Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs

Ask the Experts about this Brophy Trailer Hitch Ball Mount

• Availability of Extra Long Ball Mount with 10,000 Pound Towing Capacity
  I have a ball mount that will meet most of your requirements. We do not have a ball mount exact to the specifications you asked for. The Brophy Heavy Duty Extra Long Ball Mount # BH20 offers up to 10,000 pound gross towing capacity with a 1,000 pound tongue weight. This ball mount fits 2 inch x 2 inch hitch receivers, has a solid shank, and has an overall length of 17 inches. From the center of the hitch pin hole to the center of the ball hole measures 13-1/4 inches. The drop on the...
  view full answer...
• Why Does Ball Mount BH20 Have a Solid Shank While Ball Mount 2923 is Hollow
  When the shank of a ball mount or hitch-mount accessory - say a bike rack for example - is solid rather than hollow this typically means it will be stronger. It also means it will be heavier. The Brophy Ball Mount # BH20 has a solid steel shank which is part of why it has a very substantial 10,000-lb weight rating. The roughly similar Draw-Tite ball mount # 2923 offers a 7500-lb weight rating; this part has a hollow shank. Hollow shanks also allow use of a locking anti-rattle device...
  view full answer...
• Will Using a Longer Ball Mount Put Too Much Stress on the Trailer Hitch on a 2006 Dodge Ram
  The Brophy ball mount # BH20 is not too much longer than standard length ball mounts so the extra stress it would put on the trailer hitch would be minimal if at all. As long as the trailer hitch on your 2006 Dodge Ram has a tongue weight capacity to handle the trailer tongue weight and the 7500 pound gross trailer weight you will be good to go.
  view full answer...
• Recommended Extra-Long Ball Mount For 2015 Land Rover Range Rover Sport
  We have several extended ball mounts that will work for your Range Rover Sport. The ball mounts have various rise or drop features, so you will want to know just how much of a drop or rise you need. You can check out the attached helpful article that explains how to choose a ball mount that works for you. If you do not need a lot of rise or drop, I recommend a ball mount like part # BH20. This ball mount has a 2 inch drop or 3/4 inch rise and is 13-1/4 inches long from the center of...
  view full answer...
• Longer Ball Mount Recommendation With at Least 750 lb Tongue Weight Capacity
  We most likely will have a solution for you, but hitch extenders end up cutting the capacity of a hitch by 50 percent. Your best solution would be to go with a longer ball mount to help give you that distance. For example, the Brophy ball mount part # BH20 measures 13-1/4 inches from the center of the ball hole to the center of the hitch pin hole and it has a 10,000 lb capacity with a 1,000 lb tongue weight capacity. I attached a page that has all of the longer ball mounts we offer...
  view full answer...
• Longer Ball Mount Recommendation to Clear Rear Spare of 2005 Jeep Liberty
  A longer ball mount in a hitch like the Curt part # 13044 which is confirmed as a fit for your 2005 Jeep Liberty would be what you need. It sounds like you already have a hitch though so for a ball mount the # BH20 has a distance of 13-1/4 inches from the hitch pin hole out to the ball mount hole so it would be a great option. This ball mount has a 2 inch drop/3/4 inch rise so if you need a different rise/drop you would want to check out the link I attached to the page that has all of...
  view full answer...
• Longer Ball Mount that Could Clear Out Past Rear of Jeep Wrangler Spare
  We do have longer ball mounts like the Brophy part # BH20 which is 13-1/4 inch long from hitch pin hole to ball hole center. This has a 10,000 lb towing weight capacity and would easily clear the rear spare of your Wrangler as well. For a 2 inch ball then to use with this we have the part # A-90.
  view full answer...
• Recommendation to Add 36" Extension for Towing 7,500 Pound Boat Trailer with 2017 Ford F-250
  The longest hitch extension we have available for the factory 2-1/2" hitch receiver on your 2017 Ford F-250 is the Reese Extension # RP45292, which provides up to a 34" long extension but doesn't feature the necessary towing weight capacity to safely pull your trailer. Any shorter extender that you might be able to pair with a longer ball mount to get close to the total extension needed isn't going to have enough weight capacity, either. This means your only real option to create this...
  view full answer...
