Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop

See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Can A Hitch Extender Be Used With A Front Mount Trailer Hitch To Park A Travel Trailer
  Hi Don, Hitch extenders place a lot of stress on the hitch because you're leveraging the weight further out so using one typically drops the capacity by 50% when towing. You'd be doing it in a parking lot situation where you wouldn't really be traveling much just more so maneuvering around so realistically that shouldn't affect you but depending on how much weight you're leveraging there could be a breaking point, we just wouldn't be able to know exactly what that point is. The Curt...
  view full answer...
• Motorhome Hitch Upgrade to Use with 472-Pound Motorcycle on the Ultra-Fab # UF48-979033
  As far as mounting your 472-pound motorcycle along with the 52-pound Ultra-Fab Dirt Bike Carrier # UF48-979033 on your hitch rated for 500-pound hitch, you should definitely upgrade the hitch. This is because it is extremely dangerous to exceed the rated weight capacity of your hitch. While we do have a great option for you, the only Class IV universal hitch we carry is specifically constructed to be used with service vehicles. That is the Buyers Products # 3371801053. For an option that...
  view full answer...
• Trailer Hitch Option For 2017 Ram Promaster 3500 Cab & Chassis
  For your 2017 Ram Promaster 3500 cab and chassis service body, you'll need a weld-on hitch. There are three options from Curt that will work with frames that measure up to 44 inches (from outside to outside), with the only difference being the drop they provide (the distance from the bottom of the frame to the top of the receiver - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt Class 5 Universal Weld-on Hitch...
  view full answer...
• Will The Draw-Tite Trailer Frame Hitch Receiver Fit A 1974 Chevy K5 Blazer With A Gas Tank Shield
  The Draw-Tite Max-Frame Trailer Hitch Receiver 75129 should fit with any OEM parts but just to be used I went out to the warehouse and measured the hitch. From the back of the crossmember tube to the center of the first bolt hole is 1". The distance between the inside of both mounting ears is 30-1/4". This hitch should sit directly under your frame rails so you can use that 1" measurement to see if the tube will run into interference with your gas tank shield. If this doesn't work then...
  view full answer...
  
