Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
2-1/2" Round. Trailer light with reflector functions as a clearance and side marker light when properly mounted. Durable polycarbonate base and lens. Mounts on surface of trailer - hardware not included. 2-Wire pigtail. PC rated.
Features:
Specs:
A PC-rated light produces a 90-degree angle of light to either side of its centerline for a total of 180 degrees of coverage. This beam pattern can be clearly seen when you are standing directly in front of the light, as well as when you are standing on either side of the light. When properly installed, this type of light can function as both a front clearance light and a side marker light or as a rear clearance light and side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today, we're taking a look at a LED clearance or side marker light with a built-in reflex reflector. This round trailer light functions as both a clearance light and a side marker light when properly mounted. It is an LED system. LEDs make great replacements for incandescent lights. They last longer, burn brighter, and they're much more efficient. With LEDs, you don't have to worry about replacing bulbs or worry about brittle filaments.The unit features the really nice amber lens with the built-in reflex reflector.
It mounts on the surface of the trailer. You have three mount holes right there. You can gain access to those by removing the lens from the base. Mounting hardware for installation is not included. It's a two-wire pigtail, so the white wire is the ground wire, yellow wire is the power wire.
Now, the installation surface does require at least a 5/8" diameter hole for the wire base to fit into for a flush mount design. It is SAE approved, and it is a P2PC rated light.Taking a look at the dimensions real quick, starting with the overall diameter. Measuring edge to edge, that gives us a diameter measurement of about 2 1/2". The thickness of the unit, from the back of the base, right here, to the front of the lens, measures about 1" thick or 1" deep. That's how far it sticks out from the installation surface.
The distance we have between each mount hole, center on center, is 1 5/8".We're going to go and hook it up to power. That way you can see what it looks like with some power running to it. We'll also be able to turn off our overhead lights, so you can see it in a lower light setting. You can see here that the light sends out a nice consistent signal. You can see that built-in reflex reflector.
This light features a total of two diodes or two LEDs, so the multi-diode design really helps optimize the overall light output.That's going to do it for today's look at the LED clearance or side marker light with the built-in reflex reflector.
Average Customer Rating: 4.9 out of 5 stars (48 Customer Reviews)
2-1/2" Round. Trailer light with reflector functions as a clearance and side marker light when properly mounted. Durable polycarbonate base and lens. Mounts on surface of trailer - hardware not included. 2-Wire pigtail. PC rated.I am happy with the amber lights as a good match, but I was surprised they are upside down regarding aligning with the three holes for the installation screws. The light assembly and the lens both indicate which part is "up", but this does not match the original configuration. An obvious solution was simply to turn both "upside down" so the screw holes would line up. My only concern with this was there might be more potential for the amber lens cover to either pop off from vibration or to allow some moisture into the fixture when it rains (because the part you pry up to open the lens is now on the top rather than the bottom). I am going to put a bit of clear sealant at the top of the lens (which will not be visible from below).
Hey, Kimberly. So good to hear from you. I'm not a large volume customer, but when I need something, I need it! Yes, I am extremely pleased with the service I receive from eTrailer.com I placed this order just three days ago, received my order, and installed the clearance light this afternoon. The replacement light was a perfect fit...no installation holes to be drilled, wiring was so very, very easy. I must admit but I did view the installation video provided. As so usual, eTrade.com is my first choice in camper replacement parts.
Perfect replacement for my old school marker lights. Lens matches original
Light was a perfect match for the lights on my Camper. With so many light styles and color temperatures shopping for a match can be very difficult. etrailer.com is my go to for my lighting needs. I’ll be looking to them for my other trailer needs and will give a review on them in the future.
Needed replacement marker lights for a 2015 Itasca motor home. These are exact matches, fit perfectly.
The guy on the phone was very helpful and patient while I got more info. The lights were EXACTLY what the needed.
These are the identical replacements needed for the trailer.
exactly what I was looking for and received it very quickly!
Eric B.
2/10/2022
Well it’s been a year and still looks and works like brand new. I would buy it again when needed. Excellent light replacement for my new camper. Ez to install
Only place that had exact part I needed. thanks
Just what I need to replace a burned out light.
Quick shipment. Exact part I needed.
Best customer service ever? You guys Ro ck...
I’ve bought several items and pleased with ever purchase. Very timely deliveries and all ahead of stated delivery date quoted. I will buy again from etrailer.
Thank you etrailer.com
The light is just fine. I did expect white LED in it vs. amber but it's okay. I didn't see white LED specifically mentioned.
Perfect replacement for the original light on my trailer that failed.
It was exactly what I needed to match the other lights on the trailer!
Was exactly what I needed for 2016 motor home
Great light. The base needs to be white to match. But the light works..
very quick delivery time for standard s hipping.
Good durability, easy to install, good price to value ratio. Bulbs are quite bright.
Perfect fit. Shipped quickly and arrived as described.
Me gustaría que tuvieran servicio en Es pañol
Exactly what I expected, fast shipping
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Chantell
11/15/2023
STILL WORKING GREAT!!!!!!!