Picking Out Landing Gear Replacement for Legs that Have 19.5 inches Between Weld Stops
Published 06/13/2024
Products Featured in This Question
Question:
I have a 19.5" weld stop.. Do you know what jacks I need to replace? 19.5'' center to center. or top to top..
asked by: jake t
0
Expert Reply:
Hey Jake, the closest landing gear setup we have to the weld stop dimensions you mentioned would be the Ultra Fab kit part # UF17-943010 which has a distance of 19-1/8 inches from center to center. So either way you'll have to move your current weld stops so you could go with the Ultra Fab or the Lippert # LG-183708.
If you are looking for a replacement leg though we don't have anything that matches.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Ultra-Fab Deluxe Electric Landing Gear Set - Weld On - 38" Lift - 12,000 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 10001 lbs or More
- Electric Jack
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: landing gear motor
- Search Results: awning
- Search Results: landing gear
- Search Results: dual motor landing gear
- Search Results: awning fabric
- Search Results: bd500162
- Search Results: 12 volt battery
- Shop: Stromberg Carlson Dual Power Conversion Kit for RV Landing Gear w/ 29-1/2" Legs - 5,500 lbs
- Shop: Mach-C Everest Variable Speed RV Air Conditioner - 18K Btu - Ducted/Non-Ducted - R32 - AC Unit Only
- Shop: Mach-C Everest Variable Speed RV Air Conditioner System - 18K Btu - Ducted/Non-Ducted - R32 - White
- Shop: Replacement Fabric for etrailer Powered RV Awning - 10' Wide - 4-Layer Vinyl - Black Fade
- Shop: Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear
- Shop: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Q&A: Where do the Brackets Install in Relation to the Weld Stops on the Reese Landing Gear # RP500708
- Q&A: What is the Distance Between Weld Stops on Stromberg-Carlson Landing Gear Set LG-1
- Video: All You Need to Know About the Landing Gear Set
- Video: Let’s Check Out the Stromberg Carlson Dual Power Conversion Kit for RV Landing Gear
- Q&A: Replacement AC System for a Dometic Penguin II w/ Heat Pump 651916H751C0-M
- Q&A: Replacement Landing Gear Motor for a 8532-07 Motor
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
Explore Expert Info
![Our Expert]()
on Camper Jacks
on Camper Jacks
Jake T.
6/13/2024
LC712690 this 1 looks to be correct and is the right dimensions with weld stops. is this available to buy just the legs?