Will The Draw-Tite Trailer Frame Hitch Receiver Fit A 1974 Chevy K5 Blazer With A Gas Tank Shield
Published 06/22/2022
Products Featured in This Question
Question:
Will this trailer hitch fit a 74 K5 Blazer that has the OEM steel gas tank shield?
asked by: Jack G
Helpful Expert Reply:
The Draw-Tite Max-Frame Trailer Hitch Receiver 75129 should fit with any OEM parts but just to be used I went out to the warehouse and measured the hitch. From the back of the crossmember tube to the center of the first bolt hole is 1". The distance between the inside of both mounting ears is 30-1/4".
This hitch should sit directly under your frame rails so you can use that 1" measurement to see if the tube will run into interference with your gas tank shield.
If this doesn't work then you can go with the an adjustable-fit, weld-on hitch. You'll just need to determine the correct drop needed for the receiver tube to clear the bumper.
Draw-Tite
7" Drop # 41990-07
16" Drop # 41990-16
Curt
3" Drop # 15901
9" Drop # C47CR
10.865" Drop # 15902
11-1/2" Drop # 15903
18" Drop # C99CR
(click to enlarge)
Product Page this Question was Asked From
Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2"
- Heavy Duty Receiver Hitch
- Weld-On
- 44 Inch Wide
- 1600 lbs TW
- 16000 lbs GTW
- Class V
- 2 Inch Hitch
- 16 Inch Drop
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2"
- Shop: Roadmaster Anti-Rattle Hitch Extender for Tow Bars - 2" Hitches - 7-3/4" Extension
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide
- Article: Hitch Adapters and Extenders
- Search Results: service body hitch
- Shop: Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44" Wide
- Video: An In-Depth Look at the Curt Class 5 Universal Weld-on Hitch w/ Brackets
- Video: Let’s Check Out the Roadmaster Anti-Rattle Hitch Extender for Tow Bars
- Shop: Brake Controller
- Shop: Trailer Wiring
- Shop: Buyers Products Class 5 Service Body Hitch Receiver - 2-1/2"
- Shop: Draw-Tite 2-Ball Mount for 2" Hitches - 2" and 2-5/16" Balls - 16K - Black
- Video: What to Know About the Roadmaster Hitch Extender for Tow Bars
- Shop: Brophy Hitch Reducer and Extender - 2-1/2" to 2" Trailer Hitch - 7" Long
- Video: Let’s Check Out the Curt Class 5 Universal Weld-on Hitch w/ Brackets
- Video: All About the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Setting up the B and W Heavy-Duty Trailer Hitch Receiver on a 1988 Ford F-150, F-250, F-350
- Video: Setting up the B and W Heavy-Duty Trailer Hitch Receiver on your 1986 Chevrolet C/K Series Pickup
- Search Results: bwhdrh25122
- Q&A: Recommended Trailer Hitch Receiver, Trailer Wiring, and Brake Controller for 2002 Ford F-450 Chassis
- Q&A: Dimensions of Draw-Tite Ultra Frame Trailer Hitch Receiver # 41947
- Q&A: 2007 Ford E450 Super Duty Brake Controller and Install Harness
- Search Results: 41938
- Q&A: Hitch Recommendation to Fit Frame Width of 34 inches
- Q&A: Side to Side Measurements for B&W Class V Trailer Hitch # BWHDRH25122
- Q&A: Drop and Distance of Hitch Receiver on B&W Heavy-Duty Trailer Hitch Receiver
- Q&A: Can The B&W Heavy-Duty Trailer Hitch BWHDRH25122 Clear An Aftermarket Bumper On A 1986 Chevy K20?