Wire Loom 1/4" Diameter, 10' Long

Ask the Experts about this Spectro Wiring

• What is the Best Size Wire Loom for Bonded 4 Wire and One 12 Gauge Wire
  I would go with a 3/8 inch diameter, like # 39035. That should provide enough space for the wires and still give good coverage. This loom comes in a 10 foot length. If you needed less of expect that you might have other wiring to run with the existing wires, you can go to a 1/2 inch loom, sold in 1 foot increments, # 459075-1.
  view full answer...
• Is the Spectro 1/4 Inch Diameter Wire Loom Split
  The Spectro 1/4 Inch Wire Loom, # 7509-10, is split wire loom. All of the wire loom we sell is split.
  view full answer...
• Can Wire Loom be Used to Protect Wiring from Sun Damage
  Wire loom like the # 7509-10 that you referenced is a great way to help protect wiring. This kit is 10 feet long and 1/4 inch in diameter. If you need bigger we have 1/2 inch diameter loom sold by the foot as part # 459075-1.
  view full answer...
• How To Install a 7-Way Trailer Wiring Harness On a 2019 Subaru Ascent
  There are two different 7-way trailer wiring harnesses for a 2019 Subaru Ascent dependent on whether or not you have the factory tow package. If you do have the factory tow package then you should be using the Tekonsha OEM Replacement Vehicle Wiring Harness part # 118290, not the Universal Installation Kit for Trailer Brake Controller part # ETBC7. If you found a plug under the dash for the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 3062-P then you have the factory...
  view full answer...
• Custom 4-Pole Wiring Harness for 2019 Jeep Cherokee
  Curt 4-pole wiring harness # C56406 and the similar Tekonsha # 118779 will work fine on a 2019 Jeep Cherokee with or without the factory tow package being present. Both of these custom-fit kits plug in to the wiring at the tail lights and they will function correctly either way since they are wired independently of any tow package wiring. I recommend the Tekonsha kit because in our experience their wiring products are the most reliable. These harnesses feature a powered tail light converter...
  view full answer...
• Does Hot Lead on Wiring Harness for 2018 Jeep JL Wrangler Unlimited Have to be Run to Battery
  Thanks for the purchase and that is a good question, but you must run the hot lead directly to the battery when installing a 4-way, which in your case is the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56407. The reason is this is the only way to ensure your car's wiring is not otherwise affected, and you can run the hot lead from your battery in any manner you see fit. To do this you may need Wire Loom, 10' Long # 7509-10 and Loom Clamp -1/4" # A0250....
  view full answer...
• 4-Pole Wiring Harness Kits for 2016 Ford Transit T250 & T150
  The two 4-pole wiring harness kits you referenced, Curt # C56327 and Tekonsha # 118643, are confirmed fits on both the 2016 Ford Transit T150 and T250 if they do not have the factory trailer wiring setup. Installation for these two harnesses is essentially identical. Both have custom-fit connectors that plug in at your taillight wiring; both have a white ground wire that will attach to the vehicle metalwork; and both have a single power wire that you will need to run up to the engine...
  view full answer...
• Guidelines for Running Power Line to Front of Vehicle When Installing Powered Taillight Converter
  There is no one 'accepted' method for running that power wire to the battery. Our installers will usually try to follow existing wiring harnesses, or will choose the route that keeps the wire well protected. I don't have any video footage to show you, but I can link you to an FAQ article we've produced that will give you some good guidelines to follow. If the wire will be exposed, using some wire loom like part # 7509-10 will provide some additional protection. You can use zip ties to secure...
  view full answer...
• Parts Needed for Always-On 12V Circuit on 2018 Ford F-150 with Factory Wiring
  The 12V auxiliary power circuit in your Ford's 7-way wiring setup is unusual. This circuit becomes active once you press the brake. It will otherwise appear to be dead. So unless you are driving there will not be power on that 7-way contact. This decision by Ford has caused a lot of confusion for Ford owners. If you want your 7-way 12V circuit to be active at all times, regardless of the ignition key position or operation of the brake pedal, all you need to do is bypass the existing...
  view full answer...
• Recommended Wire Gauge and Related Parts to Install 12V Battery Charge Line on 7-Way
  We recommend at minimum a 14-gauge wire for providing 12V charging power to a towed vehicle's battery, such as that included in the Roadmaster Battery Charge Line Kit for Towed Vehicles, item # RM-156-25. Naturally, a heavier-gauge wire would do better since it can deliver more current. If you prefer you can use 10-gauge wire # 10-1-1, a 40-amp auto-reset breaker like # PK54540, ring terminals # 44-5310A and wire loom # 7509-10 to make your own kit. You can avoid tripping the breaker...
  view full answer...