• Class V Trailer Hitch Receiver Option For 2023 Thor Challenger Motorhome on Ford F-53 Chassis
  We have a couple options for a heavy-duty Class V hitch, and while there is not a custom-fit option for your Thor Challenger motorhome on a Ford F-53 chassis, you can still add a weld-on hitch. From my research, the rear frame on the F-53 chassis is 34 inches from outside to outside, but you'll need to measure the distance you need from the bottom of the frame to the top of the receiver. Once you know that, you can choose from any of the following Class V hitches: - 3" Drop From Frame:...
  view full answer...
• Class V Hitch With Drop For 34 Inch Frame Rails on Custom Truck
  We definitely have some options that will work for you, though in regards to the specific hitches you asked about, the Curt Trailer Hitch Receiver # C15300 is 36 inches between the bolt holes, while the Curt Trailer Hitch Receiver # C15410 measures 34 inches between the bolt holes. So neither is going to fit 34 inch wide outside-to-outside frame rails, which makes sense as these are custom-fit hitches. What you can use instead is a universal weld-on hitch that doesn't require that specific...
  view full answer...
• Option For Heavy-Duty Hitch on Motorhome
  Since there isn't a custom-fit option for your motorhome, the only possible option for a heavy-duty hitch would be a universal, weld-on type. There are three options from Curt for frames that measure up to 44 inches (from outside to outside), with the only difference being the drop they provide (the distance from the bottom of the frame to the top of the receiver - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop:...
  view full answer...
• Hitch for 2005 GMC C5500 Topkick with Tommy Lift
  The # TLF1003-30 hitch you're asking about is designed for a 1999-2016 Ford F350, F450 or F550 chassis/cab and wouldn't fit your Topkick. For your truck, you'd need a multi fit hitch for heavy duty trucks as none of our vendors offer a custom made fit. In order to choose the correct one, you'll need to know the needed drop, height difference between the rear bumper and the underside of the Tommy Lift. If these heights are even, use the # 3371801050 from Buyer's Products. For a 3 inch...
  view full answer...
• Class V Weld-On Trailer Hitch for a 2001 Fourwinns RV on Ford E-450 Van Chassis
  If Curt trailer hitch # 15901 was welded so that the top of the cross tube was flush against the bottoms of the frame rails the drop would only be about an inch or so. The other weld-on options would have even more drop so the Curt hitch is your best option.
  view full answer...
• Is There a Class V Trailer Hitch Receiver Available For a 2002 GMC Yukon XL 2500? ?
  Looking online it appears the frame used on your 2002 GMC Yukon XL 2500 was also used on the Suburban 2500 and Avalanche 2500 for the model year. I do see a Curt Trailer Hitch Receiver available in a Class IV # 14080 rating but there is not a class V custom fit receiver for any of these models. Do note since we have not confirmed the fit of this receiver on Yukon XL 2500 you may be best going with a Universal Class V Receiver # 15901. While this will require welding onto your frame you...
  view full answer...
• Class 5 Trailer Hitch Receiver for Frame Measurement of 33-1/2 Inches
  There are a number of options for Class V trailer hitch receivers that are weld-on options and fit a frame width of 33-1/2 inches, it just depends on what is best for your application in terms of drop (there isn't anything custom fit for your Isuzu, hence a weld-on hitch being the only option). - Curt Class 5 Universal Weld-on Hitch with Brackets # C99CR This hitch will fit that frame distance and produces a drop of 18 inches from the frame of your Isuzu. - Curt Class 5 Universal Weld-on...
  view full answer...
• Hitch Option For School Bus With 34 Inch Wide Frame
  The only option we have for a hitch for your school bus with a 34 inch frame is a weld on hitch: - Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop # 15901 This is for frames up to 44 inches wide and gives you the drop you need as well, so it will work out very nicely.
  view full answer...
• Option For Trailer Hitch For Holiday Rambler Motorhome
  There is possibly an option for a trailer hitch that fits your 2004 Holiday Rambler, and I say possibly because while a custom fit hitch is not available, there are universal weld-on hitches. This depends on the width of your frame from outside to outside, so if your frame measures up to 44 inches (from outside to outside), you can use any of the following. - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR - 18" Drop: Curt...
  view full answer...
• Recommended 10,000 lbs Capacity Hitch for a Motorhome
  I have a universal hitch that will fit your Gulf Stream and provide you with the needed 10,000 lbs towing capacity but it must be welded on. It is the Class V Universal Weld-on Receiver Hitch item # 15901. None of the bolt on hitches have a capacity higher than 5,000 lbs. I have linked the instructions below so you can take a look at the steps and understand the process.
  view full answer...
• Trailer Hitch for Ambulance on 2000 Ford E450 Cutaway Van Chassis
  We don't offer a custom hitch for the 2000 E450 Cutaway, because the configuration of the back bumper in regards to the frame members is different than the cargo van. You'll need a weld-on universal hitch, like part # 15901. The hitch has a 3 inch drop, which means that in order for it to fit on your ambulance, the vertical distance between the the underside of the frame member and the bottom of the bumper needs to be less than 3 inches, or the bumper will be in the way of the receiver...
  view full answer...
• What are the Towing Capacities for the Curt Hitches part # 15901 and # 15902
  I can tell you what Curt lists as the capacities for their # 15901 and # 15902 hitches. You are correct, they both have 12k capacities. The only other capacity you will need to look up is the capacity for your RV. If it is at least 12k then you could take full advantage of the hitch's capacity assuming they were installed correctly. This info should be in the RV owner's manual.
  view full answer...
  
