That looks an awful lot like a Penguin or Dometic RV Air Conditioner. We offer the Replacement Cover # AT3308046006 which appears to be very similar, only white in color. The # AT3308046006 cover is 7" tall, 29" wide and 40-1/2' long. I do suggest measuring your cover to confirm fitment. The only other way to confirm fitment would be to cross reference the model number of your air conditioner. Otherwise measuring will have to do. view full answer...
I checked with my contact at Retrax and they ran your serial number. They confirmed that the F09-2027 will be the correct remote receiver kit for your cover. We have this listed under part # RTX89TR, so it looks like you were on the right track in the first place. view full answer...
According to my research we do have a few options that will work as a replacement for your E333645 LED light:
Cool White
- 180 Lumens/5,500 Kelvin # DI56VR
- 165 Lumens/5,500 Kelvin # DI86VR
Warm White
- 180 Lumens/3,500 Kelvin # DI29VR
- 165 Lumens/3,500 Kelvin # DI76VR
The Lumens rating has to do with how bright the light is while the Kelvin rating is the color of the light itself. The higher the number for each the brighter and whiter the light. view full answer...
The bushing on the Rear Hanger with Bushing # 30-20 has a 9/16" diameter and is 1-3/4" long so you'll need to use one of the bushings in the Dexter Bronze Bushings Kit # K71-291-00 as a replacement. view full answer...
That remote was unfortunately discontinued earlier this year (2023). Since it was this recent I recommend trying to locate one as opposed to finding a whole new system. You can try reaching out to Air Lift directly or look on a type of buy sell trade to see if someone is getting rid of an old controller.
If you aren't able to find a replacement remote then I recommend replacing your whole system with the Air Lift WirelessAIR Compressor System for Air Helper Springs # AL58WQ which is also... view full answer...
If you're looking for just the L-bracket for your HappiJac Electric Truck Camper Jack System # LC736514-ELKIT then you'll need part # LC182492. The flat bracket can be swapped out with part # LC182494 and the swing brackets can be replaced with part # LC182496. view full answer...
I am not 100% sure what you are asking. The newer models of the power centers/converter sections like the Progressive Dynamics 4500 Series RV Converter # PD4590K18LS8 are coming with the switch that you are referencing that allows you to switch between battery types for charging.
Older models do not have that switch and there are some converter sections that do not have the switch still. Since you have the 90 amp version of the 4500 series, we do not have a replacement converter section... view full answer...
In regards to the Thule Canyon XT Roof Cargo Basket part # TH859XT, there's a number of different parts which attach the tray to the crossbars. I have attached a photo below with a full list of these. If you can let me know exactly what you need, I'd be glad to see if we carry them but I have also attached for you below some of the parts from this list. Unfortunately, I have no way to know what you have vs. what you don't have so I'll need for you to tell me exactly what you're missing... view full answer...
I have a solution for you, but my contact over at Lippert tells me that you won't be able to replace just those casings on Solera Slide-Out Topper. The parts you need are the Replacement Idler Head and Roll Tube for Solera RV Slide-Out Awning - Black # LC87FR and the Replacement Drive Head and Roll Tube for Solera RV Slide-Out Awning - Black # LC34FR. You will want to re-use the hex rods, but you will need to replace the entire roller tube assembly to get the "arms" that are broken on your... view full answer...
I would be happy to help!
The correct replacement converter for our 6300A model 6332 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 35 Amp # PD4635V which will be a direct replacement.
This converter has a built in charger with multistage charging to extend the life your your trailer's batteries.
I included a video of the # PD4635V for you to take a look at. view full answer...
The direct replacement for your Ventline screen with model number VD0434 is # BVD0434-31 (birch white) or # BVD0434-41 (polar white). This is compatible with Ventline Ventadome roof vent models V2092, V2110, V2094 and V2119.
However, if you're referring to the plastic tabs pointed in the photo I attached, then what you need to replace is the complete frame assembly with part # BVC0573-31 for birch white, or # BVC0573-41 for polar white. This includes a new screen as well. The standard... view full answer...
For your 58 inch Lippert Edge RV awning the correct replacement idler arm is the part # LC62ED and the correct replacement drive arm (one with the motor) is the part # LC22ED. view full answer...
The correct manual override cover for your 3,500lb electric Ram jack is the Replacement Manual Override Cap for etrailer A-Frame Electric Jack # EJ-3520-BCP.
For a cover you can use the Ultra-Fab Protective Cover for Electric A-Frame Jacks # UF38-944026. This 14-1/2" x 17-1/2" weatherproof cover slips easily over your electric tongue jack and secures with a drawstring to helps to protect your jack motor from the elements. view full answer...
I spoke with my contact at Lippert regarding your older Kwikee step assembly with the 909506000 control module. He stated that in order to replace the control unit all you need is the part # LC379606. This is designed for pre-IMGL step units like yours that were manufactured between 1999 and 2005. You do not need to replace any other components. view full answer...
The correct replacement cover for your Ventline Northern Breeze VB0568 Roof Vent is the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents # BV0554-01 for white, or # BV0554-03 for smoke.
I have attached a couple of videos for you to check out as well. view full answer...
We do have replacement RV Entry Door Handles like the Global Link # 295-000019 as well as deadbolts like the Valterra # L32CS3108 with 1" throw, but these are keyed separately as we don't have an all-in-one kit with both locks keyed. Alike. You aren't the first person trying to find this solution so I'm hoping one of our manufacturers comes out with an entry door and deadbolt kit keyed alike so you won't need to use 2 separate keys to get into your RV.
Attached is a link to our selection... view full answer...
For your AL-KO T44 axles, the brake assemblies you need are the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4.4K # K23-478-479 or the manual adjust # K23-462-463-00 along with spoon adjuster # W80630.
The grease seal you want is AL-KO part 568861 which is the Grease Seal - Double Lip - ID 1.719" / OD 2.565" # RG06-050 for a set of 2 seals. view full answer...
Based on what you described wanting the best hitch solution we have for your 2019 Volkswagen Atlas is the EcoHitch part # 306-X7362 as it is the least visible option and offers best ground clearance. Instead of having the hitch tube under the rear bumper this comes out through the lower fascia section to give you much better ground clearance and also a better overall look.
The first picture I attached shows the EcoHitch and the second shows the Draw Tite # 76176. view full answer...
Since you have a Furrion Camera system with side cameras the only compatible monitors are going to be the 5" # FR97FR or 7" # FR47FR options. view full answer...
That is not normal wear for the L-Brackets on your Blue 2-Point # BLU75FR to be that worn. It looks like you have too much angle in the head, so I recommend trying to tilt the L-brackets a little to try and get the bar less on just that one edge, and verify your system is rated correctly for your trailer.
The tilting of the head is used to add tension to the spring bars so it's possible your spring bars are underrated for the tongue weight your using it for.
With all of that said for... view full answer...
Go To Results