• How Can Hot lead Wire Be Run When Installing Trailer Wiring Harness On 2016 Chevrolet Sonic
  Although we do not have a video showing the installation of the Curt T-Connector Vehicle Wiring Harness, part # C56303, on a Sonic, I have attached a helpful article that explains the different methods for running a hot lead wire to a vehicle battery. In most cases you can run the wire through a grommet to get the wire beneath the car. I understand running the power wire under the vehicle is not appealing but you can use wire loom like part # 7509-10 so the wire is protected under the...
  view full answer...
• Can a Trailer Be Pulled With a Faulty Breakaway System
  The trailer breakaway's are required in most states so I cannot advise for you to continue traveling without having the system repaired or replaced. It sounds like you have already identified the culprit (shorted wire) so what I recommend is just ordering a new system that way you can get it installed and hit the road again as soon as possible. The Pro Series Push to Test Breakaway Kit pprt # 50-85-315 is what I recommend for this because it is cost effective and easy to install. That said,...
  view full answer...
• Wireless and Wired Brake Controllers for 2019 Toyota Tundra with Factory 7-Way
  At this time (June 2019) we do not have any trailer brake controllers that offer under-dash plug-and-play installation in your 2019 Tundra with factory 7-way/4-pole. We do offer the no-wiring-needed Curt Echo controller # C51180 which requires only a working 7-way vehicle socket at the bumper and a compatible smartphone that serves as the display and control device. The Redarc Tow Pro Elite # 331-EBRH-ACCV2 can be installed in your 2019 Tundra but it will need to be hardwired. If you...
  view full answer...
• Does Hot Lead Need to be Run to Battery on 2011 Subaru Impreza Wagon
  The type of battery you described is not something you will be able to use to install the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM11143894 on your 2011 Subaru Impreza Wagon You need to run a hot lead to the battery because this is the only way to ensure your car's wiring is not otherwise affected. To do this you may need Wire Loom, 10' Long # 7509-10 and Loom Clamp -1/4" # A0250. I have added a link to a help article on routing a power...
  view full answer...
• Can Power Extension Cord for LED Light Strip Be Concealed with Wire Loom
  While we don't offer the # DG52673PB in black we do have wire loom like part # 7509-10 which is black that would protect and conceal the wiring like you are wanting. This would be an easy solution and is sold in 10 feet long sections.
  view full answer...
• Wire Loom and Wire Loom Clamp for Routing Power Wire for 7-way install on a 2003 Subaru Forester
  You are on the right track with all of the products you are planning on purchasing to install the Prodigy RF brake controller part # TK94FR and then also leave the option to use a different brake controller in the future. For wire loom I would go with 1/4 inch loom like part # 7509-10 sold in 10 foot sections, and then to secure the loom you could either use zip ties (this is what I did on my car) or you could use the Metal Loom Clamp # A0250 for a more permanent solution.
  view full answer...
• Wiring Kit Recommendation For 2009 Volkswagen EOS
  For your 2009 Volkswagen EOS the Tow Ready Wiring Kit part # 119190KIT is a confirmed fit. This kit includes the powered powered converter with circuit protection to safeguard your Volkswagen Eos wiring and the module. This kit includes everything necessary to hardwire it to your Eos. It also includes a circuit tester that is used to help find wires behind Eos taillights to determine signals. In the kit 20 ft of 12 gauge wire is included for the battery connections. The 12 gauge wire we...
  view full answer...
• RV has 7 Way and Need to Connect 4 Way for Dolly and 4 Way for Tow Lights to Use at the Same Time
  I have a solution for you. We do not have any type of Y adapter but I do have the parts available to allow you to connect both 4 wire flat plugs at the same time. I do recommend that you first check to ensure that you will not be drawing too many amps on the circuit by using both the dolly wiring and the tow lights together. You will need the following products: Car and Trailer End Loop, # 9653P Qty 2 Pollack 7-Pole Trailer Connector, # PK12706 Qty 1 First you will start by cutting...
  view full answer...
• Running 12V Wire from Battery to Wiring Harness
  On your 2009 Dodge Grand Caravan, I am not aware of any 12V power that will be adequate for the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM11142175 installation. If you are concerned about the wire rubbing on the frame you can use wire loom like # 7509-10. I've attached an article to assist with routing the power wire to assist.
  view full answer...
• Converting a 5 Pin Trailer Connector on a Motorcycle To a 4-way Flat on Trailer
  I have a solution for you, however we do not currently carry a vehicle 5-way to a trailer 4-way adapter. In order to connect your motorcycle to your trailer, you will want to create an adapter. To provide your trailer with a 4-way flat connector, you will want to use the Tow Ready Upgraded Circuit Protected Taillight Converter # 119178. The wires that come out of the harness's converter will be connected to a 5-way trailer connector. If the 5 pin on your motorcycle is round, you...
  view full answer...
