See what our Experts say about this TruRyde Trailer Bearings Races Seals Caps

• Replacement Hubs for 2,700 lb Axle
  Based on your photo it looks like you have 2,700 lb axles, and we do have hubs for that size axle. However, you will need to confirm the bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them. If you are unable to find them, you need to use a digital caliper to measure your spindle to the thousandths of an inch where the bearings...
  view full answer...
  
• Recommended Replacement Grease Seals for a Boat Trailer With BT8 Spindles
  Hey Paul, it sounds like your boat trailer uses a BT8 spindle, so you can use the Double Lip Grease Seal # 34823. This seal has an inner diameter of 1.25" , an outer diameter of 1.98", and will work with BT8 spindles.
  view full answer...
• Replacement For 125255UC Grease Seal
  Hey there Brad, We do have a replacement for the 125255UC grease seal; the correct seal is the following: - Double Lip Grease Seal # 34823
  view full answer...
• Why Would Seals Leak after Installation of Kodiak XL ProLube Kit
  I spoke to my contact at Kodiak and he informed me that he sees this problem a few times a week and it's always because the trailer is an EZ loader or a Tinker trailer that actually has 1.683 spindles instead of 1.72 and that is why the seals leak. The only real solution I can provide for you would be to go back to your previous setup or look into replacing your spindles or axles.
  view full answer...
• Replacing A 125255UC Double Lip Grease Seal
  The 125255UC seal has a 1.249" ID and a 1.983" OD and for that our part # 34823 will be the correct replacement.
  view full answer...
• Replacement Trailer Hub Seal for TCM 12194TC
  I did some research and found that the 12194TC seal you said you have measures 1.250 inside diameter, and 1.979 outside diameter. The seal I recommend is part # 34823. The dimensions listed for this seal are 1.249 inside diameter and 1.983 outside diameter.
  view full answer...
• What is Difference Between Grease Seals RG06-010 and 34823
  Hey Marc, the difference between the two grease seals is that the part # 34823 is sold individually and the part # RG06-010 is sold in pairs. Aside from that they are the exact same seal. How many seals are you in need of?
  view full answer...
• Replacement for Trailer Hub Marked 17002
  Hi Blake; 17002 isn't a part number for a hub I have any information on. You will need to either identify it with the axle tag or pull the hub and identify the bearings and bolt pattern to find a replacement. The bearing numbers may be stamped on the side so start by checking there. If they're worn or missing, you will need to measure the inner diameter using a digital caliper # PTW80157. Once you have this information, add it to the comments below and I'll help you find the right part....
  view full answer...
• Looking For Double Lip Grease Seal For Knott Trailer Hub
  Hello Duane, thanks for reaching out. Looking thru all our seals, I am not seeing we have an exact match for that, but we do have something similar. The closest thing we have would be the Double Lip Grease Seal # 34823 which is 1.983" OD and 1.249" ID. So very close - within a few hundredths of the specs you listed. Some of the Knott hubs use older seal sizes that are now obsolete, so it might be tough to find an exact match. Our seal is similar enough and inexpensive enough that I feel...
  view full answer...
• Replacement Hub Components For Trailer With 1 Inch Solid Axle
  With the numbers of the seal and bearings you provided, I was unable to find components that would match those you said you have. You said you have bearings that are part # L44643 and your seal is PT 203025. The only race we have that is designed to work with the # L44643 bearing is part # L44610. This race has an outer diameter of 1.980 inches. I recommend using a digital caliper like part # PTW80157 and measure your spindle in the area noted for the race in the attached drawing to make...
  view full answer...
  
• Correct Bearing Buddy for the Trailer Idler Hub Assembly Part # AKIHUB-440-2-2K
  Yes, the correct Bearing Buddy Bearing Protectors for the Trailer Idler Hub Assembly part # AKIHUB-440-2-2K is part # BB1980A-SS for stainless steel or part # BB1980A for chrome plated.
  view full answer...
• Replacement 8-259 Hub With 2,000 lb Capacity and 5 on 4-1/2 Bolt Pattern
  In order to find the correct hub for your trailer you will need to take the current hub off, take it apart and find the bearing numbers, which will be stamped on the bearings themselves. If you get back to me with that information I may be able to help you find the right hub.
  view full answer...
  
