Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide

See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Recommended Trailer Hitch For A Foreign Model 2020 Ford Ranger FX4
  Hi Drew, The Curt # C97JR you were looking at is designed to fit select model Jeep Grand Cherokee L's and would not be a fit for your 2020 Ford Ranger. All of the custom-fit hitches we currently offer are designed for US models so you'd have to go with an adjustable-fit weld-on trailer hitch instead. These will come with a drop so you'll want to measure from the frame down to make sure the receiver tube will clear the bumper. Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3"...
  view full answer...
• 2006 E-450 Super Duty Shuttle Bus Trailer Hitch Receiver
  For your 2006 Ford F-450 Shuttle Bus you are going to need to use a universal hitch. For this you will need to measure how wide your frame rails are apart on the rear of your bus. Then you will need to know how much drop from the frame rails to the bottom of the bumper is required for the hitch to fit. The Curt Class 5 Universal Weld-on Hitch # C47CR will fit frames that are 18"-44" wide and brackets have a 9" drop. The Curt Class 5 Universal Weld-on Hitch # C99CR will also fit frame...
  view full answer...
• Best Way To Use A Hitch Bike Rack On A Trailer
  I suggest getting a 2 inch hitch receiver for your trailer. A universal one like this # C47CR will work well. You just need to weld it into place. I don't recommend putting the Swagman Original # S64400 in anything other than a hitch receiver. Luckily the Swagman Original is rated to be put on any vehicle you may have with a class III hitch or higher so you're good to use it on the back of your 14 foot trailer!
  view full answer...
• Will The Draw-Tite Trailer Frame Hitch Receiver Fit A 1974 Chevy K5 Blazer With A Gas Tank Shield
  The Draw-Tite Max-Frame Trailer Hitch Receiver 75129 should fit with any OEM parts but just to be used I went out to the warehouse and measured the hitch. From the back of the crossmember tube to the center of the first bolt hole is 1". The distance between the inside of both mounting ears is 30-1/4". This hitch should sit directly under your frame rails so you can use that 1" measurement to see if the tube will run into interference with your gas tank shield. If this doesn't work then...
  view full answer...
  
• Trailer Hitch Option For Shuttle 2011 Chevy Express Shuttle Bus
  For a shuttle bus like your 2011 Chevy Express, you'll need a universal hitch that will be welded onto your frame. You will want to measure your frame though, as it will need to be no longer than 44 inches from outside to outside. So long as you have that, you can use one of the following, depending on how tall you need the brackets to be: - 3" Drop: Curt Class 5 Universal Weld-on Hitch # 15901 - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C47CR
  view full answer...
• Trailer Hitch Receiver and Wiring Harness Recommendation For a 1969 GMC P15 Van
  The Curt Trailer Hitch Receiver # C13900 looks to be the closest bolt on receiver that I can find to fit your 1969 GMC P15 van. It has a 6-7/8" drop from the frame to top of the receiver so that may require you to notch into your bumper slightly. I recommend the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. With this you will be able to place the receiver tube exactly where you want on the rear bumper. This will allow you the best ground clearance without having to modify...
  view full answer...
• Do You Carry a Bike Rack that Will Fit a Heavy Fat-Tire Electric Bike on a Motorhome or Fifth-Wheel?
  Yes! For an electric bike carrier that will accommodate fat bike tires and the torque on the rear of a motorhome and fifth-wheel trailer, I recommend the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount # HLY64FR. The RV Rider has an 80-pound per bike weight capacity and can hold fat tires up to 5 inches wide. In addition, the RV Rider is constructed with bolstered steel that is manufactured to withstand the extra torque. If you need a hitch receiver...
  view full answer...
• Trailer Hitch Option For 1975 Dodge Van
  There are no custom fits for a trailer hitch on your 1975 Dodge van, but you may be able to use a universal weld-on hitch. So long as your frame measures no more than 44 inches wide from outside to outside you can use the Curt Class 5 Universal Weld-on Hitch # C47CR.
  view full answer...
