Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This 3-7/8" x 1-1/4" rectangular LED fender light does double duty with amber LEDs facing forward and red LEDs facing back, giving you clear markers from both directions. It’s P2-rated for a 90-degree beam pattern, so each side stays bright and defined without spillover. With two diodes drawing only 0.08 amps at 12V, it’s efficient and dependable for all-day or nighttime towing.
Forget about chasing down replacements for flaky incandescent lights. This sealed LED setup lasts up to 50 times longer, using less power while delivering more consistent brightness. There are no fragile filaments or bulbs to replace—just a solid, reliable light that keeps working trip after trip.
The housing is built from polycarbonate with an acrylic lens that stands up to vibration and road grime. Hard-wired terminals are potted in polyurethane to keep connections protected from moisture and corrosion. This isn’t a throwaway light—it’s made to hold steady through harsh use without flickering or shorting out.
Mounting is straightforward thanks to its surface-mount design. It installs using a bracket (sold separately) and accepts a standard 2-prong plug for easy wiring to 12V DC systems. The compact 7/8" depth keeps it tucked in close to the trailer’s side or top fender edge for a clean, low-profile fit that looks like it belongs there.
This P2-rated clearance light meets DOT lighting regulations for use as both front (amber) and rear (red) clearance lighting. Whether you’re towing at night or parked roadside, it keeps your trailer visible from the right angles so other drivers can clearly see your position and movement.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ellen: Hey everyone. I'm Ellen here at etrailer.com and we're going to be taking a look at the LED Trailer End Marker Light. This is going to be for your fender to show both the end of your trailer with the red light and also a side marker light. So it kind of does two in one with the two different colors. It has two little prongs to the back that are going to be our positive and negative connections. So it makes it pretty easy to wire this up.
The thing that I like about it is that it is an LED light. Typically they're going to last a lot longer, have a very lessen power draw than your typical incandescent, and there's no bulbs to replace, ever. So pretty much maintenance-free. As long as the housing doesn't get damaged should never have to do anything with this light. It should last a really long time.This does have, again, that dual face will have red on one side, amber on the other.
Again, we'll have our two little prongs at the back to mount that up. A wiring option that you can get as a base that looks something like this. This one is part number A65PB, you can find that here at etrailer.com. There are a couple others that are also listed on the product page here. And basically these two prongs fit into the two holes there and then it mounts up to this.
So it provides a base, has one wire for this particular one coming off. This is going to be our power wire, and then it's grounded through the mounting holes. So you put your hardware through here and that'll ground it to the frame. Doesn't come with any hardware, but that is how it works. So I'm going to plug this in and you can also notice there's two little notches on either side that are going to snap in place with this style base.It's easier to just kind of do one at a time, sort of get your little prongs started there, and then it snaps in and voila.
And then we can connect our wires. So again, ground goes to the inside of the mounting hole, that little metal ring in there. And I put my little alligator clamp on one side, and then this little bullet style connector is our power connection. So once I have those two in place, lights on. You can see both sides they're illuminated, turning our light off in the studio. You can get a better idea of how bright it is. This is a P2 rated light so it's going to be for your side marker light. It can only be seen from a 90 degree angle, so you can really just be seen about like there. And then once we get flat, you can't really tell what's going on with that light any more. So that's why it gets that P2, it is DOT compliant.See it's pretty bright for just being those little lights there. My wire came off because I was trying to mess with it, but still pretty bright light for being such a little guy. So now let's talk about measurements. Disconnect my wires, set those aside and we can take this off the base so we can look at how big it is. The base does add a little bit of length, obviously for this one, it's about four inches long. That's pretty typical for these lights and the bases that go with them. To remove it, helps to have a little screwdriver to kind of pry out on the one side. So you can pop that out. Same thing over here, pry out on that and since those prongs are in there as well, also need to remove those. So the light itself without the base in place is about three and seven eighths inches long, just shy of four inches. The width is about an inch and a quarter. Height about seven eighths of an inch without including those prongs.We have two diodes. It is covered by a limited lifetime warranty and it is DOT compliant. Should be a pretty easy to use little light and that's about all there is to it. It does work with 12 volt DC systems so that's going to be pretty much standard for any trailer out there. All in all, I think it's going to be a nice little addition to your trailer to have that lighting function that you need. Hope this video has been helpful in deciding if this is the right light for you. If not, we do have other options available here at etrailer.com. So check them out if you're interested. Thanks for watching.
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
Ratings & Reviews
As advertised and received quickly as always with any orders from E-trailer.
quick shipping and just what i ordered
fast service and the light was just what I needed .
Fast shipping
Needed this to repair my trailer. Did the trick quickly and easily.
Looks better than the original light that came with the trailer. Easy swap. No issues installing.
Plugged into existing mounts. Much brighter and updates look. Very happy with these components.
I could not find this item anywhere for years until my wife came across it from etrailer.com. Thanks!
Beyond impressive experience factory replacement lights for my snowmobile trailer
Perfection
Website was very helpful in finding the base A65PB to match this side marker replacement light. Good price to top it off.
Excellent products and really excellent customer service!
ON TIME, SMALLPACKAGE
Just what I needed...Thank you Very Muc h!
Arrived in a timely manner, well-packed, proper fit and working well. Thank you
ETrailer has almost everything I’ve ever looked for in replacement parts for my trailers. Fast shipping too
Worked perfectly came as described
prompt delivery, easy purchase, accurate product.
Perfect fit
Appears to be an exact fit.
Went on easily and works great
Thank you for the day early on parts, customer will be very happy..
Nice video on how to install and description of product. Easy ordering.
Terri
10/6/2025
It is still working!
This worked Great!!! Exactly what I nee ded
Great light. Plug and play!!
Terry
3/13/2026
It’s been a year and lights are still going strong
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Pam
7/20/2024
Working perfectly!