Good question, Todd! I looked at some pictures we have of the Curt #C37RV hitch installed on a 2024 Hyundai Santa Fe and I think I found a good way to do it. Take a look at the picture I have included and you will see what I am thinking (circled in…
Hello Robert, Thank you so much for attaching the pictures, they’re always so helpful. In the first photo, it looks like your shackle straps are sitting a bit too vertically. That’s not a major issue, but since you’ll be replacing some suspension…
Hey there Caleb! Both the 2 inch and 2-5/16 inch balls supplied with the #WS97WR (adjustable 8" drop) fall under the same 22,000-lb hitch rating. Just make sure the ball matches your trailer coupler size, and always go by the lowest-rated part…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey McClaskey, since that is a rarer wheel bolt pattern we don't have any aluminum wheel options that match what you need. Instead our best option would be the Kenda Karrier #KR53 part #KE42EV which is a silver steel wheel with a ST205/75-15 tire…
Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
Hey Terry, you’re likely not doing anything wrong. The Force #PA96VR has wide 6-1/2” tires that give great traction, but they don’t pivot sharply. For tight angle turns, it helps to alternate between forward and reverse, “walking” the tongue in…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
Hey David, welcome back. To add a 4-way connector to your 2025 Kia Sportage PHEV, you'll want the Curt item #C99DR. It connects directly behind the rear tail lights and there isn't a way to connect it to a tow package. It will not control a…
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
Good question, Todd! I looked at some pictures we have of the Curt #C37RV hitch installed on a 2024 Hyundai Santa Fe and I think I found a good way to do it. Take a look at the picture I have included and you will see what I am thinking (circled in…
Hello Robert, Thank you so much for attaching the pictures, they’re always so helpful. In the first photo, it looks like your shackle straps are sitting a bit too vertically. That’s not a major issue, but since you’ll be replacing some suspension…
Hey there Caleb! Both the 2 inch and 2-5/16 inch balls supplied with the #WS97WR (adjustable 8" drop) fall under the same 22,000-lb hitch rating. Just make sure the ball matches your trailer coupler size, and always go by the lowest-rated part…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Hey McClaskey, since that is a rarer wheel bolt pattern we don't have any aluminum wheel options that match what you need. Instead our best option would be the Kenda Karrier #KR53 part #KE42EV which is a silver steel wheel with a ST205/75-15 tire…
Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
Hey Terry, you’re likely not doing anything wrong. The Force #PA96VR has wide 6-1/2” tires that give great traction, but they don’t pivot sharply. For tight angle turns, it helps to alternate between forward and reverse, “walking” the tongue in…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
Hey David, welcome back. To add a 4-way connector to your 2025 Kia Sportage PHEV, you'll want the Curt item #C99DR. It connects directly behind the rear tail lights and there isn't a way to connect it to a tow package. It will not control a…
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Dive into the world of soldering with reliable tools that make your projects shine. Whether you're fixing electronics or crafting new gadgets, these tools are designed to deliver precision and ease. Enjoy the convenience of handy designs and durable materials that ensure your soldering tasks are a breeze.
A reliable soldering tool offers consistent heat, a comfortable grip, and durable construction. Look for tools with adjustable temperature settings and a sturdy design to handle various tasks. Handy features like a cracked-resistant tube can enhance usability without affecting performance.
Soldering tools with precise heat control and ergonomic designs ensure clean, strong joints, reducing the risk of damage to components. A well-designed tool can make your work more efficient and enjoyable, allowing you to focus on creativity and precision.
While most tools perform well, some may arrive defective or with minor cosmetic issues like cracked tubes. These don't usually affect performance, but it's good to check for any defects upon arrival to ensure you have a fully functional tool for your projects.
Prioritize features like adjustable temperature control, a comfortable grip, and a durable build. A handy design, such as a tube for easy storage, can also be beneficial. These features ensure your tool is versatile and reliable for various soldering tasks.
High-quality soldering tools streamline your workflow by providing consistent heat and ease of use. This efficiency allows you to complete projects faster and with greater accuracy, making them an essential part of any electrical toolkit.
Filters
