Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replaces the SpeedKnob and anti-rattle wedge assembly on your Yakima FullSwing, FullTilt, RidgeBack, or SwingDaddy bike rack. Includes the SKS control key needed to change the SKS lock core (sold separately).
Features:
Fits:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to be taking a look at the replacement speed knob and wedge assembly for the Yakima bike racks, part number 8880508. The Yakima replacement speed knob is to be used with the Full Swing, Swing Daddy, Ridgeback and Full Tilt bike racks when their speed knobs are either damaged or the threads at the end are stripped out. It comes with the black knockout here which you're going to remove that and it has the control key to remove the lock core from your previous speed knob to replace it into this one. To get started we'll first remove our wedge piece here by unscrewing it and set it aside now we'll grab our damaged speed knob and start replacing it as well. Now we'll move on to our bike rack and have our Yakima Ridgeback here on our table and the issue with is the thread is stripped out in our wedge. We'll push that off to the side, remove our speed knob as well, now we'll get our new one and start installing it. First since this is a Ridgeback, we'll have to remove this top piece from the wedge. Take our allen tool, unscrew those two allen screws, move onto the one on the inside.
Now we can grab our new wedge and install this piece on top of it. What this piece actually does is it takes up the additional space on our Ridgeback so it'll fit properly in a two inch hitch. If you we're to convert this into an inch and a quarter you would remove this piece again. Finally, our second screw, one last turn to make sure it's nice and tight. Next we'll move onto our lock core switch out here. To remove this plastic cap, we'll take a small flat bladed screwdriver and just pop that out, very easy, and then we'll take our master key here put it into the core and it pulls out like so. Again, very easy.
To place it into our new lock, we'll push it in holding onto the end of the core and pull it out. Now we're ready to install this. We'll take our lock washer and install it on our replacement speed knob here and we'll install it at the end of the shank like so. Then we'll take our wedge and we'll just start to screw it in on the inside. You see the cutout here, you want to make sure that the wedge fits along that area. Here's the end of our speed knob so we'll just match them up, just start threading it in so it catches.
Now we can place it into our vehicle, slide it into our trailer hitch and go by the normal installation procedures for this bike rack. Now we'll go into the end here and tighten down our new knob. As we tighten it down, you'll notice that the shake and play has gone away which means it's working properly. All right, it looks like we're ready to go, we'll lock it into place so it's secure in the vehicle and now we can load up some bikes. There you have it for the replacement speed knob and wedge assembly part number 8880508.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
Ratings & Reviews
Jim T.
3/11/2018
Great—I just put the bike rack on the car getting ready for the spring and all is fine.
Brooke M.
12/11/2024
I really appreciate all the information you gave - thats what makes a review helpful for other folks! Thanks for taking the time to do so :)
Tony
6/27/2022
Great
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mike L.
4/26/2026
It seems odd to me as well. The SKS lock cores are available separately as # Y07202