bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Camper Jacks


  • Options for Stabilizing Fifth Wheel Automatic Leveling Jacks
  • The JT's Strong Arm Stabilizer Kit # LC191023 paired with the either # LC314597 to adapt it to electric jacks, or # LC314592 to adapt it to hydraulic jacks, can be used with auto leveling jacks without issue. I spoke to MORryde and the # MR72AR said that this should not be used with hydraulic auto leveling jacks, unfortunately. That being said, they did say this will work with most electric auto leveling systems that use square jacks.. It should be noted, however, that the # LC191023...
    view full answer...

  • Mounting Plate Height of Replacement I-Beam Jack Bracket for Lippert Ground Control
  • The overall height of the mounting plate of the Replacement I-Beam Jack Bracket for Lippert Ground Control # LC349975 is 13 inches.
    view full answer...

  • Can Electric Trailer Jack Lift Trailer With Weight Distribution System
  • It is possible that the Electric Jack w/ Footplate - A-Frame - 25-1/2" Lift - 3.5K - Black # e69ZR will have enough power to raise the trailer enough with the weight distribution hitch installed, but unfortunately there is no formula to make sure. If your trailer is relatively light it should have no problems, but if you are in the 800-1000lb tongue weight range a higher rated trailer jack would be a better idea. I recommend taking a look at the Stromberg Carlson Electric Trailer...
    view full answer...

  • Replacement Black Cover for RAM/etrailer Electric A-Frame Jack
  • If you can reply to this email with the pictures I can help you out. Just be sure to let me know what the product is they are installed on!
    view full answer...

  • Replacement Landing Gear Recommendation for a 2011 Keystone Raptor 3812 Toy Hauler
  • While I don't know exactly what landing gear you have on your 2011 Keystone Raptor 3812 Toy Hauler, I can say that you should be able to replace them with the Landing Gear Set w/ Handle # RVLG-8HDL as this landing gear uses the standard weld mount locations of 15-1/2" inside and 17-1/2" outside measurements (see attached). You can confirm fitment by measuring where the weld stops are on your current landing gear. This set comes with a handle but if you don't already have an electric...
    view full answer...

  • Can Electric Trailer Jack Be Powered without Trailer Battery
  • There's a power circuit on 7-way trailer wiring that you could use to power electric trailer jacks like part # SC63VR. While we don't have a diagram that shows this exact connection its really just a matter of running 10 gauge wire like part # 10-1-1 from the power wire of the jack to the pin of the 7-way in the 1:00 position and you'd have the needed power for the jack.
    view full answer...

  • Looking for Replacement Stabilizer Scissor Jack for RPod 179
  • The stabilizer jacks aren't trailer specific, but the mounting hole spacing is pretty standard across the board. I'd recommend removing the damaged jack and comparing the mounting plate hole spacing to what's shown in the provided photos. The # TJSC-24 or the # UF48-979006 are likely fits as the hole spacing is pretty similar between the two. The # UF48-979006 has a 6500 lb capacity and a 24 inch lift while the # TJSC-24 has a 2500 lb capacity and a 18-3/4 inch maximum lift. I've linked...
    view full answer...

  • Can Bent Leg On Lippert High-Speed Power Stabilizer Jack Be Replaced
  • In regards to the Lippert High-Speed Power Stabilizer Jack part # LC369774, you can replace the support arms with part # LC1134122 and the foot assembly with part # LC157584. The legs themselves are not repairable, if either are bent then the entire unit would need to be replaced.
    view full answer...

  • Camper Jacks for Storing Camper on Driveway
  • There are camper jacks that will allow you to take your camper off your truck bed easily, but there is nothing with wheels as that would not be stable enough so they do need to remain stationary. To choose the right camper jacks, you need to know the weight capacity you need, and can choose from either manual or electric jacks. The best jacks are the HappiJac because they permanently install, have the highest weight capacities, and you even have the option of electric jacks for the...
    view full answer...

  • How to Manually Operate the Ultra-Fab Deluxe Electric Landing Gear Set
  • Good question; if for some reason there is an issue with the power or motor, you can manually operate the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010. I took a look at the instructions, and the accompanying cut out from them explains what you'll need to do. There are four screws that hold the motor and gear assembly on, and you'll need to remove those and turn the slotted shaft with a flathead screwdriver. Then, if ever need be you can get a replacement motor with the...
    view full answer...

