Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide

See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Trailer Hitch and Wiring Needed for a 2022 Ford E-350 Van
  Thank you for reaching out! It looks like the 2022 Ford E-350 doesn't have an exact fit trailer hitch so you'll need to install a universal hitch like the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR and then universal wiring like the 4-Way # 119178KIT or 7-Way # 22551. This isn't really ideal but it's the only way to get a hitch on your vans. Unfortunately the hitches designed for an F-350 frame won't work with an E-350 van frame so this is all going to be custom work that...
  view full answer...
• Will The Draw-Tite Trailer Frame Hitch Receiver Fit A 1974 Chevy K5 Blazer With A Gas Tank Shield
  The Draw-Tite Max-Frame Trailer Hitch Receiver 75129 should fit with any OEM parts but just to be used I went out to the warehouse and measured the hitch. From the back of the crossmember tube to the center of the first bolt hole is 1". The distance between the inside of both mounting ears is 30-1/4". This hitch should sit directly under your frame rails so you can use that 1" measurement to see if the tube will run into interference with your gas tank shield. If this doesn't work then...
  view full answer...
  
• Trailer Hitch For RV on CHevy Express Chassis
  For the hitch, you'll need to go with a universal weld-on option, and since the frame is 42 inches apart, and you need a drop of at least 4 inches, the best option is the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. The # C47CR will give you a drop of about 9 inches from the frame (which is the closest available to needing at least 4 inches), and is for frame widths up to 44 inches wide. You mentioned Class 4 but I assume you're good with a Class 5 for that added bit of strength. Then...
  view full answer...
• Recommended Hitch for a 2011 Itasca Suncruiser 35P Motorhome
  Yes, there is and you are in luck because there is a custom fit option. The Curt Trailer Hitch item # C14082 will bolt directly to the frame of your 2011 Itasca Suncruiser 35P. This is a class IV hitch with a 2" receiver. It has a 10,000 lbs towing capacity and a 1,000 lbs maximum tongue weight. The Curt Trailer Hitch item # C14082 fits frames that are 34" wide. It also does require drilling as there are no predrilled holes for a hitch. If your frame is wider than 34" you will need to...
  view full answer...
• Trailer Hitch Option For 2017 Ram Promaster 3500 Cab & Chassis
  For your 2017 Ram Promaster 3500 cab and chassis service body, you'll need a weld-on hitch. There are three options from Curt that will work with frames that measure up to 44 inches (from outside to outside), with the only difference being the drop they provide (the distance from the bottom of the frame to the top of the receiver - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt Class 5 Universal Weld-on Hitch...
  view full answer...
• Front Mount Hitch Receiver Recommendation for a 2023 Ram ProMaster 1500
  For a front mount receiver I recommend checking out the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. This will give your 2022 Ram ProMaster 1500 a 2" front receiver and the brackets can be adjusted along the trimmable crosstube to fit a variety of applications. Since this is a universal-type installation you (or whoever is doing the installation) will be responsible for making sure it's installed correctly. I'm attaching a review video and the installation instructions for...
  view full answer...
• Solution for Trailer Hitch Receiver on 1997 Toyota Hilux Surf SSR-X
  I do have a solution, but there are no custom fit hitches with a bolt-on installation for your 1997 Toyota Hilux Surf SSR-X. The only option is to use a universal hitch like the Curt Class 5 # C47CR. This weld-on hitch fits vehicle frames up to 44". We recommend taking it to a certified welder for installation.
  view full answer...
• Trailer Hitch Receiver for 2019 Freightliner Sprinter 1500
  I do have a solution, but there are no custom fit hitches for the 2019 Freightliner Sprinter 1500. I recommend the Curt Class 5 Universal Hitch # C47CR. This fits frames from 18-44" and has a 2" receiver. It is a weld-on hitch so you will need to take it to a certified welder for installation.
  view full answer...
• Hitch For 1993 Ford E-350 RV With 42 Inch Frame
  Thanks for the frame dimensions, and while there are hitch options for your 1993 Ford E-350 RV, I checked with the hitch manufacturers and there are no custom fit options. So what that means is in order to add a hitch to your RV, you would need a universal weld-on hitch. There are three different options, with each of them being Class V hitches with a 2 inch receiver, and fit frames that are between 18 inches and 44 inches wide, so they will fit your '93 E-350's 42 inch frame. The difference...
  view full answer...
• Heavy Duty Hitch For 2013 Coachmen Leprechaun Class C
  I have a solution for you. I see a couple of options, you can go with the Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop # 15901. It is a weld-on hitch with a Gross Trailer Weight (GTW) of 15,000 pounds and a Tongue Weight (TW) of 1,500 pounds Or we have the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. This is a weld-on hitch with a GTW of 16,000 pounds and TW of 1,600 pounds. You will also need the brackets with this one. We have the 7" Weld-On Bracket...
  view full answer...
• Options for Front Mount Hitch 1987 E-350
  etrailer does not have a confirmed custom fit front mount hitch for a 1987 E-350 listed; I checked with our suppliers, they do not manufacture a front mount for this specific vehicle. I suggest consideration of one of the universal mount hitches such as Curt Adjustable Trailer Hitch Receiver - 18"-51" Wide - 2" Drop - Class III - 2", # C13701. Or the Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide, # C47CR. Either of these options may require additional fabrication...
  view full answer...
• Solution for Spare Tire Carrier on 1977 GMC Motorhome
  The # TR-2 fits 4" square and 4-1/4" square bumpers. This and other carriers like it will not fit your 1977 GMC Motorhome, but I do have some other options. The first is to mount the Buyers Products Truck Spare Tire Carrier for 19-1/2" Rims or Smaller # 3375201010 on the back. This can either be bolted on (drilling will be required) or welded on. The other option is to use a hitch mounted spare tire carrier like the # e98ZR. Of course this will require you to have a trailer hitch receiver...
