Product Experts Available Now!
Call 1-800-940-8924
etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 15-3/8" Lift - 2,500 lbs
(1142 reviews)
Price: $150.08
In Stock
We'll connect you with nearby partnered installers who know this exact setup.
etrailer Boat Trailer Jack w/ Footplate - Sidewind - Fixed Mount - 15-3/8" Lift - 2,500 lbs
Part Number: MJSQ-2500B
In Stock
$150.08
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
We'll connect you with nearby partnered installers who know this exact setup.
- All Info
- Reviews (1142)
- Q & A (0)
- Photos
etrailer Trailer Jack - MJSQ-2500B
Highlights
- 2,500-Lb Lift Strength: Handles heavy loads for secure support on large or loaded trailers.
- 29-1/8" Total Adjustment: 15-3/8" lift plus 13-3/4" drop leg adjustment gives plenty of height range.
- Stable Footing: 7-1/2" x 3-3/4" footplate spreads weight to prevent sinking on soft ground.
- Rust-Resistant Build: Clear zinc finish and steel body stand up to water and road salt.
- Smooth Sidewind Crank: Offset 7-7/8" handle radius keeps hands clear for easy raising.
- Bolt-On Ready: Mounts to frames up to 5" tall x 3" wide with included 3/8" hardware.
Features to know about
Smooth Setup Anywhere: Drop Leg Gives You Quick Height Adjustment
Getting your trailer leveled or lifted doesn’t have to mean endless cranking. This etrailer Boat Trailer Jack combines 15-3/8" of lift with 13-3/4" of drop leg adjustment for a total adjustment of 29-1/8". Just pull the pin to drop the leg, and you’ve already made up most of the distance to the ground. The 7-1/2" long x 3-3/4" wide footplate spreads weight evenly and keeps the jack from sinking into soft ground. It’s a big upgrade from wheeled jacks that twist or roll when parked on dirt.
Built to Last: Clear Zinc Finish Fights Corrosion
Rain, salt spray, and road grime are no match for the clear zinc finish on this jack. It’s designed to resist rust and corrosion, even in harsh marine use, with a 100-hour salt spray rating. Heavy-duty steel construction keeps it solid for years of use, and the square tube design adds rigidity where round tubes can flex. Reviewers using it daily around saltwater ramps noted it stayed smooth and dependable well past the first season.
Easy Cranking That Feels Effortless: Sidewind Handle With Grease Zerk
The side-mounted handle gives you room to turn without scraping your knuckles on the trailer frame. Its 7-7/8" handle radius provides smooth leverage, and the built-in grease zerk makes maintenance simple—just a few pumps when the handle starts to feel stiff, no disassembly needed. Owners love how easily it cranks, even under heavy load, and how the gearing feels tighter and smoother than cheaper replacement jacks.
Simple Bolt-On Install: Fits Standard Trailer Frames
No welding or drilling required—this jack bolts around frames up to 5" tall x 3" wide with the included mounting bracket and 3/8" hardware. The bracket height measures 7-1/4" retracted and 22-5/8" extended, giving plenty of range without hitting toolboxes or winch posts. Whether you’re replacing a worn-out OEM jack or adding support to a work platform or custom trailer, this 2,500-lb-capacity unit goes on cleanly and works right away.
Stable Support You Can Trust: Square Tube Strength and Fixed Mount Design
This jack doesn’t swivel, twist, or ride on a weak pivot pin. It’s a fixed-mount square jack that stays rock solid when you set it down. The flat footplate keeps your load steady, whether you’re supporting a heavy trailer tongue or just leveling for drainage. Once you’ve used a solid square-tube jack like this one, you won’t go back to a wobbly wheel type again.