• Trailer Hitch Receiver Compatible with 2010 Chevy Silverado 2500HD Service Body
  The B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2" # BWHDRH25187 is the best option for your 2010 Chevy Silverado 2500 chassis with 10 inch step bumper. The only thing to consider is the depth of your bumper is greater than the typical step bumper. I've attached a photo to assist. This will put your trailer hitch receiver under your bumper, so I recommend an extended length ball mount like # 80232 or # BH20. Then you can use a 2 inch ball like # A-90 or 2-5/16...
  view full answer...
• Troubleshooting 2 Inch Ball Mount that Fits Too Tight In Vehicle Receiver
  The Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs # C45036 sounds like it may have a little too much powder coat or something to cause resistance like you stated. Alternatively it could be the receiver side as well but it seems odd that the Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs # BH20 fits if it were the receiver side. The # BH20 will work fine for your 7,500 lb capacity if you don't want to purchase another option. You can...
  view full answer...
• Difference Between Brophy # BM20 and # BH20 Ball Mounts
  The Brophy Ball Mount # BM20 and the Brophy # BH20 referenced in your question are extremely similar to each other. They are both designed for 2 inch trailer hitch receivers, have a 10,000 pound towing weight capacity, feature a long, 13-1/4 inch shank and will give you either a 3/4 inch rise or a 2 inch drop. The primary difference between the two units is the ball hole diameter. The # BH20 has a 1-1/4 inch ball hole diameter, which will be compatible with a hitch ball with this same...
  view full answer...
• Recommendation for 4 inch Hitch Extender to Pull 8,000 Pound Trailer
  We do have a large selection of hitch extenders that will allow for the needed clearance between your tailgate and jack. The shortest extender we have available for 2 inch receivers that has the required capacity for your 8,000 pound trailer is the Roadmaster # RM-071-1075. This extender measures 7-3/4 inches from the center of the hitch pin hole on truck's hitch to the center of the hitch pin hole on the adapter. It has a 10,000 pound towing weight capacity. As you mentioned, using...
  view full answer...
• Hitch Extender for 10,000 lb Travel Trailer Compatibility
  I wish you would have asked this question prior to your purchase of the Curt Extender # C45791, because this extender will not work for your application. It is rated for the 3,500 lb total trailer weight towing capacity and because it is an adapter will also decrease your tongue weight rating of your trailer hitch by 50%. Instead, you may want to consider the Brophy Ball Mount for 2" Hitch # BH20. This ball mount is capable of towing 10,000 lbs and has a measurement of 13-1/4 inches...
  view full answer...
• Hitch Extender that is At Least 3-1/2 Inches Deep From Pin Hole to Inside Receiver Tube
  The Roadmaster Htich Extender # RM-071-1075 measures approximately 3 inches deep from the pin hole to the furthest point inside the receiver tube. It's also only designed to be used to flat tow a vehicle with a hitch style tow bar. It can't be used with a ball mount. The Curt Hitch Extender # C45791 has the same measurement of 3 inches and can be used for towing a trailer; however, it has a much lower weight capacity at 3,500 pounds. Also, when using a hitch extender your hitch's...
  view full answer...
• Availability of Ball Mount with 12-14 Inch Distance Between Hitch Pin Hole and Ball Hole
  I'm assuming you're looking for an extra long ball mount. We have a few to choose from. Curt # D-26, 12-5/8 inches long from center of pin hole to center of ball hole- 7500 lb capacity Curt # C45270, 13 inches long from center of pin hole to center of ball hole- 7500 lb capacity Curt # D-28, 14-1/4 inches long from center of pin hole to center of ball hole- 6000 lb capacity CR Brophy # BH20, 13-1/4 inches long from center of pin hole to center of ball hole- 10,000 lb You'll want...
  view full answer...
• Recommended Trailer Hitch For 2015 Jeep Wrangler
  The hitches you listed, part # 9883544, and part # 13432, are both manufactured by Curt and are Class lll hitches with 2 inch receiver openings. There is no difference in the performance or capacities for these hitches. We received special pricing for the # 9883544, and that is why it is listed as a separate item. My son-in-law recently purchased the # 9883544 for his Jeep Wrangler and is very pleased with its performance. If you plan on using the hitch for towing I recommend a ball...
  view full answer...
• Why Isn't There a 2-5/16" Hitch Ball Available with a 3/4" Diameter Shank
  You are right that there aren't any 2-5/16" hitch balls available that feature a smaller 3/4" diameter shank. This is simply because the higher weight capacity that a 2-5/16" ball provides requires a larger diameter shank to maintain this rating. The most common shank diameter size for this ball is a 1-1/4" like the Draw-Tite # 19286. You also definitely want to make sure you are using a 2-5/16" hitch ball if that is what the coupler on your trailer accepts. Using a smaller 2" ball...
  view full answer...