• Replacement for Bearing LM48548 and Grease Seal 10-4
  Grease Seal # RG06-050 has an inner diameter of 1.719" and outer diameter of 2.565", you mentioned you have grease seal 10-4 and it has a width of .5" but from my research it looks like a 10-4 seal has an inner diameter of 1.249" and outer diameter of 1.983". I strongly recommend using a digital caliper such as # PTW80157 to measure the seal, as well as your spindle where the seal rides in order to get the correct replacement. If it does have an inner diameter of 1.249" and outer diameter...
  view full answer...
• Recommended Seal For Bearing Buddy Protectors
  The Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair) # BB1980A-SS are designed for that blue seal to expand and eventually have visible grease around that edge. I've attached a video that shows this installation and grease application for you. The grease needing to be applied almost every trip is not normal, so I recommend the Spindle Grease Seal Set # BB60002 to contain your grease with a tight seal intended for this application.
  view full answer...
• Bearing Kit Recommendation Using L44649 Inner And Outer Bearings
  We do offer bearing kits that have part # L44649 for the inner and outer bearings, but the seal included in the kit does not match the 12194TC seal you said you have. We do have replacement seals that may work just fine for you. I did some research and found that the 12194TC seal you said you have measures 1.250 inside diameter, and 1.979 outside diameter. The seal I recommend is part # 34823. The dimensions listed for this seal are 1.249 inside diameter and 1.983 outside diameter. The...
  view full answer...
• If Bearing Buddy Overfills Trailer Hub and Blows Out Seal Is it Okay to Still Use
  If you blow out a grease seal on a trailer hub by overfilling it with grease using a Bearing Buddy the seal would not still be okay as it would need to be replaced but the Bearing Buddy like the # BB1980A-SS would still be fine. It's very easy to overfill trailer hubs with Bearing Buddies as many have found. If you are in need of a replacement seal let me know the number that's on it or the inner and outer diameter and I can get you set up with a replacement. I also attached a link to...
  view full answer...
• Spare Parts for Harbor Freight HaulMaster Utility Trailer 90154
  We often hear of weak customer support and limited spare parts availability with "bargain" trailer manufacturers. I found an online copy of the owner's manual for the Harbor Freight Haulmaster utility trailer model 90154 but it includes no information at all about the bearing or seal part numbers it uses. Often these foreign-made trailers use odd bearings that are not commonly available. If you can, pull a hub and find the part numbers on your bearings and seal. Please refer to the linked...
  view full answer...
  
• What is Replacement Grease Seal for Dexter Axle with 2,096 lb Weight Capacity
  Hey Amie, for a Dexter axle with the weight rating you listed the correct grease seal would be the part # 34823.
  view full answer...
• Safe Grease Gun Pressure for Filling Hubs with Grease on EZ Lube Spindles
  Care should be taken when loading grease into a hub that is installed on an EZ-Lube spindle. It is very easy to over-fill the hub and apply too much pressure and blow out the grease seals. Even the double-lip seals like # 34823 used with EZ-Lube hubs can be blown out from excess grease pressure. The standard grease guns we offer top out at a maximum pressure of 7000-psi, but many are rated for lower pressure, such as # ALL940798 (4500-psi) and # L30100 (3000-psi) and it's cartridges...
  view full answer...
• Replacement Grease Seal for a CE Smith Multi Sport Plus Boat and Kayak Trailer
  Hey Todd! The CE Smith Multi Sport Plus Boat and Kayak Trailer item # CE48870 uses item # CE13311 hubs. The correct replacement grease seal is item # 34823, which has a inner diameter of 1.249" and an outer diameter of 1.983". Let me know in the comments below if you need any additional help.
  view full answer...
• Replacement Grease Seal for Rockwell American 2K Spindle
  For a 2,000 lb axle, the Double Lip Grease Seal - ID 1.249" / OD 1.983" - Qty 1 # 34823 is the most standard size grease seal. You may want to use a digital caliper like # PTW80157 to confirm these dimensions match your hub and spindle. I've attached a video to assist.
  view full answer...
• Looking For ID 1.250" / OD 1.979" Double Lip Grease Seals For Jet Ski Trailer
  Hey Kevin! Yes, we do have a double-lip grease seal in the size you need. Here is what I recommend: - Double Lip Grease Seal - ID 1.249" / OD 1.983" - Qty 1 # 34823
  view full answer...
• Looking for Replacement Grease Seal for Trailer Hub Marked PT411250
  Hey Carl, so I was able to find some cross reference info on the hub part number you mentioned and based on that the correct replacement seal would be the part # 34823 which has an inner diameter of 1.249 inch and an outer diameter of 1.983 inch.
  view full answer...
• Replacement Trailer Grease Seal for part Number CR12124
  Hey Rick, based on previous customers we have found that the grease seal # 34823 is the correct replacement seal for the CR12124 that you have now.
  view full answer...

Do you have a question about this Trailer Bearings Races Seals Cap?