  • Product Comparison Of MORryder Scissor Jack Cross Brace And JTs Strong Arm Jack Stabilizer Kit
  • The difference between the MORryde Scissor Jack Cross Brace Stabilizer for Trailers and RVs # MR82AR, and the JT's Strong Arm Jack Stabilizer Kit # LC191023 is while both limit side to side movement of your 30' travel trailer, only the JT will limit the front to back due it using 4 stabilizing arms on the front stabilizers. Neither the MORryde or the JT's will need to be removed from the trailer when you are ready to get back on the road. I recommend the JT's Stabilizer Kit, but to determine...
    view full answer...

  • Replacement Manual Jack Handle for RAM Electric A-Frame Jack
  • The correct replacement manual crank handle for the RAM Electric 3,500 Lb Jack part # EJ-3520-BBX is the Replacement Manual Jack Handle for RAM Electric A-Frame Jacks part # EJ-3520-HD.
    view full answer...

  • What Is The Difference Between Brophy Cable Camper Jacks CJ31 and CJ41?
  • I would be happy to help! The only difference between the Brophy Cable Camper Jacks # CJ31 and # CJ41 is the weight capacity. The # CJ31 has a 1000lb weight capacity where the # CJ41 has a 3000lb capacity. Both have the same 17" - 57" lift range, so you will just need to pick the one rated high enough for the weight of your truck bed camper/cargo box. I included videos of the products mentioned for you to take a look at.
    view full answer...

  • Replacement Landing Gear for 2004 Dutchman Sport 30 Travel Trailer
  • Landing gear is designed to stabilize a portion of your trailer's weight, not to support the full GVWR of your trailer. From what I found online, your 2004 Dutchman Sport 30 has a GVWR of 9,764 lbs, so a set of 8,000 lb landing gear (combined) would be more than enough to support the front of your 5th wheel trailer. The Bulldog Tandem Landing Gear Set # BD500162, you were looking at, would work as a replacement. There are just bolts already installed where you'll mount your existing...
    view full answer...

  • Converting HappiJac 4200 and 4160 Manual Jacks into Electric Jacks
  • The replacement manual jack for the 4200 and 4160 jacks are the HappiJac Manual Truck Camper Jack System, part # LC736514-4. We have the electric upgrade kit for this part, so we have the upgrade for you. Because your camper is already pre-wired, you can get the version without the wiring, which is part # LC733960. I called HappiJac to get an installation manual for you. They did not have one, but they were able to get a wiring diagram for me, which I have emailed to you separately. I've...
    view full answer...

  • Stabilizer Scissor Jack with 5000lb Capacity and 24” Lift For Use With Power Drill
  • I have a solution for you, but when I called Lippert to confirm the size of the bolt on the Lippert Components Scissor Jack # LC285325 they informed me that this particular jack should not be raised or lowered using a power tool, but it does have a 3/4" nut. For that reason, I recommend instead going with the Stromberg Carlson # JSC-24-IND which works with a standard 3/4" socket. If you needed a matching socket for this jack, you can use the Ultra-Fab Speed Socket which is an adapter for...
    view full answer...

  • Recommended SnapPads For A Lippert PSX1 Electric Stabilizing Jack
  • I went out to our warehouse and test fit some SnapPads on the feet of the Lippert High-Speed Power Stabilizer Jack # LC298707 and found that the 6" square SnapPads were a fit. If your 2022 Forest River Vibe travel trailer only has one # LC298707 then you can order two of the single quantity # SN77FR, and if it has two sets of stabilizers then you can use the # SN99FR to get four SnapPads.
    view full answer...

  • Replacing Ultra-Fab Landing Gear With Lippert Landing Gear With High-Powered Motor
  • Thanks for all that good info, and what you have is the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010, which you can replace with a Lippert set with a high speed motor on you RV, though you will need to have new brackets welded on. The issue is that the Ultra-Fab has an uncommon 20-1/4 inch space between the mounting brackets, while Lippert and most others have landing gear with the standard 17-1/2 inches. So if you were okay with having new brackets welded on to meet the...
    view full answer...