• Parts Needed to Install Always-On 12V Power Circuit on 2018 Ford Super Duty
  Ford did decide to change the operation of the 12V auxiliary power circuits on newer trucks. The fix for this annoying circumstance is easy enough. All you need to do is bypass the existing 12V circuit with a new direct battery connection that will allow the 7-way to have active 12V power at all times, regardless of the ignition key position or operation of the brake pedal. You will need just a few parts to accomplish this: circuit breaker # PK54540, 10-gauge wire # 10-1-1, ring terminals...
  view full answer...
• Testing Trailer Brake Circuit and Replacing Brake Output Wire on 2013 Ford F-350
  Since your issue with the trailer brake circuit began with a big bump I would first check the wiring at the 7-way. That bump may have been a pothole but it could also have been a bit of road debris that may have damaged that wire. Essentially you'll want to inspect the truck wiring from the 7-way socket, forward as far as you can trace it. Look for damage to the insulation, cracks or worn spots. Look for points where the brake wire may be touching suspension components or any sharp...
  view full answer...
• Tips for Routing Trailer Wiring Harness Power Wire to Battery on a 2011 Kia SOrento
  Wire loom is not necessary but it can be used to protect the wire. You can get a 10 foot long section # 7509-10. You would likely need more than 10 feet though. Routing the wire on any vehicle is a matter of preference. There are basically 3 ways to do it: under the vehicle exposed, under the vehicle not exposed or partially exposed, and through the vehicle interior. I have included a link to the right to a help article I wrote with tips on routing the power wire.
  view full answer...
• No-Splice Plug-In 4-Pole Trailer Wiring Harness for 2008 Lincoln MKX
  We do offer both hard-wire and custom plug-in 4-pole wiring harnesses for the 2008 Lincoln MKX. The unit I recommend for your MKX is the custom plug-in harness from Tow Ready, part # 118551. This trailer wiring harness installs by plugging in to your MKX's tail light wiring; just one spliced connection is required, for the 12V power input wire to the converter. (Note that for the MKZ you can instead use harness # 118502 that installs in the same manner.) This connection is made from...
  view full answer...
• Product to Protect Trailer Wiring on 2007 Suzuki Grand Vitara
  It is a great idea to provide some protection for your trailer wiring on your 2007 Suzuki Grand Vitara and we do offer a product just for this purpose. Wire loom is offered in 10-foot lengths in both 1/4-inch diameter (part # 7509-10) and 3/8-inch diameter (part # 39035) and also in 1/2-inch size by the foot, part # 459075-1. The linked video shows an application of this product. Wire loom is a great idea in general, but especially in cold climates where winter time road salts can attack...
  view full answer...
• Does Hot Lead Have to be Run to Vehicle Battery
  You can only run a hot lead to the vehicle battery when installing a trailer wiring harness like the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM11143894 on a 2011 Subaru Impreza Wagon. You need to run a hot lead to the battery because this is the only way to ensure your car's wiring is not otherwise affected. To do this you may need Wire Loom, 10' Long # 7509-10 and Loom Clamp -1/4" # A0250. I have added a link to a help article on routing a...
  view full answer...
• What Wiring to Use to Install Electric Trailer Brakes
  Trailer axles do sometimes include a wire for an electric trailer brake circuit to make it easier to route power to each of the brake assemblies. We have suitable 10-gauge brake circuit wiring, part # 10-1-1, that can be ordered by the foot. This wire has blue insulation which is the color usually associated with trailer brake wiring. Electric trailer brakes use a 2-wire hookup. Either wire from the brake can be used as ground or hot; since these wires are non-polarized it does not matter...
  view full answer...
• Is a Trailer Wiring Converter Needed for a 2011 Jeep Liberty
  Yes, a converter is needed for a 2011 Jeep Liberty because one the tail light circuits are on separate wires and they need to be combined for a trailer and two the factory tail light circuits are not sufficient to power the lights on a trailer as well as the lights on the vehicle. I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118554 which has one of the most durable converters on the market due to the potting which helps keeps the wires attached...
  view full answer...
• Troubleshooting Trailer Wiring Harness That Instantly Blows Fuse When Connecting to Battery
  The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118502 having a spark as well as blowing a fuse is a sure sign that the ground is not connected properly or the power wire at some point is touching a metal ground. I recommend tracing that power wire to ensure there is no insulation missing where it could be touching metal. You can see with our installation of this wire we used wire loom # 7509-10 in some areas to assist with areas that have sharp edges. If you need...
  view full answer...

Do you have a question about this Wiring?