Dimensions of the Convert-A-Ball Cushioned Weight Distribution Shank # AMAC1

Question

Question:

What is the distance in inches from the hitch pin hole to the front end of the shank front meaning opposite the ball?

asked by: Carl

0

Expert Reply:

I believe the measurement you are looking for is 7-1/4 inches. I attached a picture that shows this measurement as well as another picture that has some other measurements you may find useful.

If you need any other measurements just email me back.

expert reply by: Jameson C

0

click to enlarge

Answer 1

As long as your wheel doesn't have a specific weight rating listed you can just upgrade your valve stem to a metal one like the Americana Metal, Bolt-In Valve Stem #AM20906 and it will hold up just fine, yes. Most wheels can handle the weight…

view full answer...

Answer 2

The best option we have is the Fastway e2 Weight Distribution w/ 2-Point Sway Control - Round - 10,000 lbs GTW - Without Shank #FA94-00-1033 which measures 5" from the center of the ball hole to the center of the shank mounting holes, and then…

view full answer...

Answer 3

Based on the 30-92-XXX partial part number you provided, it sounds like you have Bargman 92 Series taillights. These taillights measure 8-9/16 inches long x 4-9/16 inches wide x 2-1/8 inch thick. I have some options for LED taillights for you,…

view full answer...

Answer 4

I went out to the warehouse and the large 3/4 inch bolts used on the Reese round bar weight distribution head #RP58112 require a 1-1/8 inch socket or wrench. For information on torque specs please refer to the instructions I have linked for you.

view full answer...

Answer 5

I ran out to the warehouse, and pulled one of the #AMAC1 shanks. I found that the distance from the end of the shank that would insert into the hitch receiver to the center of the hitch pin hole is exactly 2-11/16 inches, as you can see in the…

view full answer...

Answer 6

The lights themselves are identical. I reached out to my contact at Bargman who said that the only difference between the Bargman Tail Light Assbemly #30-92-003 and one with the part number 34-92-003 is how it is shipped to the company. One of them…

view full answer...

Answer 7

There is an issue with German vehicles (Audi, Mercedes, Porsche, BMW, Volkswagen, and so on) and trailers with LED lights. The LED trailer lights do not offer enough draw on the system for the lights to work. On a lot of these vehicles you will also…

view full answer...

Answer 8

If the trailer has LED lights then the issue isn't the adapter or the trailer. It is the vehicle. The 2012 Mercedes GL450 and other German vehicles do not work well with trailers that have LED lights. This is because LED lights do not draw enough…

view full answer...

Answer 9

We do have a few options for replacement WD shanks that have a distance shorter than 8 inches from the center of the hitch pin hole to the center of the adjustment holes. The Convert-A-Ball Cushioned Weight Distribution Shank #AMAC1 fits 2 inch hitch…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Dimensions of the Convert-A-Ball Cushioned Weight Distribution Shank # AMAC1

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching