Wire Loom - 100'

See what our Experts say about this Spectro Wiring

• Typical 7-Way Wiring Color Codes
  The wire loom part # 459075 does not actually have any wire in it, but it sounds like you are curious about the standard trailer 7-way wire colors. There are a couple variations, but for the most part the diagrams I attached show the most common trailer wiring colors.
  view full answer...
  
• What Is the Largest Wire Loom Available?
  3/4" is pretty large, the closest we have to 3/4" is the Wire Loom # 459075 which has a 1/2" diameter. This loom is 100', however if you would rather use by the foot you'd want # 459075-1 instead.
  view full answer...
• What Size Clamp to Use for 3/8" and 1/2" Size Wire Loom
  You should be able to use the same size clip as the inner diameter of the wire loom. For example, the 3/8" Diameter Wire Loom # 39035 has grooves in it that would allow you to use a 3/8" inner diameter clamp. Same thing goes for the 1/2" Wire Loom # 459075-1 or # 459075.
  view full answer...
• How to Install Tekonsha Prodigy P2 Brake Controller on a 2015 Volkswagen Touareg TDI
  The factory plug for installing the Prodigy P2 # 90885 on your 2015 Volkswagen Touareg TDI should be located under the vehicle's dash on the driver's side close to the door. You will need to acquire the following from your Volkswagen dealer to perform the install: 1 connector housing (#1J0-972-782) and 2 wire/terminal assemblies (#000-979-228). I have attached a photo of where the connector is located as well as a helpful article and an installation video of us installing the P2 with the...
  view full answer...
  
• Does Tekonsha 4-Pole Wiring Harness 118786 Fit 2018 Jeep JL Wrangler
  Tekonsha's Fit Guide confirms wiring harness # 118786 as a fit for your 2018 Jeep JL Wrangler. You can double-check before ordering if you like by comparing the included photo that shows one of the harness' custom connectors to the connectors at your Wrangler's tail lights. Installation should take about an hour or less and you can refer to the linked wiring installation article and video for guidance. I recommend adding protective wire loom # 459075-1 to your install; this is sold by...
  view full answer...
  