  view full answer...
• Recommended Trailer Hitch for a Thomas Saf-T-Liner School Bus
  The best option to add a hitch to your 2006 Thomas Saf-T-Liner School Bus is going to be the Curt Class 5 Universal Weld-on Hitch w/ Brackets item # C97CR. This is a universal hitch that fits frames from 18" to 62" wide. This is our highest rated universal hitch and it has a 20,000 lbs towing capacity. The included brackets will drop of 9" from your bus's frame. There are no custom fit hitches for your Thomas Sf-T-Liner and this is going to need to be welded to your frame for the capacity...
  view full answer...
• Is There a Aftermarket Trailer Hitch Receiver For a 2006 Toyota Tundra With Factory Tow Package?
  That is correct. I do not currently see any aftermarket receiver which will replace your factory receiver on your 2006 Toyota Tundra. To use an aftermarket custom fit receiver you would have to source a rear bumper and support which fits a Tundra without a factory receiver. You could also use a Weld-On Receiver # C47CR and have it custom mounted to your frame. To do this you will want to visit a fabrication shop first to determine they will be able to complete the installation.
  view full answer...
• Hitch Options For Older Ambulance
  There may be an option for a hitch for your older ambulance, and you are correct you will need a universal hitch that is welded on. There are three options from Curt that will work with frames that measure up to 44 inches wide (from outside to outside), with the only difference being the amount of drop they give you from the bottom of your frame: - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt Class 5 Universal...
  view full answer...
• Hitch Option For 2011 Chevy Express Cutaway Van
  There are no custom fits for a trailer hitch on your 2011 Chevrolet Express cutaway van, but you may be able to use a universal weld-on hitch. So long as your frame measures no more than 44 inches wide from outside to outside you can use the Curt Class 5 Universal Weld-on Hitch # C47CR.
  view full answer...
• Option For Trailer Hitch For Holiday Rambler Motorhome
  There is possibly an option for a trailer hitch that fits your 2004 Holiday Rambler, and I say possibly because while a custom fit hitch is not available, there are universal weld-on hitches. This depends on the width of your frame from outside to outside, so if your frame measures up to 44 inches (from outside to outside), you can use any of the following. - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt...
  view full answer...
• Solution for Front Mount Hitch on 2007 Dodge Sprinter 2500
  I do have a solution, but there are no custom fit options available for your 2007 Dodge Sprinter 2500. What you can use is a universal hitch like the Curt # C47CR. This is a Class V weld-on hitch so we recommend taking it to a certified welder for installation. The hitch has a 2" receiver, a 9" drop, and fits vehicle frames 18-44" wide. If you need taller brackets the # C99CR is also available with an 18" drop.
  view full answer...
• Solution for Class V Hitch on 2011 Fleetwood Expedition Motorhome
  For hitch fabrication we only offer the receiver tube like the # E-11 or # C49511. You would need to take this to a local fabricator and they would be able to fashion a hitch and brackets that will fit your 2011 Fleetwood Expedition Motorhome. The other option would be to use one of the universal Class V hitches we have listed for your motorhome. We have the Curt # C47CR with a 9" drop and the Curt # C99CR with an 18" drop. Both options have a 2" receiver. The # C37CR and # C87CR are...
  view full answer...
• Removable Winch For 2007 Chevrolet Suburban Overlander
  The only option you have for the front of your 2007 Suburban is like this Curt front hitch # C31012. Since you have a custom built front bumper, you may want to get something like this universal weld on hitch # C47CR. This will have 16,000 GTW so it should be plenty strong. If you can make that work, you will be able to get the set up you're wanting. You could then get this Bulldog Winch Receiver Mount Kit # BDW20155 with this 12K Winch # BDW10043. We have a bunch of weld on hitches,...
  view full answer...
• Front Mounted Trailer Hitch Options For A 2024 Jeep Wagoneer
  Hi Stephen, There isn't a custom-fit front hitch available but we do offer adjustable-fit weld-on trailer hitches that you can cut to fit your frame and weld in place. We offer a variety of drops so you'll want to do a bit of measuring on your Wagoneer to figure out the best drop to fit the receiver tube either through fascia or beneath it. Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...
• Front Mounted Trailer Hitch Receiver Options For A 2003 Nissan Frontier
  Hi Hank, It unfortunately looks like there aren't any custom-fit front mounted trailer hitch receivers for your 2003 Nissan Frontier so the next option would be an adjustable-fit weld on hitch. We offer a few different drops to help get the receiver tube under the fascia so you'll need to do some measuring from the frame to determine the drop needed. Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop...
  view full answer...
• Front-Mounted Hitch Options For A 2021 Chevy Silverado 1500 3.0L Duramax
  Hi Kelly, There unfortunately are no custom-fit front mounted trailer hitches available for Diesel models of the 2021 Chevy Silverado 1500 so you would have to go with an adjustable-fit weld-on hitch and measure for the correct drop needed/check for any obstructions that could prevent fitment with the mounting brackets to the frame. We offer the following options: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop...
  view full answer...
• Replacement Trailer Hitch Options for a 2008 Coachmen Cross Country 38' Motorhome
  The mounting brackets on the Curt Class 5 Universal Weld-on Hitch # C47CR do need to be in that upright position so while this hitch can technically fit with your motorhome chassis, you'll need to get creative on how to properly weld the brackets to the frame. For an alternative option with the brackets that are in the same orientation as your frame brackets I recommend the Multi-Fit Motorhome Trailer Hitch # 5350 which fits 24" - 46" wide frames and is rated for 5,000 lbs towing. If...
  view full answer...
  

Do you have a question about this Heavy Duty Receiver Hitch?