  • Can Electric Trailer A-Frame Jack Be Powered By Power Port in Cargo Area of Tow Vehicle
  • The best way to power an electric A-Frame jack is with a trailer mounted battery and use the 12V accessory power feed from the trailer connector to provide a maintenance charge to the battery. If that isn't possible, the only other acceptable methods would be to tap the jack power wire into the 12V feed from the trailer connector or install a 7-way plug like # A7WCB on the jack power wire and directly use the 7-way on the tow vehicle to power the jack. The 12V accessory socket/power...
    view full answer...

  • Switch Replacement for Lippert Stabilizer Jacks 113407
  • For your Lippert stabilizer jack set 113407 on your trailer the correct replacement switch is the part # LC144214 for white or # LC387874 for black.
    view full answer...

  • How to use 12V Power Jack With Trailer That Doesnt Have a Battery
  • Since your trailer doesn't have a battery I am under the assumption that it has a 4-Way flat connection. Rather than installing a battery, battery box, and a 7-way with charge line circuit you can attach the 7-Way Molded Trailer Wire Connector # H20044 to the Stromberg Carlson Electric Trailer Jack # JET-5000 and use the vehicle battery to operate the jack. To do this simply connect the black wire of the connector to the black wire of the jack. The white wire of the connector will need...
    view full answer...

  • Jack Cover for Lippert Smart Jack LC89VR
  • For a cover for the Lippert Smart Jack # LC89VR you'd want the part # UF38-944020.
    view full answer...

  • What Type of Trailer Wiring Connector to Put on Wiring of Trailer Jack to Easily Power It
  • The type of trailer connector you'd need to install on the wiring of the Phoenix Electric Trailer Jack with Remote # UF38-944055 to allow it to plug into a vehicle connector and work would be a 7-way. 7-ways have a circuit designed for 12 volt accessories that runs to the vehicle's positive battery post. This is the pin in the 1:00 position if you were looking into the connector on a vehicle. So you could take the power and ground wire from the powered trailer jack # UF38-944055 and...
    view full answer...

  • Recommended Replacement Stabilizer Jacks For A 2011 K-Z Durango 1500
  • If you are needing to replace the stabilizer jacks on your 2011 K-Z Durango 1500, we will have 2 different styles. The Stallion Stabilizer Jacks # 288-01892-2 are a drop down style so they are easy to use, but they are only rated up to 1,000 pounds and have 22-1/4" of travel. The Lippert Scissor Stabilizer Jacks # LC285344, on the other hand, are scissor jacks so they will be a little more difficult to deploy. However, they are rated up to 10,000 pounds (combined) and have 30" of lift....
    view full answer...

  • What Capacity Electric A-Frame Jack for 7,000 lb Trailer
  • An electric A-frame trailer jack only needs to support the tongue weight of your trailer, which is approximately 10% to 15% of your trailer's GVWR. Almost all A-frame jacks nowadays are rated for way more than they'll ever be required to move, so you have a ton of choices for a 7,000 lb trailer, and I'll go over the best options for you. - The Best: Phoenix Electric Trailer Jack - A-Frame - 22-1/2" Lift - 4,000 lbs # UF38-944040 This baby is all about speed, travelling 10 inches...
    view full answer...

  • Stabilizers For Electric Automatic Landing Gear
  • While we do have an option for you, MORryde has told us the MORryde 5th Wheel Cross Brace Landing Gear Stabilizer # MR72AR should not be used with auto leveling landing gear. So what you would need instead, that is confirmed to work with your electric auto leveling landing gear, is an option from Lippert, the JT's Strong Arm Jack Stabilizer Kit . The only thing you need to know for the right kit is the distance between the landing gear legs; you will also need an adapter for your electric...
    view full answer...

  • Installation of etrailer Landing Gear
  • The Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs # RVLG-8HDL will simply mount to the weld-on brackets by being bolted on. While an online copy of the manual is not available for this specific landing gear, I did cut out a portion of the Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs # LG-183708 so you can take a look. In regards to the brackets you asked about, the Replacement Weld-On 5th Wheel Landing Gear Leg Bracket # LC113511 will work with...
    view full answer...