Specs
Application
- Trailer frame size: up to 5" tall x 3" wide
Weight and Capacity
- Lift capacity: 2,500 lbs
Dimensions
- Bracket height (retracted): 7-1/4"
- Bracket height (extended): 22-5/8"
- Total adjustment: 29-1/8"
- Lift: 15-3/8"
- Drop leg adjustment: 13-3/4"
- Inner tube width: 2"
- Outer tube width: 2-1/4"
- Mounting bracket dimensions: 6-1/2" long x 6-1/2" wide
- Handle radius: 7-7/8"
- Adjustment hole spacing on drop leg: 3-3/8" from center of hole to center of hole
- Between center of hole on bottom and center of nearest hole: 3-1/2"
Warranty
- Warranty: 1-Year warranty
MJSQ-2500B etrailer by Ram Square Trailer Jack w/ Foot - Fixed Mount - Zinc - Side Wind- 15-3/8" Travel - 2,500 lbs
Compare to Fulton FHD2500
Similar to FHD2500 Fulton Fixed Mount Boat Trailer Jack
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Arrived Damaged
- Wrong item was ordered
- Defective
Ratings & Reviews
4.8
1142 reviews
by:
John
06/10/2026
The trailer jack is very nice and perfect. I'm replacing a 25yo jack which bolted through a 2x6in beam, on a 3-axle trailer, and using those original holes and position would not work out, so I attached to a suitable 2x4in crossbeam, as close to center as the OEM design was.
by:
Joseph
09/29/2026
Well I dont know why I waited so long to replace my boat trailer jack. If you have a standard boat jack buy this one to replace it. Just drop the leg down and save 15mins cranking, this is almost one finger operation to raise and lower. Thanks for fast free shipping
by:
Lucas
08/18/2026
Perfect fit! I didn’t want to drill new holes in my aluminum snowmobile trailer. Glad I researched and found this Jack to bolt in place of the old Jack.
by:
David
08/23/2026
Great quality. Exact replacement of old corroded one used in salt for snowmobile trailer
by:
Nathan
11/08/2018
I love it! I bought a used trailer for my 50 million pound pontoon ( OK, maybe 2500 lbs). The jack that came with it failed the fourth time I lifted it, and the tongue weight was so high that a concrete block I was using underneath shattered with the tongue resting on it. I replaced the broken concrete with a block of wood which is much better. The old jack also had a wheel which was utterly useless because of the trailer weight. This new jack installed easily and cranks smoothly and with almost no effort. Also has a grease zirc built in, but did not say how often to grease it. Very nice...........
by:
Art
07/19/2019
Jack is perfect for my boat trailer. It has the proper lift height to drain the deck water from boat compared to original trailer jack. It’s very sturdy and stable for this 25’ trailer. Great product.
Art
7/20/2020
Works well except the crank handle is very rusty and will need some sanding and paint.
by:
Mike
06/21/2021
Completely 100% satisfied with this flat bottom tongue jack. Works like a champ and is much safer than the Jack with the wheel that came on the trailer. Goes straight up and down and does not twist or bend like the original wheel bottom kaxl that came on the trailer.
Mike O.
6/22/2022
After a year Jack still works like new. This is the only one I would buy as I’ve had several in the past with the wheel that were unstable and unsafe. Remember to grease the fitting on the standard at least once a year.
by:
Russell
04/29/2026
Way better than any swivel wheel boat trailer jack. ALL boat trailers should come standard with this. I love it!
by:
Scott
03/25/2026
I ordered a dutton jack round you sent a ram from China and square. I don't like crap from china. I may never buy from you again also jack feels rough when cranking handle. I feel it should be a smoother turn always
by:
Scott
07/31/2026
Matched the jack I had on trailer. Easy install.
by:
Helen
04/08/2019
Delivery as promised! Quality jack! Super easy to install. We had ordered the same jack from Autoplicity and they screwed up our order big time. We should have known better! Old jack with wheel was on bent frame and wouldn't stay straight! Thank u we are very happy!
Helen
4/9/2020
Still great! We absolutley love it. Great quality.
by:
Christine & Craig
05/13/2023
Excellent delivery time!
Very quick and easy installation.
The jack feels well made the cranking is smooth.
Highly recommend this jack.
Very quick and easy installation.
The jack feels well made the cranking is smooth.
Highly recommend this jack.
Christine C.
5/14/2024
After a year of use, the trailer jack is still working like a champ! Replacing a wheeled stand was a good call. The boat is too heavy to roll around and only increases the risk of rolling down the driveway.
by:
Michael
10/14/2024
Bolted right on, height adjustment is much easier than looking for a board or block to put under my old one, cranks easy, and I think this will be the last tongue jack I ever buy for my boat trailer.