• Solution for Spare Tire Carrier on 1977 GMC Motorhome
  The # TR-2 fits 4" square and 4-1/4" square bumpers. This and other carriers like it will not fit your 1977 GMC Motorhome, but I do have some other options. The first is to mount the Buyers Products Truck Spare Tire Carrier for 19-1/2" Rims or Smaller # 3375201010 on the back. This can either be bolted on (drilling will be required) or welded on. The other option is to use a hitch mounted spare tire carrier like the # e98ZR. Of course this will require you to have a trailer hitch receiver...
  view full answer...
• Solution for Class V Hitch on 2011 Fleetwood Expedition Motorhome
  For hitch fabrication we only offer the receiver tube like the # E-11 or # C49511. You would need to take this to a local fabricator and they would be able to fashion a hitch and brackets that will fit your 2011 Fleetwood Expedition Motorhome. The other option would be to use one of the universal Class V hitches we have listed for your motorhome. We have the Curt # C47CR with a 9" drop and the Curt # C99CR with an 18" drop. Both options have a 2" receiver. The # C37CR and # C87CR are...
  view full answer...
• Solution for Front Mount Hitch on 2007 Dodge Sprinter 2500
  I do have a solution, but there are no custom fit options available for your 2007 Dodge Sprinter 2500. What you can use is a universal hitch like the Curt # C47CR. This is a Class V weld-on hitch so we recommend taking it to a certified welder for installation. The hitch has a 2" receiver, a 9" drop, and fits vehicle frames 18-44" wide. If you need taller brackets the # C99CR is also available with an 18" drop.
  view full answer...
• Receiver Hitch for 2007 Newmar Class A Motorhome on Spartan Chassis
  While we do not have a custom fit option for a 2007 Spartan Chassis we do have several options of universal fit. Please note the attached link to the filtered options and let me know what follow-on questions you have. You will need to make measurements to identify which available option fits best, measure from inside the frame beam to the inside of the other frame beam to get the frame width. If you have, for example, a width of 18-44" then I recommend the Curt Class 5 Universal Weld-on...
  view full answer...
• Removable Winch For 2007 Chevrolet Suburban Overlander
  The only option you have for the front of your 2007 Suburban is like this Curt front hitch # C31012. Since you have a custom built front bumper, you may want to get something like this universal weld on hitch # C47CR. This will have 16,000 GTW so it should be plenty strong. If you can make that work, you will be able to get the set up you're wanting. You could then get this Bulldog Winch Receiver Mount Kit # BDW20155 with this 12K Winch # BDW10043. We have a bunch of weld on hitches,...
  view full answer...
• Hitch Option For 1996 Pace Arrow Motorhome
  There isn't a bolt-on option that will work so you'll have to use a weld-on hitch for your 1996 Pace Arrow motorhome. One that will fit the frame distance of your motorhome and has a 2" receiver (but is actually a Class V hitch), is from Curt, the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. This is for frames from a minimum of 18" to a maximum of 44" which is exactly the range your frame falls in.
  view full answer...
• Parts Needed to Tow 1999 Jeep Cherokee With School Bus
  We do have some hitch solutions for you, but they'll need to be welded in place in order to install them, as none of the universal fit hitches we offer can be bolted on. What you'll need to go with is a universal-fit hitch designed for a service body truck, and in order to choose the correct one, you'll need to measure the needed drop, which is the vertical distance between the underside of the frame member and the lowest point of the rear bumper. You'd then choose the hitch with a drop...
  view full answer...
• Hitch Option For 2011 Chevy Express Cutaway Van
  There are no custom fits for a trailer hitch on your 2011 Chevrolet Express cutaway van, but you may be able to use a universal weld-on hitch. So long as your frame measures no more than 44 inches wide from outside to outside you can use the Curt Class 5 Universal Weld-on Hitch # C47CR.
  view full answer...
