Good question, Todd! I looked at some pictures we have of the Curt #C37RV hitch installed on a 2024 Hyundai Santa Fe and I think I found a good way to do it. Take a look at the picture I have included and you will see what I am thinking (circled in…
Hello Robert, Thank you so much for attaching the pictures, they’re always so helpful. In the first photo, it looks like your shackle straps are sitting a bit too vertically. That’s not a major issue, but since you’ll be replacing some suspension…
Hey there Caleb! Both the 2 inch and 2-5/16 inch balls supplied with the #WS97WR (adjustable 8" drop) fall under the same 22,000-lb hitch rating. Just make sure the ball matches your trailer coupler size, and always go by the lowest-rated part…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey McClaskey, since that is a rarer wheel bolt pattern we don't have any aluminum wheel options that match what you need. Instead our best option would be the Kenda Karrier #KR53 part #KE42EV which is a silver steel wheel with a ST205/75-15 tire…
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
Hey Terry, you’re likely not doing anything wrong. The Force #PA96VR has wide 6-1/2” tires that give great traction, but they don’t pivot sharply. For tight angle turns, it helps to alternate between forward and reverse, “walking” the tongue in…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
I do have a potential solution for you, but I do not have a 7 way harness that will plug in to the round plugs you described. I recommend using a pre-wired connector like part #20023. You will have to do a bit of cutting and splicing, and this kit…
Good question, Todd! I looked at some pictures we have of the Curt #C37RV hitch installed on a 2024 Hyundai Santa Fe and I think I found a good way to do it. Take a look at the picture I have included and you will see what I am thinking (circled in…
Hello Robert, Thank you so much for attaching the pictures, they’re always so helpful. In the first photo, it looks like your shackle straps are sitting a bit too vertically. That’s not a major issue, but since you’ll be replacing some suspension…
Hey there Caleb! Both the 2 inch and 2-5/16 inch balls supplied with the #WS97WR (adjustable 8" drop) fall under the same 22,000-lb hitch rating. Just make sure the ball matches your trailer coupler size, and always go by the lowest-rated part…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey McClaskey, since that is a rarer wheel bolt pattern we don't have any aluminum wheel options that match what you need. Instead our best option would be the Kenda Karrier #KR53 part #KE42EV which is a silver steel wheel with a ST205/75-15 tire…
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
Hey Terry, you’re likely not doing anything wrong. The Force #PA96VR has wide 6-1/2” tires that give great traction, but they don’t pivot sharply. For tight angle turns, it helps to alternate between forward and reverse, “walking” the tongue in…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
I do have a potential solution for you, but I do not have a 7 way harness that will plug in to the round plugs you described. I recommend using a pre-wired connector like part #20023. You will have to do a bit of cutting and splicing, and this kit…
Wire protection is essential for ensuring the safety and longevity of your electrical projects. Whether you're rewiring a trailer or securing connections, these products offer robust solutions for clamping, holding, and sealing wires effectively.
Wire protection is crucial for trailer rewiring, providing a secure seal that prevents electrical issues. Products like shrink tubing ensure watertight connections, enhancing the durability and safety of your trailer's wiring system.
Yes, wire protection products are versatile and can accommodate various wire gauges, such as 14-10 gauge wires. This flexibility makes them ideal for covering splices and ensuring a neat, secure installation.
Using wire protection in electrical projects offers several benefits, including preventing electrical shorts, protecting against environmental damage, and ensuring a clean, professional finish. This leads to fewer maintenance issues and a longer lifespan for your wiring.
Wire protection improves safety by creating a barrier against moisture and contaminants, reducing the risk of corrosion and electrical shorts. This is especially important in outdoor or exposed environments, where connections are more vulnerable.
Absolutely! Wire protection products are designed for easy installation, making them perfect for DIY enthusiasts. With straightforward application methods, such as heat shrinking, you can achieve professional results without specialized tools.
Filters