Michael
10/15/2025
Still working great
by:
Sam
09/19/2019
My Square Jack / Ram Jack, lasted from April 2013 – about April 2019
I purchased a 2013 inshore Sundance DX22, the trailer came with a 2500 lb Ram Jack, that jack lasted till 2019 that’s around six years. I then came to etrailer.com to purchase a MJSQ-2500B Square Jack which is made by Ram Jack and is the same jack that came with my trailer.
my Ram jack was a 2013 (looked identical) to the etrailer Square jack that I ordered (see pics), the jack lasted till 2019 before the bottom rusted enough so that the shaft on the inside would not extend out or retract inward.
I live in Florida near the salt water, and launch in salt water all year round, so the jack does get salt spray and salt mist on it all the time, and sometimes the bottom of the jack is in the salt water, depending on the tide at the ramps.
Having had boats all my life, six years is a long time for a jack to last in salt water environment. Just to give you an idea of my saltwater environment, my Dodge Ram 3500 bumper and tail pipe rusted out before my jack did (see pics)
Not saying that this is normal or not, just that this was my experience with my Ram jack. Hope my new Ram jack lasts as long.
Pics show it mounted, I decided to spray some zinc galvanized paint on the bottom of the jack, just for a little added protection.,
As far as etrailer goes, from time to time I order parts from them, they never disappoint.
Thanks etrailer for my replacement Ram jack.
I purchased a 2013 inshore Sundance DX22, the trailer came with a 2500 lb Ram Jack, that jack lasted till 2019 that’s around six years. I then came to etrailer.com to purchase a MJSQ-2500B Square Jack which is made by Ram Jack and is the same jack that came with my trailer.
my Ram jack was a 2013 (looked identical) to the etrailer Square jack that I ordered (see pics), the jack lasted till 2019 before the bottom rusted enough so that the shaft on the inside would not extend out or retract inward.
I live in Florida near the salt water, and launch in salt water all year round, so the jack does get salt spray and salt mist on it all the time, and sometimes the bottom of the jack is in the salt water, depending on the tide at the ramps.
Having had boats all my life, six years is a long time for a jack to last in salt water environment. Just to give you an idea of my saltwater environment, my Dodge Ram 3500 bumper and tail pipe rusted out before my jack did (see pics)
Not saying that this is normal or not, just that this was my experience with my Ram jack. Hope my new Ram jack lasts as long.
Pics show it mounted, I decided to spray some zinc galvanized paint on the bottom of the jack, just for a little added protection.,
As far as etrailer goes, from time to time I order parts from them, they never disappoint.
Thanks etrailer for my replacement Ram jack.
by:
Kevin
05/03/2018
Great heavy duty jack, no signs of corrosion after a year of use, still works smoothly and is greaseable. It's used on a heavy triple axle boat trailer that's galvanized so its bolt on construction was convenient.
by:
Greg
09/15/2026
It was great
by:
Patrick
06/08/2019
Great square jack. Easy bolt on, smooth easy crank, adjustable height with the drop leg. Handles the tongue weight effortlessly. Has a grease fitting for lubrication. Fast easy bolt up install.
by:
Patrick
05/24/2023
The tongue jack is constructed very well. It lifts the trailer for my 25 ft boat effortlessly. It is low geared and easy to raise or lower the trailer.
by:
William
02/27/2026
great price and fast shipping
by:
Brian
06/16/2023
So far so good. well crafted, Straight forward putting it on w/ 4 bolts. Importantly kept the boat upright. Shipping was quick and price was perfect. Now comes the test of time. Fingers crossed that with some grease from time to time i will get many yrs out of it.
by:
David
08/13/2026
Excellent!
by:
PO1
05/16/2024
bought this jack for our 29' RB-S trailer and it worked out perfectly. easy swap! Customer service was quick to respond with a quote as well.
Po1
5/22/2025
after a year of use the jack is still working as it should. The only issue is rust accumulation at the foot of the peg, but I think thats more of a local environment issue than the product itself. perfect replacement for our small boat
by:
Scott
04/25/2024
Easy to install. Rugged and easily adjustable. Second trailer I’ve used this jack.
Scott
4/26/2025
Very nice jack. I highly recommended.
by:
Robert
07/18/2023
Great product. Easiest thing I have ever installed on my boat or trailer.
by:
Peter F
03/21/2026
Great but would be better with a couple drain holes in the base to prevent rusting
25
1142
true
Show More Reviews
See what our Experts say about this etrailer Trailer Jack
- Trailer Jack to Avoid Tailgate Clearance IssuesThere are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like # D-26, that would move the trailer back further away from the truck and give you clearance you need. If you know what size the hitch on your vehicle is, the rise or drop of the ball mount for your trailer, if you're using weight distribution or not, and the measurement from the center of the hitch pin hole to the center of the ball hole I can make the best recommendation...
view full answer...
