Size of Gauge and Length of Lead Wires on Dexter Trailer Brake Magnet for 10" Hubs

Question

Question:

What is the gauge and length of leads on the BP 01-110 brake magnets? Thanks,

asked by: Dan V

0

Expert Reply:

I went out to the warehouse and pulled a Trailer Brake Magnet for 10" Hubs # BP01-110 and took some measurements for you. The brake magnet lead wires are 16 gauge wires and they measure 18 1/2 inches long.

expert reply by: Chris O

0

Answer 1

There is no difference between buying the brake assemblies individually or as a kit with the Dexter Nev-R-Adjust Electric Trailer Brake Kit - Left and Right Hand Assemblies #K23-478-479. Prices have to do with things like demand, and some people only…

view full answer...

Answer 2

The Dexter Nev-R-Adjust Electric Trailer Brake Assembly equivalent to your current assemblies is part #K23-478-00 for the left and part #K23-479-00 for the right side. Please check the mounting pattern of your current assemblies to the #K23-478-00…

view full answer...

Answer 3

Yes, the hub and drum kits for a 3,500 lb axle will work just fine with your 4,400 lb axle. The Dexter Nev-R-Adjust Electric Trailer Brake Assembly #K23-478-00 you referenced has a 10" diameter which matches with the 3,500 lb assemblies as well.…

view full answer...

Answer 4

By the time you add up the cost to replace the magnets and shoes on your trailer you are at the cost (or more) for all new assemblies plus you end up saving yourself the trouble of messing with trying to install all the components. For an exact…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Size of Gauge and Length of Lead Wires on Dexter Trailer Brake Magnet for 10" Hubs

Product Page this Question was Asked From

Continue Researching