Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand -…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the…
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit GMC Van AccessoriesSelect A Category Below
Towing
GMC Van Trailer Hitch
GMC Van Trailer Wiring
GMC Van Brake Controller
GMC Van Towing Mirrors
Cargo Control
GMC Van Roof Rack
GMC Van Ladder Rack
Performance Accessories
GMC Van Air Filter
GMC Van Suspension Enhancement
GMC Van Transmission Cooler
GMC Van Performance Chip Tuners
GMC Van Vehicle Lights
GMC Van Tire Chains
GMC Van Fluid Filters
GMC Van Vehicle Sway Bars
GMC Van Catalytic Converters
GMC Van Salt Spreader
GMC Van Vehicle Engine Heaters
GMC Van Off Road Lights
GMC Van Radiator Fan
Vehicle Trim
GMC Van Nerf Bars - Running Boards
GMC Van Vehicle Covers
GMC Van Mud Flaps
GMC Van Replacement Mirrors
GMC Van Windshield Wiper Blades
GMC Van Windshield Covers
GMC Van Vehicle Air Mattress