• What Hitch do You Recommend for My Japanese 1992 Toyota Hilux?
  For your 1992 Toyota Hilux, we did have a neighbor that installed the Curt Trailer Hitch Receiver # 13086 on his Toyota Hilux model. I went ahead and attached a picture of the fitment of the hitch on his truck. However, I called Curt and my contact confirmed that there is no way of telling if that hitch will fit for sure on your 1992 Toyota Hilux. Also, as you can see in the attached picture, the hitch does not have the cleanest installation. With that being said, I recommend a universal...
  view full answer...
  
• Best Class V Trailer Hitch for a Class C Motorhome
  I do still have an option for you in the Class V Universal Weld-on Receiver Hitch part # 15901 but it sounds like you are looking for a custom fit trailer hitch and none of the trailer hitch manufacturers we offer custom fit them to motorhome chassis. Therefore, you will need to notify the above to work for you. It has a class v rating with adjustable brackets that will accommodate your motorhome with slight alterations. The low profile brackets will also provide you with the flush look...
  view full answer...
• Recommended Trailer Hitch for a 2010 Chevrolet Express Box Truck
  Kenneth, since you probably do not need as much drop as most you'd probably best benefit from a hitch that has minimal drop like the Curt Adjustable Trailer Hitch Receiver # C13701 that has 2" of drop or # 15901 for a 3" drop. Both of these hitches are semi-universal so they'll fit a range of frames, both have a 2" receiver opening, and are both assembled in the USA. The main difference other than the drop, is # 15901 is a class V hitch rated at 16K, and # C13701 is a class III hitch,...
  view full answer...
• Trailer Hitch Receiver Options For 1999 Ford E450 Ambulance
  The width of the mounting channel is 2-7/8 inches for the Draw-Tite Max-Frame Trailer Hitch Receiver # DT37GR. It's pretty unlikely this is going to fit, and for applications like yours, the best option is a universal hitch that you can weld on. So long as your frame is no longer than 44 inches wide from outside to outside, a universal hitch will work, you just need to measure how far down you need the receiver to be from the bottom of the frame (the drop). Once you know that, you can...
  view full answer...
  
• Trailer Hitch for a Champion Crusader Shuttle Bus
  For a Crusader Shuttle Bus, there is not a custom-fitted hitch, so a universal hitch will be the way to go. A good weld-on hitch is the Class V Curt, part # 15901. This has a 15,000-lb gross towing weight capacity and a 1500-lb gross tongue weight. It can fit frames between 18" and 43.88". Your shuttle bus does seem to have a large bumper, so you may want to look into a hitch with a longer receiver. Another Curt option is the RV hitch, part # 13703. This can be a bolt-on or weld-on hitch,...
  view full answer...
• Receiver Recommendation For a 2001 Dodge Ram 1500 With Roll Pan Rear Bumper
  As we do not carry a custom fit receiver option for behind the roll pan on your 2001 Dodge Ram 1500, I recommend having the Curt Universal Receiver # 15901 custom fit on your truck. This will allow you to have the receiver hidden behind the license plate on your roll pan which you will be able to remove and install with the Bracket # 5443 depending on if you are towing or not. This will also give you a much cleaner look than if you had one hanging below the roll pan on your Ram. You will...
  view full answer...
• Trailer Hitch for 2011 Mercedes-Benz Sprinter 3500 With 30-3/8 Inch Frame Width
  I have a solution for you but there are no custom fit hitches for the narrow 30 3/8 inch frame 2011 Mercedes Benz Sprinter 3500 Dually models. They weren't as widely produced and some have a service body or step bumper which obstructs where a hitch would be mounted. If your Sprinter has a step bumper you will need to remove it. Once that's done, you'd want to measure the drop needed. The drop is the vertical measurement from the underside of the vehicle frame member and the lowest point...
  view full answer...
• Trailer Hitch Options For A 2001 Blue Bird TC2000 Bus
  Hey Mike, Since there isn't a custom fit hitch for your bus you'll need to go with an adjustable fit weld on hitch. We offer a variety of drop lengths, which I've listed below, to help get the receiver tube at the right height: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...

Do you have a question about this Heavy Duty Receiver Hitch?