Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…
A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…
I sure can Blake! I just heard back from Dexter and both of your axles are 3,500 lbs capacity. That's all the information they were able to provide. Here are the replacement parts you've requested: Hub/Drums - 5 on 4-1/2 Lug Nut Pattern item…
Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…
In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.
Hey Darren, the studs of the Optronics Fusion LED Trailer Light #OPT45KB that you referenced are not designed to thread out of the assembly easily. You could take a cutting wheel to them and cut them off flush pretty easily though if you wanted to…
We do offer a wide variety of replacement lights for trailer but since trailer manufacturers don't keep a record of what they use on trailers I would need some pictures of the lights you are wanting to replace along with some measurements so I…
Hey Sal, the Optronics Fusion LED Trailer Light #OPT45KB is for just 1, not set of 2. These are super nice, but if you want some other options to consider, we also have the Fusion LED Hardwired Trailer Light #OPT57NR which does have the same…
No, it is not plug and play Paul but it can be. The TecNiq Contoured Seven Function Box Style Tail Light item #TN62XR passenger side and item #TN42XR driver's side use a 3-Prong PL-3 Plug like item #TN47PV. These lights measure 7-1/2" long x…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
Hello John, thanks for reaching out. Yes, the mounting holes on the TecNiq Contoured Seven Function Box Style Tail Light #TN42XR (driver side) and #TN62XR (passenger side) are exactly the same as the Wesbar 271595 tail light. They are 2" apart…
Get a factory-style look and bright LED visibility with amber trailer lights from Command Electronics. Options include clearance or side markers in oval 4" x 1-1/2" x 1/2" or round 3" sizes, with hole spacings like 2-1/2" or 3" on center, so a quick, simple swap is easy when your measurements match.
Yes, installation is generally straightforward. Plan wiring and mounting, and test the light before finalizing. Some do not include screws, so have stainless screws on hand. If you prefer, swap factory clamp connectors for wire nuts. Add a gasket or sealant at the mounting surface to help with waterproofing.
Yes, on models with both turn and running functions you can cap the running light lead and use turn plus ground only. Verify your light has 3 wires and follow the wiring diagram. Confirm the function listing—RUN and TURN—so you get the behavior you want. Test the circuit before final mounting.
Measure your current light and the distance between mounting holes, then compare to the listed dimensions. Confirm the shape and profile match your opening so the lens and base sit flush. If you're adding side markers, plan wire access and visibility. Matching diode count helps keep the look consistent with your other markers.
They can be an exact match when your OEM lights are Command Electronics. Check the brand marking on your originals, then compare dimensions and mounting hole spacing to confirm a direct swap. If you want the same appearance, match the diode count. Some installs line up with existing holes; verify orientation before sealing.
Clearance Lights
Tail Lights
Filters