- Trailer Jack Solution for Trailer Tongue that is 6 inch by 3 inchThat is a pretty tall trailer frame but we do have a solution Dan. You could use the part # HD50000101 unless you wanted a swivel option. Then I would go with a weld on style jack like the etrailer # TJD-7000S for a sidewind or the part # TJD-8000 for a top wind. Or if you wanted something that could swivel you'd want a pipe mount like the part # BD178203.
view full answer... - Will a Taller Drop Leg Fit Fulton 2.5K Square Fixed-Mount Marine Jack FHD2500Fulton Square Drop Leg for Stabilizer Jack, 29" Long Item # FSJ20324 by itself will be 24-3/4 inches tall from where it attaches to the jack to the bottom of the foot with the drop leg in the tallest position. It is essentially more than doubling the lift amount of Fulton Square, Fixed-Mount Marine Jack - Drop Leg - Sidewind - 2,500 lbs Item # FHD2500. However, because the drop link is so tall it will not be able to retract all the way into the jack leg it is attached to so keep that in...
view full answer... - Mounting Hole Size for A-Frame Trailer JacksThe mounting hole dimensions of A-frame jacks are a standard 3 inches apart on center, so you will need to weld your new jack on. I highly recommend the etrailer Round, A-Frame Jack # TJA-5000S-B, which has a 5,000 lb capacity and will give you 15" of lift. It has an outer tube diameter of 2-1/4" and sidewind handle; for a footplate you would want # JF-99. This jack has been highly praised by our customers. I've added links to video reviews of this jack for you to take a look at as well.
view full answer...
- Recommended Maine Trailer Jack for a 2006 Mastercraft X-StarI have the perfect replacement trailer jack for your 2006 Mastercraft X-Star boat trailer. For this, I recommend using the Fulton F2 Swing-Up, Wide-Track Trailer Jack part # F1413050334. It has a 1,600 lb. capacity and can raise your boat trailer up to 8". As long as your trailer's tongue does not weigh more than 1,600 lbs. then this jack will work well for you. You will also want to use the Weld-On Mounting Bracket and Hardware for Fulton Swing-Up Trailer Jacks part # F500277 to use...
view full answer...
- Recommended Bolt On Jack for a 3" Thick x 6" Tall Trailer TongueI sure do Zach! The Ark Xtreme Off-Road Swivel Trailer Jack w/ 2 Wheels item # ORJW750BD is going to be the best option for your 3" thick x 6" tall trailer tongue. It's designed for 2" thick trailer tongues, however we've spoken with the manufacturer before and you can use longer M8 high tensile bolts to accommodate the additional thickness. The Ark Xtreme Off-Road Swivel Trailer Jack item # ORJW750BD is a sidewind jack with a 1,650 lbs capacity. It will provide you with 18" of lift and...
view full answer... - Options For Bolt On Trailer Jack On Side Of A Frame Of TrailerHey Jaremy, do you want to send me a picture of your current setup? I'm not familiar with any side mount electric jack, especially one rated for 7,000 lbs. The options we have are manual such as Square Pipe Mount Swivel Trailer Jack w/ Foot - Drop Leg - Sidewind - 15" Lift - 7,000 lbs # TJDP-7000S-B, which is a pipe mount and attaches to the trailer via the included mount. We have the manual jacks that bolt onto the side of the A frame like you were talking about, but they are rated...
view full answer... - Recommended Fenders for a Magic Tilt Trailer w/ Mounting Holes 62" ApartHey Eamon, thanks for the measurements. I recommend the Tandem Axle Teardrop Trailer Fenders for Boat Trailers item # HP54VR. The 60" long ones you referenced are going to be too short to reach your mounting holes so I think it's safe to assume you're correct about those rubbing against your wheels. The Tandem Axle Teardrop Trailer Fenders item # HP54VR measure 65" long and look great on boat trailers. They're designed for 14" wheels and are 9" wide x 15" tall. These are made of 16 gauge...
view full answer... - etrailer Square Jack w/ Footplate to Replace Ram Side Wind JackThanks for the pictures! It looks like you have a Ram side wind jack and we do sell replacement parts for it. The jack you were looking at would be a great replacement for it if these parts do are not what you are looking for. The etrailer Square Jack w/ Footplate item # MJSQ-2500B is a bolt on, drop leg, sidewind jack. It has a 29-1/8" Lift and like your Ram jack is rated for 2,500 lbs. The rust-resistant, clear zinc finish protects against rust and corrosion caused by contact with water,...
view full answer...
