3-3/4" x 1-3/4". Trailer light with reflector functions as a clearance or side marker light. Durable polycarbonate base and lens. Mounts on surface of trailer - hardware not included. 2-Wire pigtail. P2 rated.
Features:
Specs:
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're taking a look at a LED clearance or side marker light with a built in reflex reflector. This small rectangular trailer light functions as both a clearance light and a side marker light when properly mounted. It's an LED system. LEDs make great replacements for incandescent lights. They last longer, they burn brighter, and they're much more efficient. With LEDs, you don't have to worry about replacing bulbs or worry about brittle filaments.
This unit features an amber lens, again, with the reflex reflector built it. It mounts directly on the surface of the trailer. Mounting hardware's not included. To gain access to the mount holes, you just need to remove the lens. You can do that by placing a flat blade screwdriver direction in here on either side, there's a little spot for it, and then just prying the lens off.On the back, you can see it's a two wire pig-tail, so we have our power wire and our ground wire.
White is for ground, yellow is for power. This is SAE approved, and it is a P2 rated unit. Taking a look at the overall dimensions, starting with the overall length, edge to edge measures three and 7/8 inches. Edge to edge going this direction, is one and 7/8. And the overall depth from the front of the lens to the back of the housing right here, you get a measurement of about 13/16 of an inch deep.The mount holes on the unit are separated on center by three inches.
We're gonna go ahead and hook it up to power, that way you can see what it looks like with some power running to it. And we'll also be able to turn off our overhead lights, so you can see it in a low-light setting. So here you can see the light sends out a nice consistent signal. You can really see that reflex reflector that's built into the lens. When it comes to the number of LEDs, that's a two-diode system or a two-LED system, so the multi-diode design really helps optimize the overall light output.And that's gonna do it for today's look at the LED amber clearance or side marker light with the built in reflex reflector..
Average Customer Rating: 4.9 out of 5 stars (28 Customer Reviews)
3-3/4" x 1-3/4". Trailer light with reflector functions as a clearance or side marker light. Durable polycarbonate base and lens. Mounts on surface of trailer - hardware not included. 2-Wire pigtail. P2 rated.Great experience. Fast shipping and communication. Would buy from again. A++
I needed blinker lights on the front of my '50 IH pickup. These replaced the parking lights. Works great!
Very good light, great customer service.
Just what I needed. A perfect fit!
I ordered a Command LED amber side marker light, K-58LB, to replace a like one on my 2017 Coachmen Freelander Class C motorhome. It's an exact replacement. E-Trailer price was about average but their low shipping cost brought the total price way down below all the other online businesses. E-trailer shipped it first class and I received it in 4 days total, including the weekend. E-trailer has always been my online first stop for RV parts.
Your company provided exactly the repair parts I needed for my Curt hitch. Was also time to change the red or yellow clearance lights on my motorhome. You had exactly what I needed. Parts arrived quickly and I've already installed them. Thanks for your help.
I got these LED marker lights to replace my old light bulb marker lights. They were just what I ordered and received them with in a weeks time.
Just like factory
Installed this today and it works perfectly. Was very pleased with the price and delivery timing from etrailer,com.
easy to order and fast delivered
easy to place orders and fast delivered
thanks again
Quick shipping and product was installed today and works great. I will ordered from you guys again soon, thanks!
Direct replacement and very easy to install. They look great.
Fast delivery, reasonable price, Exact replacement (and as advertised), fast install. Happy with purchase experience.
good value
Great product, great price and great company. Will definitely come back.
Everything was perfect when it arrived
Thanks!!
Product was delivered on time and in great condition
Thank you
Great item. Didn’t realize it was LED. PLEASANTLY SURPRISED. PERFECT fit.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.