. The Class III hitch that I would recommend the Draw-Tite trailer hitch # 75673 has 10 inches of clearance from receiver to ground. This should provide plenty of clearance so you will not bottom out when towing. Since you'll be using the hitch for towing purposes, you'll need to see your dealer for a wiring harness. You'll also need the following to complete your towing system: Ball Mount,...
  view full answer...
• Convert-A-Ball Interchangeable Ball Set 902B Ball Mount Compatibility
  The Convert-A-Ball Interchangeable Ball Set # 902B can install on any class of ball mount that has a 1-inch diameter ball hole and whose ball platform is not too thick for the shank which is 2-1/4-inches long. This multi-ball part will fit properly on a ball platform up to 1-1/8-inches thick. I confirmed this with Convert-A-Ball. This item is rated for 10,000-lbs towing no matter which ball size is installed. For example, the Convert-A-Ball Ball Mount Class IV Ball Mount # AMSC2 has a...
  view full answer...
• Lowering Exhaust to Install Hitch on 2008 Mitsubishi Outlander
  All three of the hitches offered for your 2008 Outlander would require that the exhaust be lowered to provide access to the attachment points in the frame. Our installers routinely use a ratchet strap to provide support to the exhaust once it is removed from the exhaust hangers. The purpose of the strap is to control the descent of the exhaust so it does not fall too rapidly and damage something. The exhaust hangers are very easy to remove, simply spray the metal hanger that passes through...
  view full answer...
• Can A Convert-A-Ball Cushioned Ball Mount Be Used With A Curt RockerBall?
  Though the Convert-A-Ball # AMSC2 cushioned ball mount and the Curt RockerBall, like the # C40047, are very nice products and will help with chucking and vibrations, they cannot be used together. You are correct in that they will help with the same issues, but may actually end up causing more problems than counteracting them when used together. With that being said, either of these are great options, but it should be noted that the RockerBall hitch balls will sit 1-1/2" higher than a standard...
  view full answer...
• Can The Convert-A-Ball Ball Mount Be Used In A Gen-Y Rebel Stacked Receiver
  Physically the Convert-A-Ball Ball Mount for 2" Hitches # AMSC2 would fit into various Gen-Y Rebel stacked receivers, but Gen-Y only recommends using their own ball mounts to avoid any issues with capacity. The # AMSC2 would sit so far out of the receiver that you're now adding more leverage and lessening the capacity to an unknown number. If you look at any Rebel stacked receiver, such as the # GY92FR, you'll notice that the shank they use is much shorter than a traditional ball mount...
  view full answer...
• Fit of etrailer Brand e98844 Class III Hitch on 2018 Toyota Highlander
  The etrailer brand Class III hitch you referenced, part # e98844 is indeed a confirmed fit for the 2018 Toyota Highlander unless the spare tire is mounted on an aluminum rim which would make the tire wide enough that it would interfere with installing the hitch. If you'll be towing with the hitch, you'll also need a trailer wiring harness like part # 118449. For a ball mount, use # AMSC2 and # 19260 for a 1-7/8 or # 63845 for a 2 inch trailer ball. I've linked to some installation videos...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?