• Trailer Hitch Option For 2006 Itasca Suncruiser
  We have a hitch option for your 2006 Itasca Suncruiser, but the # C15400 is 32.94" wide overall and the bolt holes are 30.31" apart from each other. So what you will need is a universal weld-on hitch, which will fit so long as the frame on your motorhome measures no more than 44" outside to outside: - Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide # C47CR
  view full answer...
• Front Mounted Trailer Hitch Options For A 2004 Lexus GX 470
  Hey Eric, There aren't any custom-fit front mounted trailer hitches available for a 2004 Lexus GX 470 so you would need to go with an adjustable-fit weld-on trailer hitch. To do this you'll need to measure down from the frame to the location where you'd like the receiver tube to sit to figure out your drop. I've listed out the drops we currently offer below: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18"...
  view full answer...
• Trailer Hitch Receiver Option For 2007 Ford Collins E450
  There isn't a custom fit hitch for your 2007 Ford Collins E450, so you'll need a weld-on hitch, with the right one depending on the drop you need, as well as your frame width. If the width of your frame is 44 inches or less (from outside to outside), you can use one of the following: - 3" Drop: Class V Universal Weld-on Receiver Hitch and Brackets # 15901 - 9" Drop: Class V Universal Weld-on Receiver Hitch and Brackets # C47CR For the drop, what you'll want to do is measure straight...
  view full answer...
• Trailer Hitch With Drop for Ford Chassis With 34 Inch Frame
  We have an option for you, though the hitch you mentioned will not fit your ambulance on a 1996 Ford F-350 cab and chassis. Instead, you need a universal weld-on hitch, and we have the exact one that will work: - Curt Class 5 Universal Weld-on Hitch with Brackets # C47CR This hitch is designed to fit frames between 18 inches and 44 inches, and gives a 9 inch drop from the frame of the vehicle so it will work great for you since you mentioned needing an 8 inch drop.
  view full answer...
  
• Trailer Hitch For RV on CHevy Express Chassis
  For the hitch, you'll need to go with a universal weld-on option, and since the frame is 42 inches apart, and you need a drop of at least 4 inches, the best option is the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C47CR. The # C47CR will give you a drop of about 9 inches from the frame (which is the closest available to needing at least 4 inches), and is for frame widths up to 44 inches wide. You mentioned Class 4 but I assume you're good with a Class 5 for that added bit of strength. Then...
  view full answer...
• Trailer Hitch Receiver Options For A 2005 Ford E-350 School Bus
  Hi Jacob, The Curt Trailer Hitch Receiver # 14053 lists that it's a fit for cutaway chassis if the bolt holes are 38-5/8 inches from frame to frame. This would mean that the holes in your frame have to be spaced 38-5/8" from center to center in order for the hitch to work. With your vehicle be a school bus and the dimensions that you stated you'll likely have to go with a weld-on adjustable fit trailer hitch receiver. You'll want to measure the distance down from the frame to clear...
  view full answer...
• Recommended Trailer Hitch for a Thomas Saf-T-Liner School Bus
  The best option to add a hitch to your 2006 Thomas Saf-T-Liner School Bus is going to be the Curt Class 5 Universal Weld-on Hitch w/ Brackets item # C97CR. This is a universal hitch that fits frames from 18" to 62" wide. This is our highest rated universal hitch and it has a 20,000 lbs towing capacity. The included brackets will drop of 9" from your bus's frame. There are no custom fit hitches for your Thomas Sf-T-Liner and this is going to need to be welded to your frame for the capacity...
  view full answer...
• Is There A Trailer Hitch Receiver Available For 2012 Ford E450 Van / Bus?
  I have a solution for you, but there are not any custom-fit trailer hitch receivers for your 2012 Ford E450 van / bus so you will want to go with a universal option. The Class V Universal Weld-on Receiver Hitch and Brackets is what I recommend for your E450. You will want to measure and verify how much drop you want; for 3" drop go with # 15901 or for 9" drop go with # C47CR. I attached a demonstration video for you.
  view full answer...

Do you have a question about this Heavy Duty Receiver Hitch?