  • Using Vehicle Battery To Power Trailer Tongue Jack.
  • Great question. You technically could connect the Bulldog Powered-Drive Trailer Jack - Drop Leg - A-Frame - 21-3/4" Lift - 3,500 lbs - White # BD500188 to your vehicle lights, but we do not have the connector you would need to just plug into your tail light plug. I have a solution for this though. You can get the Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs # LC89VR. This unit comes with a 7 way connection, allowing you to plug in...
    view full answer...

  • Electric Camper Jacks HappiJac Swing-Out Extender Brackets Are Compatible With
  • The HappiJac Swing-Out Extender Bracket for Dual Wheel Chassis Truck Camper Jacks # HJ54FR (single) or Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems # LC182496 (double) are not compatible with the Atwood electric camper jacks. There isn't a similar extension for Atwood jacks, as they have been discontinued; the Swing-Out Extender # HJ54FR is only compatible with electric camper jacks from Happijac, the 8,800 lb HappiJac Electric Truck Camper Jack System - 34-1/2"...
    view full answer...

  • Recommended Replacements for Airstream 400914-03 Stabilizer Jacks
  • The ARK # ARK94FR stabilizer jacks could work for you, but you'll likely find they're too tall. The jacks measure 30 inches tall when fully extended or 19-1/2 inches tall when fully retracted. The existing 400914-03 jacks on your Airstream have a fully extended length of 19 inches, so these likely wouldn't be a good fit. The ARK # ARK34FR is height adjustable from 16-24 inches, so it would be more similar to your existing jack in that respect, so that's what I'd recommend going with....
    view full answer...

  • Lippert Stabilizer Jack is Clicking
  • There are a couple things you can do to try and figure out why your Lippert Components High-Speed Power Stabilizer Jack # LC298707 or # LC369774 is not working and is just making a clicking sound. Most likely it is a wiring or switch issue since you mentioned the battery was charged. Start by inspecting the wiring to at the switch to make sure it is not somehow damaged or if there are any obvious signs the wires are bad. Then test the wiring at the switch with a multimeter to see if...
    view full answer...

  • Where Do You Connect The Power Wire Of A Lippert Electric Trailer Jack?
  • The power wire for your Lippert Electric jack should be run to a dedicated 12v battery in your trailer, but it sounds like you have it wired to the break away switch battery. I recommend unwiring it from the break away switch battery as if you drain the battery by using the jack while it is unhooked from the vehicle you could run into an issue of the break away switch not working properly in an emergency situation. If you jack is the Lippert Power Stance Electric Trailer Jack with...
    view full answer...

  • How to Determine if Scissor Jack Will Fit Camper
  • The Scissor Stabilizer Jack # TJSC-24, which also comes in a 2-pack # TJSCHD-24 and a 4-pack # TJSCHD-24-4, is a universal fit so you would need to double check our measurements to ensure they fit your travel trailer. When they are collapsed they measure 5" tall and then they can extend up to 23-3/4" tall to help stabilize your trailer. I am attaching a link to our returns policy that you can reference in regards to your question about a possible return.
    view full answer...

  • Can Ultra-Fab Ultra Scissor Jacks Be Used without Leveling Blocks
  • The # UF48-979002 feature oversized footplates that are 4-1/2" wide by 9" long, so you could use them without leveling blocks. However, it's not uncommon for people to use leveling blocks like # A10-0918 or even wooden blocks under these jacks to provide extra stability (see photos). This is especially helpful in soft surfaces like grass or dirt. What you do want to make sure is that you chock your wheels to prevent your travel trailer from rocking and rolling when parked. For that,...
    view full answer...

  • Homemade Slide In Camper Lift Recommendations
  • For your horizontal clearance this will really come down to your specific truck as well. The Brophy Cable Camper Jacks have an offset lifting point that is designed to even with the legs of the jacks themselves. So if your truck has fenders that may bulge as it approaches the wheel wells, or your tires are wider than the outer fenders this would cause them to contact the stand and would not work. I personally would want to see at least 4" from the widest point to ensure enough clearance....
    view full answer...

