To replace the mounting hardware for the etrailer Trailer Hitch Receiver # e22TR you need the Kit # RHK. Just input the hitch information prior to ordering and we'll send out the parts needed to get this installed on your 2015 Lexus RX 450h! view full answer...
For the old Karrite Voyager cargo box you would use replacement latch # 03347. The replacement locks and keys, # SR03807, should also be the correct fit for the box.
For the hinges, replacement parts are not available. If they are not moving freely then you may need to remove the hinges, inspect them for damage or to see if they are bent, give them a good cleaning, dry them completely, then use a house hold lubricant to assist in movement.
Cargo box lids can kind of stick a bit even when... view full answer...
Demco's warranty states "Your Demco Kar Kaddy is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year after date of purchase by the original (first) retail owner, or until it is resold or transferred by the original owner. Hubs used on the KK370SB are warranted for a period of three years after the date of purchase by the original (first) retail owner or until it’s resold or transferred by the original owner. Tires and lights... view full answer...
Yes, you can use two of the Replacement Lock Cylinder and Premium Key for Thule One-Key Systems # 1500004217, and they will both have the same N217 lock cores, so they will use the same key. You can use Replacement Key # TH1500000217 as replacement keys for the N217 lock cores. view full answer...
The Draw-Tite Class III hitch you'd looked at, part # 75676 uses 6 M12 x 1.25 x 40mm (12 mm diameter with a 1.25 thread pitch x 40 mm long) class 10.9 bolts to secure the hitch to the nuts that are welded into the frame of your Lexus RX350.
We offer a replacement hardware kit as part # RHK. On the product page, you'd input '75676' as the hitch item number and choose 'Draw-Tite' from the drop down menu. This will provide all the hardware that originally came with the hitch.
I've linked... view full answer...
For your 2006 Lexus GX470, it sounds like you are looking for the trailer wiring. You mentioned the factory tow package so it likely had a factory 7-way. If that is the case, then you will simply need the Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Flat Connectors # HM43374 which connects to the factory wiring harness already present near the driver's side frame rail in the rear. This connector has the 4-way wiring connection you will use on the... view full answer...
The TruRyde double lip grease seal set you referenced, part # RG06-050, is indeed the correct grease seal for use on a number 84 spindle with inner bearing # L68149 and outer bearing # L44649. The reference numbers you gave are the seal part numbers from other makers: number 568886 is the AL-KO part and number 09103305 is the Hayes part.
We also offer a complete bearing kit for the number 84 spindle that includes the bearings, races, seal, tang washer and cotter pin, part # BK2-100.
The... view full answer...
Actually we do list the Curt trailer wiring part # C56268 as a confirmed fit for the 2018 Lexus NX 300 now. You may have bought this before the fit was updated but currently we have this as a fit for the 2018 model. view full answer...
We do offer the hardware needed to re-install the Curt Hitch, part # 13445 you referenced.
You just need to enter the part # RHK and then enter the hitch number # 13445 in the field on the right hand side of the page. Then select Curt from the drop-down menu and enter the quantity of hardware kits you wish to order. Click Add to Cart and you should be ready to go.
If you wish to discuss shipping cost or get other information about our products you can contact our good folks in Customer... view full answer...
Those parts are only available with the Fit Kit # INTR152 for your 2022 Lexus GX 460. These will attach to your Feet # INXS350 and Crossbars # INXB138-145. view full answer...
In order to determine the correct replacement hubs for your 2004 Four Winns Trailer you will need to pull one of the assemblies. Once you have the hub removed take out the inner and outer bearings and look for a number that should be stamped right inside of each of them.
If you can't read the numbers you can also take a few measurements along the spindle with a digital caliper. I have attached an image to assist.
If you can tell me the numbers you found, or the measurements you took,... view full answer...
The Replacement Aero Bar Clip for Thule AirScreen Fairings # 8528583001 is a replacement for the TH8700, TH8701, TH8702, and the TH8703 Thule Fairings.
However since you mentioned you have the Thule Fairing for Roof Racks # TH871XT which is no longer available, this clip won't work for you, as there are no replacements available, but I do have another solution.
A new wind fairing, like the Thule Airscreen XT, will be your best bet, and will work great for you, and is compatible with the... view full answer...
Glad you're happy with the rack, and we can help you out here as we do have the correct replacement for your Inno T277 key; what you need is the following:
- Replacement Key for Inno Roof Racks, Bike Racks, and Cargo Boxes - Key T277 # IN38VR view full answer...
The bolts for the Draw-Tite Max-Frame Trailer Hitch Receiver # 75685 are M12 x 1.25 x 25 mm Grade 8. The washers are 1/2 inch. If you want the replacement hardware kit, we can send you the actual parts # RHK or you can get what you need at the local hardware store. view full answer...
To install the Draw-Tite Max-Frame Trailer Hitch Receiver # 75095 you will need one of each of the following:
M12 x 1.25 x 40mm CL10.9 Hex Bolt
1/2”-13 x 1-3/4” GR8 Carriage Bolt
M14 x 1.50 x 45mm CL10.9 Hex Bolt
The rest of the bolts are existing OEM bolts. You will also need the following hardware:
1/2”-13 Hex Nut (Qyt 1)
9/16” Hardened Flat Washer (Qty 1)
1/2” Conical Washer (Qty 2)
1/4” x 1-1/2” x 2” Block (Qty 1)
9/16” Lock Washer (Qty 1)
All of this can be found by ordering replacement... view full answer...
We do have installation hardware for the Curt # 13445. What you need is the Replacement Hardware Kit for Trailer Hitches # RHK. Make sure you enter 13445 into the "Hitch Item Number" field before you add to cart. view full answer...
Swagman offers both a non-locking and a locking anti-rattle hitch pin for their # S64400 Original bike rack.
For the non-locking pin, use part # P5901 or part # S64027 for the locking version. view full answer...
The replacement anti-sway cradle for the Thule Raceway PRO # TH9002PRO that you referenced can be found on our site listed as part # TH8523486001.
The straps that secure the bike to the cradles and anti-sway cradles are sold individually with part # 852-3006-001 or as a set of 4 straps with part # TH534. view full answer...
If there is any doubt at all, I would replace any worn parts. With a tow bar that has seen as much action as your Falcon II, # RM-520, it would be a good idea to give it some replacement parts so it will continue to serve you well.
In the realm of Falcon series tow bar replacement parts, we have the RoadMaster Autowlok Repair Kit for Falcon Tow Bars, # RM-910003-50. I have included a link to the installation details for reference. We also have the RoadMaster Replacement Button and Glue... view full answer...
Go To Results