- Replacement Boat Trailer Jack Non-Swiveling For Clearance Of HitchMate Boat Trailer StepThe HitchMate Boat Trailer Step part # HE4036 should fit with a swing up jack depending on where you place the step. The retracted height of the Fulton Bolt-Thru Swivel Marine Jack - Bolt On - Sidewind part # FXP15L is 26" so you may be able to make both fit depending on where you want the step to be located on your trailer frame. If you still prefer a jack that does not swivel, I recommend etrailer Square, Fixed-Mount Marine Jack - Drop Leg part # MJSQ-2500B which has a 29-1/8" Lift...
view full answer...
- What is the Difference Between the Fulton HD50000101 and the etrailer MJSQ-2500B?Though these two jacks do look to be nearly identical, there is one fairly large difference, and one lesser of one as well. The large one being the weight capacities they can handle. The # HD50000101 is rated up to 5,000 pounds, whereas the # MJSQ-2500B is rated up to 2,500 pounds. So it is mostly the internals that are different, which is why they look like each other. The smaller difference is how the cranks attach to the jack. The # HD50000101 has a gear box, for the lack of a better...
view full answer... - Brainstorming Sidewind Trailer Jack for 2 Inch Receivers On Cargo Trailer Corners For StabilizationInteresting. We don't have that specifically, but there are a couple of routes you could go. Most trailers will use the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 # TJSC-24 for stability in the corners so you could mount a receiver shank to that and use # TJSC-24-HD as a sidewind crank. It sounds like you were picturing more of a trailer tongue style option, so you could use a jack like the etrailer Square Jack w/ Footplate - Drop Leg - Bolt On - Zinc - Sidewind - 29-1/8"...
view full answer... - Replacement Drop Leg for the etrailer Boat Trailer Jack w/ Footplate MJSQ-2500B Hey Tom. The only replacement part I have for the etrailer Boat Trailer Jack w/ Footplate item # MJSQ-2500B is the drop leg item # TJD-5000-FT. The drop leg that comes with this jack is 1-3/4" square which is the same as item # TJD-5000-FT. It also has the same hole spacing. What replacement parts are you looking for and what problems are you having with your jack? You can add this information, along with any other questions you have, where it says Add Comment.
view full answer... - What is the Hole Spacing for etrailer Square Jack w/Drop Leg - Bolt On - Sidewind - 2.5K MJSQ-2500BThe mounting holes on Square Jack w/ Footplate - Drop Leg - Bolt On - Zinc - Sidewind - 15-3/8" Travel - 2.5K Item # MJSQ-2500B are spaced 1" apart on center for the top 3 holes and bottom 3 holes. The 2 inner-most holes are spaced 1-1/2" apart on center. Side to side the holes are spaced 5-1/2 inches apart on center.
view full answer...
- Recommendation For Replacement Trailer Jack For Four Winns Boat TrailerA solid replacement jack that I recommend is the Square Jack w/Footplate-Bolt On, Item # MJSQ-2500B. This item is a great marine jack that has a rust-resistant zinc finish and that is built to be flexible and durable. It has a lift capacity of 2,500-lbs, fits a frame height from 2 inches to 5 inches, and has a comfortable, grooved grip handle. If this will not work for you, send me some more information like weight capacity needed, mounting bracket dimensions, pictures, etc. and I will...
view full answer... - Recommended Trailer Jack With Shortest Retracted DimensionThe etrailer Square, Fixed-Mount Marine Jack, part # MJSQ-2500B, you referenced is a fixed position jack. The jack leg would protrude below the level of the trailer tongue and would not be the flatter surface you said you are looking for. The closest to 1-1/2 inches you said you need is the Bulldog Rack-and-Gear Jack with Footplate, parts # BD018161 and # BD018520. This is a weld-on system with a 750 lb lift capacity, and measures 2-1/2 inches fully retracted. This jack has a lift distance...