• Can Wire Loom be Used to Protect Wiring from Sun Damage
  Wire loom like the # 7509-10 that you referenced is a great way to help protect wiring. This kit is 10 feet long and 1/4 inch in diameter. If you need bigger we have 1/2 inch diameter loom sold by the foot as part # 459075-1.
  view full answer...
• Will the 1/2 Inch Metal Loom Clamps Work On a 5/16 Inch Frame Rail
  Yes, the Metal Loom Clamp part # A0500 will work on a trailer frame that is 5/16" thick. The Metal Loom Clamp will actually work on pretty much any frame thickness but you will need to make note of the size screw used. I recommend the Hex Screw part # 101131802 for a 5/16" thick frame as it is 1/2" long. The Wire Loom part # 459075 can then be added to protect your wiring. I have attached a list of our other wiring accessories for you below as well.
  view full answer...
• Can the Power Wire on Trailer Wiring Harness # 118498 be Routed Inside of a 2011 Toyota Sienna
  There are a couple of options for routing the power wire for Tow Ready Custom Fit Vehicle Wiring, # 118498. Since you want to keep it out of the elements, you can either route the wire through the frame or route it through the cab of the vehicle. If you want to route it through the frame, you will need a long and rigid piece of wire, push it through the inside of the frame from the front of the vehicle to the back, tie the power wire to the end, then pull the rigid wire back through. This...
  view full answer...
• What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire
  I would go with a 3/8 inch diameter, like # 39035. That should provide enough space for the wires and still give good coverage. This loom comes in a 10 foot length. If you needed less of expect that you might have other wiring to run with the existing wires, you can go to a 1/2 inch loom, sold in 1 foot increments, # 459075-1.
  view full answer...
• Compatibility Of 1/2 Inch Loom Clamps With 3/8 Inch Loom
  Yes, you can use Metal Loom Clamp - 1/2" # A0500 with Wire Loom 3/8" Diameter # 39035. It will secure the loom to your frame but it will not clamp tightly around it. If you want a tight fit at the clamps you can use 3/4" x 60' Electrical Tape to close the loom at that location and make it your desired thickness for clamping. If you want a perfect fit, I recommend the Wire Loom, 1/2" Diameter (per Foot) # 459075-1.
  view full answer...
• T-One Vehicle Wiring Harness for 2019 Jeep Wrangler Unlimited
  The Wiring Harness # 118416 that you are looking at is for the 2007-2018 Jeep Wranglers. For your 2019 Jeep Wrangler Unlimited you will need the Wiring Harness # 118786. The taillight connections are new for your Jeep. We do have a great video linked below of this harness being installed on your Jeep. I recommend getting some Wire Loom # 459075-1 and a Mounting Bracket # 18144 for a clean factory looking installation.
  view full answer...
• Installing Tekonsha Primus # TK90160 Brake Controller on 2014 Chevy Suburban
  The 2014 Suburban doesn't use a plug like the 2014 Silverado 1500 does, it will wire directly into the tow package wiring like the 2008-2013 GM trucks did. If you look at the FAQ article I've linked you to, you can see the Primus would wire up to the tow package wiring located under the dash. I've also linked you to an install video showing a controller being installed on a 2008 GMC Yukon. Although the vehicle is different, the install procedure would be just about identical. The wiring...
  view full answer...
• Black Molded Fender Bracket for Clearance Lights Not Long Enough for 10 Inch Wide Fender
  There isn't a longer version of bracket # A67BB but what you could do is use some wire loom, such as # 459075-1, to hide/protect the wire. Or you could likely find a small diameter plastic tube that you could cut in have (lengthwise) to get a semi-circle to extend the length of the bracket.
  view full answer...
• Recommended Wiring And Trailer Light Kit For Harbor Freight Trailer
  Since you said you want to re-wire your entire trailer I recommend the Optronics Submersible Trailer Light Kit, part # TL5RK. This kit comes with 2 stud-mount lights, 2 amber side marker and clearance lights, a license plate bracket, and a 25 ft wiring harness with a 4-way connector. The mounting hardware is also included with this kit. I have also attached a link to an installation video for this wiring kit you can check out.
  view full answer...
• Recommended Wire Loom for Parallel Multi Conductor Wire
  For the # SWC4332-1 you can use the Wire Loom, 1/2" Diameter (per Foot) # 459075-1. This is sold by the foot so you can get exactly what you need. Since I'm guessing you don't want to drill into your galvanized frame, I would try zip ties to keep it secure.
  view full answer...
• Can Steel Light Mounting Box be Used to Mount Lights High Up On a 2004 Sunseeker Motor Home
  You would be able to tell pretty quick if the walls can support the lights and housing with just screws. Otherwise some type of anchor would be required like you would use in drywall. The difficulty of running the wires to the desired location is going to depend on how much room there is behind the walls to route the wiring. Otherwise you could route it on the outside of the trailer and use something to protect the wires, like loom # 459075 painted to match the exterior of the trailer...
  view full answer...
• 2019 VW Volkswagen Atlas Trailer Hitch And 4-Way Wiring Harness
  The Curt Trailer Hitch Receiver # C13366 is a great option for adding a hitch to your 2019 Volkswagen Atlas although we don't have an etrailer branded hitch currently that is a confirmed fit for this vehicle. This hitch will do the job for you whether you're looking to carry bikes, additional cargo, or towing. The black gloss finish looks great and will help resist corrosion for a long life of use on your Atlas. Installing the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat...
  view full answer...
• Can 12V Source Other than Battery Be Used When Installing Trailer Harness On 2017 Lexus NX
  The problem with attaching the 12V hot wire to any 12V plug or accessory in the vehicle is that the plug you found may be on a circuit with another item in your Lexus. You really want to make sure the wiring harness is on a circuit by itself. That way it protect the vehicle electrical system if anything happens like damage or a short. There is an inline fuse with the # 118652 harness that protects the converter and the wiring. I do not recommend using any 12V source other than the battery...
  view full answer...
• Brake Controller Wiring Kit For Vehicle With 7 Way Already Installed
  We do offer the wiring kit # 5506 which will includes the wire, circuit breakers and connectors that come in the # ETBC7 kit. You can get a few feet of wire loom # 459075-1 and some zip ties. Since your vehicle already has the 7 way installed, that will be all you need.
  view full answer...
• Replacement Wire Loom to Secure RV Slide-Out Wiring
  Thanks for the photo, that was a huge help! You're needing 1/2 inch wire loom, which we sell by the foot as part # 459075-1. I'd also use some 1/2 inch loom clamps, part # A0500 to secure the wire loom and hold it where it's supposed to be.
  view full answer...
  
• What Size Wire Loom Is Recommended for Trailer 7-Way Wiring
  For a wire loom for 7-way wiring we recommend 1/2 inch diameter like part # 459075-1 that is sold by the foot. I have a 7-way adapter on my desk that has a wire loom on it that is 1/2 inch so I know this size would be correct.
  view full answer...
• Installation of Blue Ox Bulb and Socket Tail Light Kit on 2001 Honda CR-V
  The wiring can be ran through the vehicle interior if you wish, but doing so will triple or quadruple the install time and complexity. I do not have specific instructions regarding how to do this, but generally speaking you would need to use an existing opening in the firewall (or drill one if there is not an existing opening). The wire would run behind the side kick plate, and under the door thresholds to the rear cargo area. From there, it would run behind the side trim panel in the cargo...
  view full answer...
• Best Protective Wire Loom for Installing Cargo Carrier Light Kit 98174LED
  To install the cargo carrier LED Light Kit # 98174LED I suggest you use the 1/2-inch wire loom # 459075-1. This is the largest size we offer and it will make installation a bit easier. It is sold by the foot. Some extra zip ties # DW05724-10 might help too.
  view full answer...
• Are There Any Trailer 7-Way Cables With 6 or 8 Gauge Wire Available
  The trailer 7-way cables that we currently offer are going to max out at 10awg so you would need to get just the connector, like part # A7WCB, and wire it yourself with 8awg or 6awg. To protect the wires you can use some 1/2" wire loom # 459075-1 and wrap it all with electrical tape.
  view full answer...

Do you have a question about this Wiring?