What is Replacement Grease Seal for Dexter Axle with 2,096 lb Weight Capacity

Question

Question:

Hello. What grease seals do I need for a Dexter axle with a s/n of 133218387017, 2,096lb capacity and HF of 70”

asked by: Amie T

0

Expert Reply:

Hey Amie, for a Dexter axle with the weight rating you listed the correct grease seal would be the part # 34823.

expert reply by: Jameson C

0

Jameson C.

9/8/2025

Hey Amie, did the grease seal I recommended work out for your Dexter axle? I'm asking because your experience could help others with similar axle setups.

Answer 1

It is a very good idea to keep spare bearings and seals (and wheel bearing grease too) on hand for the unexpected roadside stop. We have individual bearing and seal parts like #L68149, #L44649 and #58846 as well as kits like #BK2-100 that combine…

view full answer...

Answer 2

For the Lippert 4,000 lb axle trailer hubs the bearings are #25580 for the inner bearing and #LM67048 for the outer. So for a kit that has both you'd want the #BK3-310. Then for self adjusting brake assemblies you could use the part…

view full answer...

Answer 3

Hey Roger, for the Lippert 4,000 lb trailer axle we have found that the bearings used are the same as the 3,500 lb axles so you would just need the part #BK2-100 for a kit that includes the bearings and the seal.

view full answer...

Answer 4

Hey Kyler, thanks for reaching out! **UPDATE IN COMMENT SECTION - JUMPER LOCATION IS DETERMINING FACTOR** The Progressive Dynamics Replacement Section #PD4655V is compatible with lithium batteries. There is a button on the board (see photo) that…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hey Scott! The correct bearing kit for your Dexter 6k axle is the Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal #BK3-100. If you want the Dexter version it is the #DX26ER. What kind of trailer do you have?

view full answer...

What is Replacement Grease Seal for Dexter Axle with 2,096 lb Weight Capacity

Product Page this Question was Asked From

Continue Researching