See what our Experts say about this Optronics Trailer Lights

• Correcting Hyperflashing After Installation LED Taillights on 2004 Dodge Ram 3500
  In order to stop your turn signals and brake lights from hyperflashing with your LED taillights, you will want to install LED Light Bulb Load-Resistors on the turn light and brake signal wires. Hyperflashing is a common issue when changing incandescent bulbs to LEDs. One of my fellow Experts put LEDs on his Dodge 2500 and ran into the same issue. He used the #DI34ZR Load-Resistors on his truck to solve the hyperflasing issue. I've attached an installation video of these load resistors...
  view full answer...
• Is the Optronics Trailer Tail Light # ST70RB the Correct Replacement for My 2006 Boatmate Trailer?
  Hello Jamey, Yes, the Optronics Trailer Tail Light - Stop, Turn, Tail - Submersible - Incandescent - Oval - Red Lens # ST70RB is the correct replacement for your R-SAE STIP2 A-SAE IP2P 97 DOT light on your 2006 Boatmate trailer. What is your favorite lake to go out on?
  view full answer...
• Wesbar 108121 Replacement Trailer Light
  Wesbar light 108121 is now a discontinued item but the Optronics # ST70RB is a direct replacement for it, and yes, this 6-1/2-inch oval 3-function light will work great and fit the same grommet.
  view full answer...
• Recommendation for Side Mounted Trailer Taillight
  What do you mean by side mount? Like one that mounts side of trailer frame but still points back? Do you possibly have pictures of what you are looking for?
  view full answer...
• Can Bulb be Changed in a Truck Lite 60 Series Trailer Light
  It looks like there are different versions of the 60 series tail lights from Truck Lite. If you have a sealed version meaning there is no way to open up the light then the bulb cannot be replaced. If you can access the inside of the light it looks like it takes a 2057 bulb available at an automotive supply store.
  view full answer...
• Will the ST70RB and the STL72RB Both Fit on the Same Sized Light Housing?
  To answer your question, both of the # ST70RB and the # STL72RB are 6-1/2" long x 2-1/4" wide x 2-3/8" deep lights; the main difference is that one is an LED light while the other is an incandescent. I was able to find some information on your TruckLite 60283 light and the best match to replace that light is the # ST70RB , since your trailer light system is wired for incandescent lights. If you wanted to switch both lights over to LED, you would use # STL72RB but you would likely need...
  view full answer...
  
• Replacement 6-1/2-Inch Oval Trailer Tail Lights
  Thank you for the trailer light lens coding. This is not an actual light part number; this usually appears on the light base. Just the same I think what you're looking for is a product like # STL78RB. This is a sealed 6-1/2-inch oval tail light that uses high efficiency LEDs instead of standard bulbs. You can see all oval tail lights by clicking on the linked page. Click on the filters for lens color, bulb type, etc to narrow down the range of lights shown.
  view full answer...
• Replacement Tail Light for Wesbar 108121
  The Wesbar 108121 has been discontinued but the Optronics Trailer Tail Light - Stop, Turn, Tail - Submersible - Incandescent - Oval - Red Lens # ST70RB is the ideal replacement. It works with the PVC Grommet for 6-1/2" Oval Trailer Tail Lights # A70GB. This light will use the standard 3 prong plug that if you need a replacement is # A45PB or # A47PB for the 90 degree connector.
  view full answer...
  
• Replacement Taillights for CM Trailers 2-Horse Bumper Pull Trailer
  Thank you for the DOT number from your horse trailer's brake light lens. This is not the light's actual part number; that is usually found on the light base. If you can find that reference you can search our site using that number or use the filters on the linked page to select a new light based on dimensions, shape, etc. I checked photos of CM Trailers' 2-horse bumper pull Dakota series trailers and they currently use LED type surface-mount oval lights like # STL78RB. This light's mounting...
  view full answer...
• Trailer Light Kit Recommendation for a Pace Enclosed Trailer
  For an LED trailer wiring kit that would work well on your Pace trailer I would recommend the part # TLL16RK. This part number comes with everything. The lights are rectangular though. To use the part # ST70RB you would need the grommets part # a70gb, the pigtail part # A45PB, brackets part # BK70BB, and # A35W42B.
  view full answer...
• Will Optronics Sealed Oval Trailer Stop Light Replace the Bargman Light on my 2002 Homesteader
  It will fit Bargman part # 40-06-001. Since your light is a Bargman unit, you will just need to find the part number on it somewhere. The DOT 97 number has to do with Department of Transportation regulations and you will see similar numbers stamped on most lights. If you find 40-06-001 on the light, then this Optronics light will work as a direct replacement. If you find a different part number, please write back and I will help you find exactly which light will fit.
  view full answer...
• LED Replacement for WESBAR 203561 Light
  Yes, the Optronics Trailer Light, # STL70RB, will replace the Wesbar 203561 to upgrade to LED lights. You will want to check the factory grommet when you remove the light, if the factory grommet is in good condition you can use it with the LED upgrade. If the factory grommet is worn or shows any signs of damage, now is the time to replace it. You would use the Optronics Rubber Grommet, # A70GB. Same thing on the 3-prong plug connector, check it also to make sure it is in good condition....
  view full answer...
• Availability of Replacement # STL-74RBK LED Taillights
  The Optronics # STL-74RBK is a kit that includes the # STL72RB lamp, the # A70GB grommet and the # A47PB wiring pigtail. We don't sell the kit, but we do offer the parts separately. So, if your'e needing the replacement lamp only, you'd need the # STL72RB.
  view full answer...
• Replacement Tail Light For Bargman 6-1/2 Inch Oval Light
  The Optronics light that you referenced, part # ST70RB, is an exact replacement for Bargman light # 40-06-001. If you can find that part number on your Bargman light, then we can be sure that this light is the correct replacement. Even if your Bargman light has a different part number, # ST70RB will very likely work. The dimensions of the light are 6-1/2 inches long x 2-1/4 inches wide x 2-3/8 inches deep. If your current trailer light is approximately the same size, this light will work...
  view full answer...
• Correct LED Replacement for Optronics ST70RB Trailer Tail Light
  The Optronics Fleet LED Trailer Tail Lights # TLL12RK are a slightly longer light so they aren't a replacement, but we do have the LED replacement you need for the Optronics # ST70RB. That part is the Optronics LED Trailer Tail Light # STL72RB. This light uses the same PVC Grommet # a70gb with the 3-wire Pigtail # A45PB or # A47PB (right angle pigtail) for installation. I have added a link to a video review for you to check out as well.
  view full answer...
• Trailer Replacement Light for a Model J-65 Tail Lamp
  I have a couple of options for replacement lights. The larger one is going to be an 1/8 of an inch off of your Model J-65 tail lamp. It is the Optronics Trailer Tail Light item # ST70RB you were looking at. This light is 6-1/2" x 2-1/4" and has a 3 prong plug. I have linked a diagram below that shows the dimensions of this light. We do have a slightly smaller light that is 6-1/2" wide by 2-5/16" tall it is the Miro-Flex LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 12 Diodes...
  view full answer...
  