  • How to Determine Correct Wheel Stabilizers for Tandem Axle Trailer
  • In order to determine the correct wheel stabilizer for your tandem axle trailer, you need to know the spacing you have between your wheels, as there isn't a standard spacing for trailers based on size. So all you need to do is take a quick measurement of the space between the tires at their closest point, which you'll use to determine the right stabilizers. - Up to 5-1/4" Wheel Spacing: Ultra-Fab Chock and Lock Wheel Stabilizers # UF21-001070 (can be locked with Master Lock Padlocks...
    view full answer...

  • Recommended 5th Wheel Tripod Stabilizer at Least 50" Tall and Compatible with Andersen Ultimate
  • I have the perfect solution for you! I recommend going with the Ultra-Fab 5th Wheel King Pin Tripod # UF19-950500 and then adding the Replacement Ball Assembly # UF19-001057. This will convert the tripod so that you can use it with the Andersen coupler adapter on your trailer. The Ultra-Fab tripod has an adjustable height between 37" and 54" tall. and has a 5000-lb pin weight capacity. In the event that you need a couple of extra inches more than the 54" provided by the Ultra-Fab, you...
    view full answer...

  • Replacement Front Jack Leg for Lippert Ground Control 3.0 Leveling System LC358590
  • Based on your troubleshooting efforts my contact at Lippert thinks there may be a bend in the right front jack leg of your Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC358590. Since the jack struggles with motor power but works when you manually crank it he thinks a damaged leg is the issue. You can use Replacement Lead Leg # LC362485 which works with your Ground Control # LC358590.
    view full answer...

  • Comparing Steel and Aluminum Ultra-Fab 5th Wheel King Pin Tripod Stabilizers
  • The Ultra-Fab 5th Wheel King Pin Tripod Stabilizer part # UF19-950200 would be best for harsher environments. The Ultra-Fab 5th Wheel King Pin Tripod Stabilizer part # UF19-950600 has a black coating which will also resists rust but if this coating wears off it can then expose bare metal. In regards to weight capacity vs pin weight, you'll still be using the landing gear to support the pin weight so the capacity of the stabilizer does not need to meet the pin weight of the trailer....
    view full answer...

  • Truck Camper Jack Replacements for 1998 Big Foot Truck Camper
  • Your truck camper jacks are more than likely obsolete due to the age of your 1998 Big Foot truck camper. So unless they have been updated already you will need a new set of jacks. You can replace them with a HappiJac Electric Truck Camper Jack System # LC736514-ELKIT. This kit will allow you to operate each jack individually or control them all at once via the remote control. You can also go with a HappiJac Manual Truck Camper Jack System # LC736514-4. To operate these you will...
    view full answer...

  • Can an Ultra-Fab Leveling Jack be Used to Change a Tire
  • We have better options because leveling jacks like the Ultra-Fab # UF48-979006 shouldn't be used to raise a vehicle. They're only for stabilizing despite their weight capacity. Instead you want something like the Powerbuilt bottle jack, part # ALL640405. It has plenty of capacity at 4,000 pounds and is for raising a vehicle like your X5 to change a tire. It's also pretty compact and not very expensive. Another option that's a bit of a step up is an electric scissor jack like part...
    view full answer...

  • Out of Stroke Error on Ground Control 3.0
  • The "Out of Stroke" error on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 4-Point Set # LC358590 and 6-Point Set # LC675817 means that they have reached the max height, can no longer lift so you need to relocate your trailer, or that you have bent or damaged jacks that will need to be replaced. So you'll need to check those jacks to see if there are any that are damaged, and replace as needed with one of the following: - Replacement Lead Leg for Lippert...
    view full answer...

  • How to Chock Tandem Axle Trailer While Using Leveling Blocks
  • The FasTen RV Leveling Blocks w/ Carrying Handle # CAM44512 can definitely be used to help jack up your travel trailer and then you can use the Stromberg Carlson Chock Wheel Stabilizers # SC47MR as chocks between the wheels to keep them stable just like standard chocks would. Attached is a review video of the stabilizers for you to check out!
    view full answer...

