LaSalle Bristol doesn't make it so that you can replace much on their cable actuated waste valves besides just the handle so you would be better off just replacing the entire valve and cable system with Valterra's Black # TC372 and Gray # TC172. The old valves can just be unbolted and replaced with the new Valterra valves so that you don't have to cut any pipe or glue anything in.
Valterra's cable system has a little rod at the end that clamps into an exposed port on the valve to easily... view full answer...
We do offer replacement jack options for the Kwikee Level Best 3000 Hydraulic Leveling System, part # LC359278 for 10,000 lb jacks or part # LC359275 for 17,000 lb jacks. These jacks will work on all four corners. If you don't know which weight capacity you need and it's not printed on the jack anywhere, simply provide me with the part number of the jack and I should be able to reference this for you. view full answer...
There are some replacement parts available for the Pace Edwards BedLocker tonneau cover. There is a Replacement Tailgate Top Seal for Pace Edwards Retractable Tonneau Covers # PE99CV and there is also the Manual Switch Kit for Pace Edwards BedLocker or UltraGroove Electric Tonneau Cover # 311-BL-1120. There are also some different replacement Explorer rails depending on which model you have. view full answer...
Yes, the SeeLeveL RV Holding Tank Monitor for fresh, gray, black - water pump and heater switch, # SE74VR is designed specifically to be a replacement for older tank monitoring systems. The SeeLeveL # SE74VR uses sensors that are sold separately for single-digit accuracy. The SeeLeveL sensors are mounted on the outside of the tanks, this means they are easy to install, won’t give false readings due to debris, and are easy to maintain. The SeeLeveL tank monitoring system uses technology... view full answer...
It sounds like you are going to need either the Replacement Motor for Kwikee Electric RV Steps part # LC379147 or the Replacement Gear Box and A Linkage part # LC379160. I spoke with Lippert and was able to cross reference the info provided so I can confirm these are the correct parts. In order to determine which exact component is creating the noise, I recommend isolating each (unhooking shaft from motor and applying power etc). as that would then give you your answer.
Please note, depending... view full answer...
I believe you're talking about what Reese refers to as inner brackets because they mount to the inner surface of the truck frame. They offer the inner brackets as # RP27FR, as shown in the provided photo. view full answer...
Buongiorno!
We do carry Replacement Magnet Kit for 7" Electric Trailer Brake Assemblies - 2,000 lbs
Item # AKBRKR-M7. However, it looks like the center mounting hole on yours is round, whereas ours uses a square/rectangular hole. It doesn't appear that the hole on the # AKBRKR-M7 is large enough to allow the arm (on the brake assembly) to fit through.
If you scroll to about the 5:40 min mark on the Redline Replacement Magnet Kit video Iinked below, you'll see the arm I'm referring to... view full answer...
The correct replacement brakes for brake shoes that fit your 8-283 hub and drum assembly are the # bp04-065. We also have the # K71-362-00 if you need replacement springs as well. view full answer...
The CC316-01 number you referred to is the original part number of the fan motor. Is it a replacement fan blade or motor you're needing? If that's the case, you'd use the # BVD0218-00-R replacement motor. If you were needing a replacement fan blade, one is available as part # BVD0216-00.
If you were needing the entire vent hood, I'd need the part number of the one you currently have. The hood part number would start with a PH, S0, BCL, or TCL. If you could provide that information, I'd... view full answer...
While it can be difficult to get started on these the two panels will slide into the Replacement Tail Hinge for Extang Solid Fold 2.0 Hard Tonneau Cover part # EX83475-64. Of course there is the seal to get out of the way so you can begin sliding the old hinge out. The sections have a round piece that will slide into the rounded opening of the hinge. view full answer...
The replacement step pad for your Aries Round Nerf Bars - 3" Diameter # AA203007-2 will be the # AA2090139. Though we do have them listed as fitting the oval style bars, they will also fit the round bars that you have. I included a couple pictures with measurements for you to check out as well. These will confirm the fitment for your nerf bars. view full answer...
I have exactly what you need. There is nothing special about the Marshall Model 260 Propane Regulator so you can use pretty much any dual stage regulator. I recommend either the MB Sturgis Vertical 2-Stage Propane Regulator Part # 108220 or the Camco Vertical 2-Stage Propane Regulator Part # CAM59313. They will both work as an exact replacement for you, there isn't any need to replace it with another Marshall. view full answer...
The Replacement Control Module, part # LC301702 is just what you need to replace the Frigette 202-3230 controller on your RV steps.
This unit installs under the step base and requires 4 screws for installation which are not included. view full answer...
The Lippert Ground Control 3.0 auto Leveling System does have replacement motors available. I recommend the Replacement Hall Effect Motor for Lippert Components Ground Control 3.0 Leveling System # LC343758 which is a confirmed fit for your 2014 Open Range 386FLR trailer. This motor will simply connect to your current system and will work perfectly as it measures rpms instead of amps for proper auto leveling. view full answer...
The most powerful and quietest Ac unit is the Furrion Chill Replacement RV Air Conditioner for Furrion Setup - 15,000 Btu - White # FR42PV. The unit with the box versus ducts says it has an indoor 60 db level, and a ducted unit using the same motor and compressor should be just slightly under that. view full answer...
On the underside of the cover you may find a tag or a number actually printed on the bottom of the cover. But if you know the model of the TruXedo cover then I can figure out which replacement cover you will need for your 2008 Ford F-150 with 5-1/2 foot bed.
If you have the TruXport # TX277601 the replacement is # TX2776-CVR
If you have the Edge # TX877601 I would have to have the cover added after speaking with TruXedo
If you have a different bed length let me know. view full answer...
The Reese Multi-Tow 7-Way & 4 Pole Trailer Connector # 74682 is meant to be a replacement for and existing 7-way (with factory trailer connector). If your vehicle already has a 7-way on the back, then this is the product to go with.
But if you don't have an existing 7-way, the recommended part is the Universal Installation Kit for Trailer Brake Controller 7-Way RV and 4-Way Flat # ETBC7. If your vehicle already has a 4-way flat, this kit includes everything you need to install an electric... view full answer...
What vehicle are you needing this for? It looks like you have a 2019 Ford E-Series in our fitguide but if you could let me know if it's an E-350 or E-450 and whether you have a Class A motorhome, Class C motorhome, or an Emergency Vehicle I can see what else you might need. view full answer...
I do have an option for you to replace the bottom plate of your trailer jack with a wheel assembly. The option I have is the Pro Series 6", Detachable Caster w/ Pin for 2" Diameter Jacks - 1,200 lbs # PS1400750340.
This corrosion-resistant, removable caster has fitting for 2" jack tube and is rated at 1,200 lbs. I have attached a picture that shows the dimensions of the caster. view full answer...
Go To Results