view full answer... - Availability of Caster Wheel for etrailer Square Tube JackWe don't offer a caster wheel for the etrailer # MJSQ-2500B 2500 lb capacity jack you mentioned, mainly because the casters will limit the capacity of the jack because the capacity of the caster wheels typically top out at 1000-1200 lbs. What's the tongue weight of your trailer? If it's below 1000 lbs, you can use a trailer dolly like the Trailer Valet, part # TVXL2 for a 2 inch trailer ball or # TVXL25 for a 2-5/16 inch ball. These trailer dollies are meant for use on a flat surface that's...
view full answer... - Options For A Tongue Jack With Low Retracted Height For An ATV TrailerHello George. I believe I understand what you are describing. I really cannot recommend modifying a jack in the way you described though. If you need something with a retracted height of less than 10-1/2" we do have a few options for you. One is the Square Jack w/ Footplate # MJSQ-2500B. This jack has a 7-1/4" retracted height. As far at the bolt on tongue jacks we offer, this will have the lowest clearance of all of them. The only downside is that this jack has a footplate and not a wheel....
view full answer... - How Much Grease Should Be Added to Square Jack with Footplate MJSQ-2500BThe grease fitting on the Square Jack with Footplate part # MJSQ-2500B is just used for maintenance. I don't have an exact amount of grease to run through the fitting as there are too many variables but if you ever feel the jack getting harder to use you would just squirt a few pumps into the jack. It would also be a good idea to add a bit of grease before each season. The orientation of the jack does not matter when applying grease. I recommend the LubriMatic Mini Grease Gun Kit with...
view full answer... - Can Handle on 2,500 Lb Square Jack - Drop Leg be ReversedThe handle on the Square Jack part # MJSQ-2500B which is our version of the Fulton FHD2500/HD25000101 is not reversible. The jack is designed to be mounted on the outside of the frame so any other orientation would affect function. In regards to capacity, the jack has a 2,500 lb rating but this only corresponds to the tongue weight of the trailer. The tongue weight should only be around 10-15% of the trailer's loaded weight. It would be more than capable of handling a trailer your size.
view full answer... - Recommended 1,500 Lb Non-Swivel Tongue JackYes, we have the etrailer Square Jack w/ Footplate - Drop Leg - Bolt On - Zinc - Sidewind - 29-1/8" Lift - 2.5K # MJSQ-2500B that has a 2,500 lb capacity, and a total lift of 29-1/8", and does not have a swivel feature. The next closest option we have is the Fulton Fixed-Mount Marine Jack part # TJ12220301 which has a 1,200 lb capacity, can extend up to 15", and does not have a swivel feature. These will be the best options that we have to replace the Fulton XLT Bolt-Thru Swivel Trailer...
view full answer... - Recommended Tongue Jack for 12K Sea Ray SundancerI do have some great jack options for you and your boat but the jack does not need to be rated for the entire weight of the boat, at least directly. For example, a trailer jack rated at 2,500 lbs is more than enough for a 12,000 lb boat. The reason for this is that the jack only need to be rated for the tongue weight, which is usually about 10-15% of the loaded boat+ trailer weight. Therefore, if you had a 13,000 lb loaded boat and trailer then all you would need the jack to be rated for...
view full answer... - Recommended Side-Mount Trailer Jack for Camper Trailer to Improve Tailgate ClearanceI understand your tailgate clearance need but I do not recommend going without a tongue jack on your camper trailer. What you might do instead, to both improve your tailgate clearance and retain the safety and utility of a trailer tongue jack, is install a different type of jack, a side-fame-mount type, in place of the A-frame tongue jack. The stabilizer jacks on your camper are designed to support weight but would not take kindly to the bumps they might receive as you back your tow vehicle...
view full answer... - Replacement Trailer jack for Ludo Dump TrailerWe don't have a repair kit for that jack. Since it sounds like the screw is damaged and the handle is already broke it's time for a new jack. The etrailer jack part # MJSQ-2500B would be a great replacement for this.
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Updated by:
Lindsey S
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Mike S
Updated by:
Alex H
Updated by:
Ryan F
Expert Research:
Michael H
Expert Research:
Jameson C
Video Edited:
Jacob T
Video Edited:
Jonathan Y
Video by:
Dustin K
Installed by:
Cole B
Installed by:
Hayden R
Installed by:
Aidan B
Written by:
Amanda M
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Nathan
11/9/2019
Peachy keen. I am a happy dog