• What is the Approximate Amperage Draw of the ST70RB Sealed Oval Trailer Light
  The Sealed Oval Trailer Stop, Turn and Tail Light, item # ST70RB, uses an 1157 automotive style bulb with two filaments. The bright filament is rated at 21 watts and the dim filament is rated at 5 to 6 watts. With the filament wattage, we can determine the amp draw of the bulb. Amperage equals watt rating divided by input voltage. Assuming a 12.8 volts input in all cases, with both filaments lit, the amperage draw would be approximately 2.1 amps. With only the dim filament lit, the amp...
  view full answer...
• Replacement Incandescent Tail Lights for Rockwood Pop-Up
  We can help you select replacement tail lights for your trailer. The linked page will show you all non-LED (incandescent) tail lights. You can use the filters on the page to sort the products by shape, size, etc. For example, # ST70RB is a popular red oval-shaped stop/turn/tail light. Since I don't know the model year and version of your truck I suggest you refer the question about changing out its lights to your local dealership. If the truck was made with incandescent lighting then it's...
  view full answer...
• Replacement Clear 6-1/2 inch Long Clear Trailer Light
  Sounds like you have something like the part # BU70CB or the # BUL22CB as they are both 6-1/2 inch long 2-1/4 inch wide clear lights that mount in a grommet and use a 3 prong style connector like part # A45CB.
  view full answer...
• Bargman 40-06-001 LED Replacement Trailer Tail Lights
  Yes we do! The LED light that is comparable to the Bargman 40-06-001 and the Optronics # ST70RB that you referenced is the part # STL002RB with the staggered 3 pin connection. We also have the kit # TLL12RK which comes with the same size lights, grommets, and pigtails. The only differences are that they have a slightly different lens design and they use 12 diodes as opposed to 1. Installation videos have been linked for you to reference as well.
  view full answer...
• Load Resistor Recommendation for Use with LED Tail Lights on a Flat Bed Truck with Hyperflash
  You will wire a load resistor into the wiring of each light socket that has an LED bulb and flashes. So basically you will need to wire a load resistor into any bulb that blinks or has a dual intensity feature that lights up when the brakes, blinkers, or emergency flashers are operated. To do this correctly, you will need to wire the load resistor on the positive wire and then either ground it to the ground wire of the bulb, or to a good frame ground. You will need to do this for all of...
  view full answer...
  
• Direct Replacement Oval Stop Turn and Tail Light for a Model J-60 Trialer Light is the # ST70RB
  Yes, the J-60 light is a 6-1/2 inch wide by 2-1/4 inch tall light that is 2-1/4 inches deep overall so the Sealed, 6-1/2 inch Oval Trailer Stop, Turn and Tail Light, 3-Function, item # ST70RB, is a direct replacement for your light. If you need a replacement grommet for the light you can use the Rubber Grommet for 6-1/2 inch Oval Trailer Tail Lights, item # A70GB, and if you need to wire the light or replace the connector you can use the right angle pigtail, item # A47PB, or the straight...
  view full answer...
• Will Optronics Trailer Light # ST70RB Fit a 1989-1990 Ranger Trailer
  The Optronics trailer light # ST70RB, is an exact replacement for the following lights: Uni Bond # SE2238R Wesbar # 203561 Truck Lite # 60202R Grote # 52182 Peterson # 421R Bargman # 40-06-001 The light manufacturer/model number information may be found on the light housing itself (not the lens). If that information is not available on the light housing then you will need to choose a replacement based on measurements (see product page) or if the trailer manufacturer has that information...
  view full answer...
• Can the Bulb in Sealed, 6-1/2 Inch Oval Trailer Stop, Turn and Tail Light, # ST70RB be Replaced
  Because Sealed, 6-1/2 Inch Oval Trailer Stop, Turn and Tail Light, # ST70RB, is a sealed tail light, the bulb cannot be replaced. You would need to replace the whole tail light if the bulb needs to be replaced.
  view full answer...

Do you have a question about this Trailer Light?