• Recommended Ball Mount and Trailer Hitch for 2017 Jeep Wrangler
  For a trailer hitch on your 2017 Jeep Wrangler, I recommend the Curt Trailer Hitch Receiver # 9883544. This is a Class III, 2 inch receiver that will provide a gross trailer weight capacity of 3,500 pounds and a tongue weight capacity of 350 pounds. No drilling will be required during installation, however keep in mind that the exhaust will need to be temporarily lowered and if there are any tow hooks present, they will be permanently removed. I have attached an installation video on your...
  view full answer...
• Extra Long Ball Mount to Allow Installation of Towtector Debris Guard on F-350
  It sounds like you are looking for a longer ball mount to use in your hitch to allow installation of the Towtector debris guard. I have linked you to our page for extra long 2-inch 10K ball mounts. For a 2-inch size we offer the Brophy # BH20 which measures 13-1/4-inches from the center of hitch pin hole to the center of the ball hole and either 3/4-inch rise or 2-inch drop. There are longer ball mounts but they do not have the 10K rating you need.
  view full answer...
• Availability of a 12 inch or Longer Ball Mount to Clear Open Tailgate of 2011 GMC Sierra
  I have a solution that'd get you the ball mount length you're needing. First, you'd need to use a reducer, part # 58102 to convert your 2-1/2 inch receiver down to a 2 inch. Then, you'd use a ball mount like the # BH20 from CR Brophy. The # BH20 offers a 2 inch drop (we don't have anything in a 3 inch drop) and a hitch pin hole to ball mounting hole distance of 13-1/4 inches. For a 2 inch ball, you'd use part # A-90. As long as you have the trailer ball within 1 to 1-1/2 inches of level,...
  view full answer...
• Hitch Extender Compatibility with Long Ball Mount for Use With In-Bed Camper
  The Curt Extender for 2" Receivers -18" Long # C45796 can be used with the Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs # 80232 or the Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs # BH20. You may want to consider using hitch locks like # e98882 that can be keyed alike. Using a hitch extender will not reduce your towing capacity, but will reduce your trailer hitch tongue weight rating by 50%.
  view full answer...
• Hitch Extension Between Slide In Truck Camper and Trailer Accounting for Capacity Reductions
  Since you have a F350 I am going to assume that you have a 2-1/2" hitch receiver opening. If you have a different size, just let me know and I will make refined recommendations. To get some additional space (presumably to open the camper door) you could use an "Extender" like the 14 inch Curt # C45795. This fits 2" receivers so you will need a 2-1/2 to 2" reducer like the B&W # BWRHXA2182 if your truck did not come with one. However the use of an Extender" reduced the tongue capacity...
  view full answer...
• Hitch Extender Needed with Gross Weight Rating of at least 5,000 lbs for a 2" Hitch Receiver
  If you are looking for a 2" receiver to 2" receiver extender rated for at least 5,000 lbs we have the Roadmaster Anti-Rattle Hitch Extender # RM-071-1075. This has a 7-3/4" extension with a 10,000 lb gross trailer weight rating and a 400 lb tongue weight rating. Keep in mind that using an extender like this will reduce the tongue weight of your trailer hitch by 50%. Because of this I recommend looking into using a ball mount that has an extended shank like the Brophy Ball Mount # BH20...
  view full answer...
• Recommended Trailer Hitch And Long Ball Mount For 1994 Chevrolet C2500 Pickup With drop Bumper
  Since you have a drop bumper on your 1994 Chevrolet C2500, I recommend the Curt Trailer Hitch, part # C15317. This is designed to work with the bumper you have on your truck. I also recommend the Brophy Heavy Duty Extra Long Ballmount, part # BH20. This ball mount works with a 2-inch receiver opening and measures 13-1/4 inches from the center of the hitch pin hole to the center of the hitch ball hole.
  view full answer...
• Availability of High Capacity Extra Long Ball Mount Compatible With 2-5/16 Inch Trailer Ball
  The CR Brophy Heavy Duty Extra Long Ball Mount, part # BH20 has a 13-1/4 inch distance between the hitch pin hole and the hole where the ball installs. The ball mount has a 10,000 lb capacity, has a 2 inch drop/3/4 inch rise and is compatible with a 2-5/16 inch trailer ball like part # 19286 which has a 12K capacity. Remember, you'll be limited to the capacity of the lowest rated component.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?