10k Dexter Replacement Hub for a 8-415

Question

Question:

I have a 2011 trailer dually dexter axles 10k gd. I need a new hub my part number is 8-415 this looks to be obsolete what is the replacement part I will need

asked by: Jeremy D

0

Expert Reply:

I did some checking and the hub/drum we offer that will work for you is the part # 8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS setup. The part number for the ABS version is part # 8-430-7 which we do not carry at this time.

expert reply by: Jameson C

0

Answer 1

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 2

I was able to cross reference the Dexter Hub/Drum 8-415 to the Dexter Trailer Hub Drum Assembly part #8-430-5UC3 which should be an exact replacement. I don't have any depth measurements of the above/drum but what you would need to measure to…

view full answer...

Answer 3

I might have an option for you but we don't offer any flush door latches with an extended striker. However, the Full Size Locking Steel Flush Door Latch part #L3980 matches your door cutout at 4-5/8" long x 3-3/8" so this is our best…

view full answer...

Answer 4

To install a brake controller on your 2017 Ford F750 you will need to hardwire it as there are no factory plugs under the dash. There will be some wires located under your dash that are located on the driver side. You will simply need to use a…

view full answer...

Answer 5

Having a 1.25 spindle, it can be a few bearings that will fit. However, there will not be a hub that uses both an inner and outer bearing of this size. With that said, I highly recommend replacing your axles with something that will use a more common…

view full answer...

Answer 6

If you replace the current brakes on your trailer with the same uni-servo drum brakes and no lockout actuator (like #T2351000), the brakes will deliver 20 percent braking when traveling in reverse. However, the more pressure you apply going backwards…

view full answer...

Answer 7

The Peterson Replacement Lens, part #55-15R, would be the correct lens you are looking for. The lens measures 2 inches by 2-3/4 inches. The distance between the mounting holes is 2-5/16 inches. The mounting screws are included. I have attached a…

view full answer...

Answer 8

According to the specifications of the Electric A-Frame Tongue Jack, #LC285318, from Lippert, the jack motor can draw a maximum of 30 amps at 12 volts. The closer to the capacity of the jack (3,500 pounds) the more power it will draw. I have included…

view full answer...

Answer 9

The Lippert Electric Trailer Jack with Footplate #LC285318 operates on a 12v system and pulls 30amps. So you just need a 12v battery that can handle the 30amp hour draw. Typically the battery found in a trailer would just be a typical car battery.…

view full answer...

Answer 10

The 2019 Honda Ridgeline is pre-wired to attach a 7-Way plug that powers trailer brakes but not all Honda Ridgelines have the wiring harness for a plug and play brake controller adapter. If you need a 7-way I recommend to use Tekonsha T-Connector…

view full answer...

Answer 11

The part number 8-245 is an obsolete part number but I was able to find some info on it. It was basically a 3,500 lb hub and drum that fit a 84 spindle. Because of that we have a solution that will fit. The part #AKHD-545-35-K is a 3,500 lb hub/drum…

view full answer...

Answer 12

Based on my research your Dexter 8-245 hub is a 3,500 lb hub that and the correct replacement inner bearing is part #L68149 with the matching race being part #L68111. The correct replacement outer bearing is part #L44649 and the matching race is part…

view full answer...

10k Dexter Replacement Hub for a 8-415

Product Page this Question was Asked From

Continue Researching