For starters, the vast majority of cargo boxes and replacement mounting hardware for cargo boxes will not work on factory crossbars for a Nissan Xterra as they are very large in comparison to the standard crossbar sizes that these cargo boxes and replacement mounting hardware are designed for.
Unfortunately, I was not able to find any mounting hardware we offer that will work with the Xterra crossbars. I recommend taking a trip to your local hardware store as this will be your best option. view full answer...
If you can reply to this email with the pictures I can help you out. Just be sure to let me know what the product is they are installed on! view full answer...
Yes, the Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger - 12V - 45 Amps, part # PD9245C, is a suitable replacement for your Magnetek Tu-730-2 converter.
I have included a video review of the Inteli-Power RV Converter and Smart Battery Charger below. view full answer...
Tekonsha does not offer replacement circuit boards or converter boxes for their kits like the # 118547 so your best option is to go with an all new kit as it's only way to order the box. view full answer...
It sounds like you might be looking for an Access Lorado Soft, Roll-Up Tonneau Cover # 834532006380 for a 2007 Nissan Frontier with a 5 foot long bed. If you just need the replacement tarp, let me know the serial number off your rails and I can get your the correct replacement tarp to fit. view full answer...
I don't think there are any relays under the seat of a 2005 Nissan Pathfinder but there could be some behind the kick panel on the passenger's side, front. The relay that is missing or blown is likely one of the blue relays from the Curt Relay Kit # C57000. The easiest way to determine if a relay is bad is to use a known good relay in place of a potential bad one. The relays for the tow package turn signals/brake lights are under the hood. If the right turn signal one is working, try putting... view full answer...
Since you were looking at the Regal style idler head # LC672052 I'm assuming you need to replace the idler head pin on your Solera awning. You can remove the old pin and install # LC27WD for a replacement. If by key you mean a cotter pin, then yes assuming that is the style you have. Otherwise it will be a wax screw. Make sure to inspect the head for other possible damage. Lippert recommends replacing the entire idler head to ensure everything aligns correctly. view full answer...
The MaxxAir Replacement RV Air Conditioner Cover - Coleman-Mach / RVP Brand RV Air Conditioners - White # MA8335A5261 is the replacement I recommend for you and it has a simple installation. It will fit your Coleman AC unit. view full answer...
Thanks for the photos!
Your coupler has pretty generic markings, but from what I can see if looks like you need one of the following parts:
- Breakaway Cable for Model 60 Actuators # T4623800
- Breakaway Cable for Model A-75 and A-84 Actuators # DX76XR
Match this with the style you're needing to replace and you'll be good to go! I believe from your photos you need the kit for model A-75 and A-84 actuators. view full answer...
Yes, the adapter clamps that are used to secure the Extang Trifecta 2.0 Tonneau Cover # EX92985 to the Utili Track on your 2018 Nissan Frontier can be found with part # EX2244-0204. This includes all 4 clamps needed for installation.
If you can tell me what model tonneau cover you have I will be happy to verify if these will work. view full answer...
The key for selecting a replacement grease seal is the reference number, in this case # 10-9. The manufacturer code does not matter. This is a single-lip seal with an inner diameter of 1.500-inches and an outer diameter of 1.987-inches. It is compatible as a replacement for the following other manufacturers' parts:
Dexter 010-009-00
Transcom 15191VB
National 474276
NOK AR2266FO
Chicago Rawhide 14840
If you prefer a double-lip seal in this same size use # RG06-020 which is sold as a pair. view full answer...
I have a suggestion for you as the rubber style plug is obsolete when Ram switched to the new Cover # EJ-3520-BCV style which uses the Cap # EJ-3520-BCP you found. With your cover having the odd egg shape you can enlarge the hole to a round hole which you can fit with a rubber firewall plug that you can source from a local auto parts store. Do be sure to verify sizes available before cutting a hole in your current cover. view full answer...
It sounds like you're either needing to replace the axle on your trailer or you need a lift kit for them.
To replace the axle the only torsion replacement we have comes from Timbren with their Axle-Less systems. These come in a variety of options but for standard configurations we have the following:
- 5-Bolt Idler Hub # A35RS545
- 5-Bolt Brake Assembly Kit # A35RS545E
Attached is a review video of the Timbren kit as well as a link to our selection for you to filter through. If you... view full answer...
You could replace a double-eye leaf spring with a slipper spring like the # e33SR spring you'd looked at, but it's recommended that you remove the existing rear hanger (assuming it's a single axle trailer) with a rear hanger like # 115706S as your existing rear hanger isn't designed for use with slipper springs.
You'll also want to choose a spring with sufficient capacity to handle the weight of the boat and trailer. You can choose a higher rated spring than your existing one, but be aware... view full answer...
I spoke with my contact at Thule and she said that the only replacement hardware kit they can recommend with your Thule Frontier Cargo Box is the part # TH04997 that you referenced. view full answer...
The most I was able to find about the Coleman 4735CC201 leaf spring is that it's rated for 1,000 lbs which means it goes to a 2,000 lb axle. For that application we have the 4-Leaf Slipper Spring w/ Radius End # e69SR which measures 25-4/8" long from the center of the eye to the end of the spring itself. If you use a jack to raise your trailer by the frame you will be able to get under the trailer to measure the leaf spring without it being compressed and compare that to our length.
Something... view full answer...
The Replacement Wiring Harness for Tow Ready Nissan Vehicle Wiring Harness # 118267 will work for your 2012 Nissan Pathfinder as it does appear you already have the relays. However if you have a gray plug with an 8 pin that has a green wire instead of a 6 pin with orange, we don't have a fit for that 8 pin. Some Nissans have that connector instead and that causes compatibility issues. view full answer...
From your description it sounds like you are looking for the Replacement Double Ball Joint # LC388220, although this is the entire ball joint and not just the bolts. This connects the gear plate to the actuating arm on a Lippert Coach Step or Stromberg Carlson sliding step.
The only other hardware available for a Coach Step is the Replacement Joint Assembly Hardware Kit # LC216567 which is for a joint assembly and includes:
- 5/16"-18 Diameter x 1-1/4" long hex-head shoulder bolt
- 5/16"... view full answer...
Go To Results