Arrives before Christmas 
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Magnet kit with green wire allows you to replace the worn out magnet on 10" trailer brakes, rather than having to replace the entire assembly. The oval design increases the efficiency while also extending the life of the magnet.
Features:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're gonna take a look at the replacement trailer brake magnet kit for Dexter and Hayes Alcove 10 inch trailer brakes. This magnet kit will allow you to replace the worn out magnet on your 10 inch trailer brakes, helps you save money and time, because it's better than having to replace the whole brake assembly. This part is designed to work with the following 3500 pound axle brake assemblies. It fits the Dexter 10 inch by 2 1/2 inch brake assemblies, part number 23-26 and 23-27. It fits the Dexter 10 inch by 2 1/4 inch never adjust brake assemblies, part number 23-468 and 23-469, and the Hayes Alcove 10 inch by 2 1/2 inch brake assembly, part number 60202803 and 60202703. As you can see here, it has a nice oval magnet design it.
This increases the efficiency of your brakes and will help extend the life. The sleeve, right here, you'll notice, this will protect the wires from any abrasion. That's the part that goes through the backing plates so if there's any movement you don't want those wires to be cut into. Now, it does the two wires connected so they do need to be connected when you install this. One goes to your brake feed, one goes to a ground, and they're both green wires, so either wire can be used for either function. This part includes everything shown here on the table, the magnet itself, the two springs, and the hold down clip.
A few dimensions on the magnet, just to give you the length of it, from one end to the other is right at 3 5/8 inches long. It's going to be 2 1/8 inches wide, and the overall height of it is right at about 7/8 inches tall. That should do it for the review on the placement trailer brake magnet kit for Dexter and Hayes Alcove 10 inch trailer brakes.
thse magnets work great
Worked great easy install
Works great as described. Installation vidio was very helpful! Thanks
Fit right in, work great, good price, what more can I say?
Recieved the brake magnets, one day ahead of schedule, put them on, they work perfectly.
Came right on time to install prior to our trip tomorrow. Price was great 1/3 of what our local RV dealer wanted.
Perfect replacement for the original magnets that had gone bad.
The product was exactly what I ordered. I Received it on time and at a reasonable price.
Easy install, works great. Shipping was timely. Would use etrailer again.
Great service and saved over half from my local trailer repair shop Thanks
Worked as it should. Attached easily, wires are long and that is helpful with tucking connections away. Wear indicators are helpful with monitoring magnets.
Perfect fit as a replacement for my Quality Axle (used on PJ trailer) 3.5k axle.
not exactly what i needed but i managed to make it work.
the way the magnet mounted to the brake arm was slightly different from i had orignally
Snapped in place fit perfect on a 1998 Holiday Rambler with 3500# axles. Connected wiring and tested back in business brakes now work.
I am well pleased with your product and the fact that I can get parts from you, that I am unable to get here, there is no trailer parts to be had anywhere close to where I live. Your service is very good, quick delivery, it makes it easy for me to order and know I will get what I ordered in record time.
thanks
Bennie
All 3 items I ordered have worked as expected. It is great you had everything in stock. This makes choosing ETrailer my first choice.
Great quality and what I had needed to do the job. Delivered on time..
i ordered an electric brake controller, and it worked perfectly. It came in the time frame as ordered, and was exactly what I had ordered. I took it to a repair shop and the mechanics installed it and, voila, I had brakes!
Had some difficulty installing until I figured out that removing the entire brake assembly including the backing plate allows bench top installation vs trying to install on the trailer. The magnet works as expected and I now have four wheel brakes instead of three!
My AL-KO axle has the text "AL KO 08 05" stamped into the brake shoes in the hub with 10x2.25 brakes and 4.5 inch bolt circle.
Its not exactly the same as the original AL-KO magnet on my trailer - but from all I could tell a perfect fit. The lead wires are plenty long to reach outside the hub before splicing.
This magnet is just what I needed to replace the magnet who's wires wire sheared off at the backing plate when a tire failed. The reasonable price was nice too!
Still working. It is almost never the magnet that wears, but the wires inside the drum that always seem to wear thru and short on some moving part. Trailer brakes what can I say, the design is an after thought. Like when the cable guy runs the wire in your house...
The wires on the old magnet broke off right at the magnet so it wasn't repairable.
This was exactly what we needed, shipping was well priced and quick.
Lindsey G.
5/14/2019
Wow a year later? Weather has been so poor that we dont even have the camper yet. Magnet worked great, Ive bought a couple from etrailer now and will continue to use etrailer for smaller maintenance items.
Service was great and part was as described. After replacing these it did not solve my brake problem. It was a short in the wire going through the axel. Check that first if your brakes are not working. I replaced the wire an all was good.
Bought a new second had trailer.
Wasn't sure of the axle make and model.
Stripped out the bearings and found the grease seals rubber lip very hard.
Called E Trailer and Phyllis was excellent in working with me to identify the correct seals but with a double lip.
Ordered and received very smoothly-- as promised.
I am going top fit them tomorrow but have already offered up the OD to the hub and the ID to the spindle and I know that I have the correct seals.
Seals look to be good quality and I expect them to be fine.
At a sale price cheaper than a no name locally sourced magnet, the savings was a no brainer. The shipping was fast and communication from etrailer is top notch. The product itself is good quality, pig tail plenty long to splice wherever is convenient, the spring is actually larger in diameter and stiffer than OEM which I count as a plus. It pays to do business with etrailer, you WILL be satisfied with your experience.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Dalton B.
11/16/2020
Im not sure. I traded that trailer in on a new bigger one, so I cant comment for sure, but it was working perfectly when I traded it in.