Yes, a 24-7/8" leaf spring will work for your 2022 Dutchmen Voltage. If you took the # DX74XR and flattened it out it would measure 26-3/8" which is right in line with what you have. Assuming you have 8,000 lb axles on your toy hauler this would work well as a replacement.
I have attached a link to all of our 24-7/8" long leaf springs for your reference. view full answer...
Bummer! I can help you out. The 220 will fry the circuit breakers and the power converter. Camping trailers are made for 120V power at either 50 amps or 30 amps and have an integrated converter to 12v power for certain components like lights so that they can be utilized in a camping area where there isn't 120v power available.
If just the parallax 7355 needs replaced, then the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 55 Amp # PD4655V is a direct replacement.... view full answer...
The correct hub and drum assembly replacement for your Lippert 4,400 lb axle is the # 8-407-5UC3-EZ. This comes with bearings and a grease seal. If you need brakes as well you can use the # LC66WD, or for self-adjusting brakes # K23-478-479. view full answer...
Thanks for reaching out! What size tire (located on sidewall) is currently on your 2022 Colman Lantern 263BH and what wheel bolt pattern do you have? I tried finding those specs but they aren't readily available anywhere. If you have a specific wheel style that you're looking to match go ahead and shoot me a photo of what you have and I'll see what we have that matches!
Attached is a helpful article about wheel bolt patterns for you to check out. view full answer...
We can certainly point you in the right direction. Unfortunately, we do not have a way to cross reference a year make and model of camper to know exactly what bearing sizes you will need. If you can confirm the individual axle capacity that will help to narrow it down. The best way to know what bearing sizes you need is to pull a hub and remove the bearings. Each bearing will have a number stamped on the edge. If you are able to provide the inner and outer bearing numbers, we should be... view full answer...
To replace the Level Up controller on your 2012 Dutchmen Infinity 3750FL you need the Replacement OneControl Advantage Controller # LC88TF. I confirmed this is what you're needing with my contact at Lippert! view full answer...
Yes, the Lippert Slide-Out Switch Assembly # LC117460 would work as a replacement for your current switch, but I would definitely check out the wiring running to it to ensure there wasn't additional damage. I've attached a diagram below of each wire function based on color to help you with the installation.
To replace a slide out motor I'll just need to know the part/serial numbers on the motor. There will typically be a sticker on the motor as well as the gearbox attached to the motor.... view full answer...
Thank you for the photos, that really helps!
It looks like you're needing the 1-diode 2-1/2" round lights from Optronics; Red # MCL0040RBB and Amber # MCL0040ABB.
The lens looks to be the same design and the bases have the same mounting design as what it looks like you have as well. I've attached review videos for you to check out. view full answer...
We do have a propane gas detector you can use to replace your Atwood model 31013. The Atwood 31013 is no longer available, so it will not be a direct replacement. We have the:
-RV Propane Gas and Carbon Monoxide Detector # RS34FR for white, or the:
-RV Propane Gas and Carbon Monoxide Detector # RS54FR for black.
We also have the # RS44FR if you want it for detecting propane gas only.
All of these carbon monoxide detectors are flush mounted, measure 4-1/4" long, 2-5/8" wide, and 1/2"... view full answer...
The equalizer and shackle straps in the picture look a little worn, so replacing is a good idea on your 2011 Dutchman Denali. The Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double-Eye Springs # K71-449-00 is a great upgrade option for you that gives you the grease zerk(s) for easy maintenance. As long as you current equalizer is 7-3/4 inches on center from bolt to bolt, it is a great replacement for your application. If you have a different measurement of... view full answer...
Your 2021 Dutchmen Coleman Light 2455BH will have came with leaf springs like the Double-Eye Spring for 3,500-lb Trailer Axles # e54SR. Do remember leaf springs should be replaced in pairs. As you are wanting to move to a stronger spring I recommend the Double-Eye Spring for 4,000-lb Trailer Axles # e93SR. These will have an additional 250lb capacity per spring so you will not be installing springs which are so stiff they cause the trailer to bounce and transfer a lot of shock inside the... view full answer...
I reached out to Lippert and the correct hub and drum assembly for your Dutchman Voltage 3200 is the Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased # LC53UD. This hub has 1/2" diameter x 1-5/16" long wheel studs. It uses a # 25580 inner and # 14125A outer bearing. This hub and drum is compatible with 12" x 2" brake assemblies like the # 23-180-181. view full answer...
Since you have the Lippert Edge awning on your 2022 Coleman Lantern 17B, you'll need the following cover:
Replacement Front Cover # LC32NJ
Also just incase you find damage to the back cover, the replacement back cover is # LC43UD. view full answer...
I was able to find a picture of the part number 90110 C1 that you need and found that the exact replacement is the # BV0554-03 that you referenced. If you wanted white instead you'd want # BV0554-01. view full answer...
Based on my research your 2013 Dutchmen Voltage 3950 has a Lippert 1621 pin box from the factory. There are a couple 5th Wheel replacement pin boxes with air ride that are compatible replacements.
The Trailair Flex Air 5th Wheel Pin Box - Lippert 1621 - 21,000 lbs # LC369535 is the most popular option that uses a scissor like motion to absorb shock using the air bag and rebound shock. This pin box also has a rubber compound built into the head to absorb that initial road shock before... view full answer...
For your application you need the Pre-Greased Easy Grease Trailer Hub and Drum Assembly # AKHD-655-35-EZ-K. This matches all of the specs you mentioned and while it's only rated for 3.5K axles, it will still work for your Lippert 4.4K axle since all of the bearings and bolt pattern match up. The weight rating is more like a guide when it comes to looking at weight ratings. view full answer...
We offer a replacement metal roof vent cover that fits the standard 14 x 14-inch roof vents that are typically found on RVs. Ventline part # BV0534-00 is a plain metal finish flat lid with a continuous type hinge. This is the only metal lid we offer at this time. I linked a photo showing the hinge since this is an important aspect to its fit on the vent.
If your vent uses a different style of hinge (all types appear on the other linked photo) you can refer to the linked page for all types... view full answer...
From that number you supplied, it appears you have axles that are 5,200-lb to 6,000-lb with a 12" - 6 on 5-1/2 bolt pattern. For brake assemblies I recommend # AKEBRK-7R-SA for the right hand side and # AKEBRK-7L-SA for the left. This is a self-adjusting 12' brake assembly, mounting bolts and hardware, # BRKH12S sold separately.
If you do decide you need to replace the hub and drum assembly, I recommend, # AKHD-655-6-K. This is an etrailer replacement hub and drum assembly supplied... view full answer...
The number you provided from the lens, SAEAP2 16 DOT states that the lens is compliant with DOT regulations, but in most cases it won't help us identify the lens. However, we've gotten enough inquiries about this lens that I can identify the replacement as # A32AB which is the replacement lens for the Optronics # MC32AB lamp. You can confirm this by looking at the housing of the existing lamp which should have the part number printed on it somewhere. The lens measures 4" L x 2" W x 1/2" H. view full answer...
I have attached options for the more commonly seen vent lids used on manual opening roof vents. This is rounded dome style by VentLine in white # BV0554-01, or in smoke # BV0554-03.
If you have not previously replaced a vent cover/lid I have attached a couple of useful how-to video. In addition I suggest consider installing an enclosed trailer roof cover such as the # CAM40431. These vent covers lets you keep your RV roof vent open at all times, letting in light and air while keeping... view full answer...
Go To Results