See what our Experts say about this CURT Trailer Hitch Ball Mount

• Is it Better to Go with Higher or Lower Rise Ball Mount than Needed
  You've got good instincts. I recommend going with a ball mount that has a 2 inch rise for the exact reason you mentioned, the truck will settle a bit with the tongue weight and any cargo weight. The ball mount we offer with a 2 inch rise is the Curt Class III Drawbar # C45270. This is considered an extra long ball mount, measuring 13 inches from the hitch pin hole to the ball hole. Another option is the Curt Ball Mount for 2 Inch Hitches - Angled Shank # C45230. This ball mount has...
  view full answer...
• Availability of Ball Mount in Rise Position with Pre-Torqued Ball
  Hey Tom, I wish we had a way to do that but we don't have an option to order the Draw Tite ball mount # DT49MR pre-torqued in the rise position but we do have some similar options: etrailer ball mount part # e38NR with a rise of 2-3/4inches Curt # C45155 rise of 2-1/4 inch Curt # C45152 rise of 2 inch
  view full answer...
• What Hitch Fits a 2013 Volkswagen Jetta SportWagen TDI
  Hey John, thanks for reaching out! The Curt Trailer Hitch Receiver # C11474 will not fit your 2013 Volkswagen Jetta SportWagen TDI. Instead, you need to use the EcoHitch Hidden Trailer Hitch Receiver # 306-X7284 because it's the only one to fit with the TDI model. If you're needing a ball mount with a smaller 1-7/8" hitch ball (there aren't any 1-1/4" hitch balls) then something like the Curt Fusion Ball Mount # C45152. To complete a towing setup, you also need the Curt Wiring Kit #...
  view full answer...
• Recommended Parts Needed to Tow with a 2019 Ford Flex
  The trailer hitch that I recommend using to tow a small trailer with your 2019 Ford Flex is the Draw-Tite Max-Frame # 75679 which is a confirmed fit for your vehicle. Then for wiring I recommend the Tekonsha T-One # 118472 because it has the highest amp draw rating out of the available options. This means that if you end up towing a trailer with a fair amount of lights on it you won't overdraw this wiring harness. If you would like to mount this near the receiver then you can use the mounting...
  view full answer...
  
• Recommended Ball Mount for Towing 5x8 Rental Trailer With 2020 Toyota Highlander
  The U-haul 5x8 trailer has a maximum GVWR (maximum recommended weight of trailer plus contents) of 2700 lbs. The trailer's tongue weight, which could be anywhere from 100 to 400 or so lbs will cause the rear suspension of your Highlander to squat to a certain degree. I'd go with a ball mount that provides a 2 inch rise to account for the anywhere between 1-3 inches of squat you'll experience. This will leave the trailer close enough to level that everything will work fine. We offer the...
  view full answer...
• Trailer Hitch Recommendation for 2017 Jeep Patriot
  For your 2017 Jeep Patriot, I highly recommend the etrailer Trailer Hitch Receiver # e98836 because it's super easy to install, offers a superior matte black powder coat finish to protect it from rust and corrosion, and its 4,000 lb tow rating is more than enough to safely tow your wave runner to and from the lake as often as you'd like. If you don't already have the rest of the towing components, I'll list my recommendations below: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole...
  view full answer...
  
• Hitch And Wiring For A 2010 Mazda CX-7.
  For your 2010 Mazda CX-7 I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # 75512. This hitch offers a 2" x 2" receiver tube opening. Having the 2" x 2" receiver tube opening rather than the 1-1/4" allows you to use the hitch for a lot of different accessories. With the 1-1/4" you would be limited to certain hitch mounted accessories. It also has a pre-welded bracket so when you install your wiring if you wanted to route it outside the vehicle...
  view full answer...
• Will Curt Fusion Ball Mount Work for Towing Lawn Care Trailer With 2000 Lexus RX 300
  You can use the Curt Fusion Ball Mount # C45152 to tow your lawn care trailer with your 2000 Lexus RX 300. The only reason you wouldn't be able to use it is if you don't have a 2" trailer hitch receiver like the # e64KR on your vehicle. This ball mount uses a 1-7/8" ball. If you need a 2" ball instead then you would need the # C45155
  view full answer...
• Class 3 Ball Mount With 2 Inch Rise and 1-7/8 Inch Hitch Ball for 2 Inch Receiver
  We carry exactly what you need with the Curt # C45152. This is a Class III ball mount that fits in 2 inch receivers, has 2 inches of rise and a 1-7/8 inch hitch ball. It comes with a pin and clip, and has a gross towing capacity of 5,000 lbs with a tongue weight capacity of 500 lbs. I've added a link to a video review of this part for you to take a look at as well.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?