  • Replacement Heavy Duty Motor For Landing Gear On 2010 Keystone Raptor Toy Hauler
  • Your Raptor Toy Hauler likely has a landing gear setup similar to the one you were looking at: Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs # LC333964. If so, then the correct replacement motor would be Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893 which is rated for 5,000lbs, or you could go with Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor # LC196308 which is rated for 6,500lbs. This is the heaviest duty motor we have for...
    view full answer...

  • Lippert Ground Control 3.0 Touch Pad Displays "Please Wait And Then Turns Off
  • I spoke to Lippert and they said to check a few things. First, they did say to double check the battery and make sure it is not dropping under 12 volts. The system will always draw from the battery, even when attached to shore power, and the controller needs to stay constant. They mentioned that a common cause of this will be a ground issue. The green wire will be the ground so you will need to make sure this has a solid connection and not stacked with other grounds. The black wire will...
    view full answer...

  • Will The Lippert Ground Control Fit My 2020 Genesis Supreme 5th Wheel Toy Hauler?
  • The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System # LC675817 is a universal fitment and will fit most all 5th wheel campers that have a GVWR under 15,500lbs. For your 2020 Genesis Supreme 5th Wheel I am almost certain that you will need the 6 Point System # LC675817. To confirm this you will need to measure from the front jacks to the place where you will be mounting the rear jacks. If this measurement is over 20' then you have the correct kit. If your measurement...
    view full answer...

  • Difference Between Bulldog Velocity Series Electric Landing Gear Jacks
  • The only difference is that one of the Bulldog Velocity Series Electric Landing Gear Jacks comes with a remote control while the other does not. - With Remote Control: Bulldog Velocity Series Electric Landing Gear Jack # BD185400 - Without Remote Control: Bulldog Velocity Series Electric Landing Gear Jack # BD185402 Otherwise, both have a 12,000 lb capacity and are very fast jacks, lifting 20 inches in 60 seconds. I have added links to the instructions as well as a video review...
    view full answer...

  • Recommended Stabilizer Jacks for Off Road Use
  • This is difficult to answer without knowing the structure of the camper frame, how it's designed and the extended length you'll need, but I can certainly provide some general advice that will point you in the correct direction. I'm thinking a fold down type stabilizer jack would work well for you. A fold down stabilizing jack like # 288-01892-2 would be a good choice if its 22-1/4 inch extended length would work for you. When folded up, the jack will only extend by 4-3/8 inches below...
    view full answer...

  • Light Duty Brophy Cable Camper Jack Options
  • If you're needing the 67" max lift then you can get two of the 1,500 lb version # CJ74H. Same Max Lift just half the weight capacity. If you do not really need up to 67 inches of lift, you can get the # CJ31 that will have a Max Lift of 57 inches and a capacity of 1,000 lbs. These are both great options that are more light duty than the 3,000 lb jacks # CJ74. I've included some videos for you to check out if you wanted to learn more!
    view full answer...

  • Replacement Leg for 4160 Happijac Camper Jack
  • Since you have the Happijac 4160 setup on your Northern Lite truck camper the correct leg replacement is the part # LC736514.
    view full answer...

  • Do the Scissor Stabilizer Jacks Come with Install Hardware
  • The Scissor Stabilizer Jacks part # TJSCHD-24-4 do not come with installation hardware. That said, we do offer the self-tapping screws you'll need for this using part # FA1131822. In regards to quantity, you'll need a total of 16.
    view full answer...

  • Recommended 3500 lb Capacity Powered Jack for Horse Trailer
  • The etrailer brand # e69ZR jack you'd looked at would be a fine choice. The remote control is a nice feature and the fact that the jack plugs right into the 7-way trailer connector to operate would make this a very convenient choice. If you won't be using the trailer on a weekly basis, this is the option I'd recommend. If however you'll be using trailer more frequently, you'll be better off installing a battery on your trailer and using it to power a similar jack like # EJ-3520-BBX....
    view full answer...

  • Lippert Ground Control 3.0 Replacement Front Jacks
  • For the Lippert Ground Control 3.0 system # LC358590 or # LC675817 the correct front jack replacements is the part # LC362485. This works on the front and left jacks so you'd need a quantity of two. The price is available down below at the link. This works on the 4 jack and 6 jack Ground Control configurations.
    view full answer...

