Availability of Rubber Grommet to Use with Install of Optronics Trailer Taillight # ST70RB

Question

Question:

is there a rubber boot available to go around this light and secure it in a hole in the trailer frame?

asked by: Bob

0

Expert Reply:

Hey Bob, yes we do have a rubber grommet that you can use with the Optronics trailer light part # ST70RB with the part # a70gb.

expert reply by: Jameson C

0

Jameson C.

2/17/2026

Hey Bob, did the rubber grommet end up securing your Optronics trailer light the way you wanted? Knowing how it fit could help others looking to mount the same light.

Answer 1

Tire size 4.80-12 is not found on vehicles, but is a common trailer tire size on smaller utility- and sport-type trailers. In trailer use you do want to inflate them to the maximum cold psi pressure noted on the tire sidewall. Trailer tires should…

view full answer...

Answer 2

Nick, the PVC Grommet #a70gb is 1 1/8" thick so you could use up to an 1 1/8" thick metal.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Availability of Rubber Grommet to Use with Install of Optronics Trailer Taillight # ST70RB

Products Featured in This Question

Continue Researching