  • Auto Leveling Jack System Compatible With a 2019 Grand Design Reflection 150 295RL 5TH Wheel Camper
  • I do see that the Lippert Ground Control # LC358590 leveling system was an option on the 2019 Grand Design Reflection 150 295RL 5th wheel camper so you will not have any fit issues with the leveling system. There are some campers that are unable to use a leveling system due to components underneath the trailer but you will not have that on your Reflection. The SnapPad XTRA Jack Pads # SP54FR4 will secure themselves to the jack giving you a larger 11" pad. This saves you from having...
    view full answer...

  • Highest Capacity Scissor Style Stabilizer Jacks For a 2012 Artic Fox 25R Travel Trailer
  • The Ultra-Fab Ultra Scissor Jacks # UF48-979002 do have the highest capacity of the scissor style stabilizer jacks we carry at 6,500lbs per jack. This capacity is support capacity and does not have any lift rating. I would recommend using the Stromberg Carlson Chock Wheel Stabilizers # SC47MR since you are on such a slope. These will reduce the amount the trailer creeps down the hill.
    view full answer...

  • Stabilizer for Fifth Wheel Trailer That is Lived In
  • While there is an option for stabilizing your 5th wheel trailer that you are living in, the TrailerLegs Tire Saver Stands # 326-TRLLG-4 do require a tow vehicle to install and are also for when your trailer is in storage as opposed to being lived in. I recommend checking out the Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer - Steel - 31" to 54" # UF19-950500 because it is a great way to stabilize your trailer while also being very easy to use. It is for king pins that are 31"...
    view full answer...

  • Overall Length of the 24" and 30" Ark Drop Down Corner Stabilizer Jacks
  • I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks # ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6") extended. The Ark Drop Down Corner RV Stabilizer Jacks # ARK94FR are 497mm (19.5") collapsed and 774mm (30.5") extended. I have included the diagrams that they provided me for you to check out.
    view full answer...

  • Replacement Cover for Ram Electric Trailer Jack
  • The Ram electric trailer jack you referenced is very similar to the Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black # EJ-3520-BBX and the cover Replacement Cover for etrailer and Ram Electric A-Frame Jacks - White # EJ-3520-CVRW is compatible with that jack. I've attached a photo with the dimensions for you to confirm. You may also want to consider the Ultra-Fab Protective Cover for Electric A-Frame Jacks - Vinyl - 10-1/2" x 13-3/4" # UF38-944020 which is a confirmed...
    view full answer...

  • Replacement Lead Leg For Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System
  • Yes, we do have replacement parts available. If I am following you correctly, you are looking for the replacement lead leg for your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System, # LC675817. This will be part number, # LC305340.
    view full answer...

  • Which Scissor Jack Can Be Used for Changing Tires on 3500 lb Trailer
  • The scissor jacks we sell such as the # JSC-30-IND are meant to stabilize a trailer so it doesn't rock or pitch as you're walking around inside. The primary reason is that the jacks of this type that we carry aren't meant for changing tires is that the jacks are meant to be permanently installed on the underside of a trailer. If they're not bolted in place to the trailer frame, the jack could very easily slip off the jack and cause injury. A small bottle jack like # ALL640405 which...
    view full answer...

  • Correct Replacement Electric RV Stabilizer Jack Motor for 2011 Heartland Bighorn 3670RL
  • If you have the Lippert Components High-Speed Power Stabilizer Jacks like part # LC298707 then all you need to know to determine the correct replacement motor is the color of the support arms. If the support arms are black then you need the Replacement Electric RV Stabilizer Jack Motor part # LC138445 but if the support arms are yellow then you need the Replacement Electric RV Stabilizer Jack Motor part # LC352338.
    view full answer...

  • Should The Wheels Come Off The Ground When Leveling A Camper Or Trailer?
  • Your leveling system is not supposed to lift the wheels off the ground; this could exceed the capacity of your leveling system and cause damage and I do not recommend doing so. If you can make any adjustments to the legs then you will want to go ahead and do that, or depending on the model you may be able to reset the zero point. Feel free to let me know which system you have and I will track down the instructions for this process. If you happen to have the Lippert Ground Control 3.0...
    view full answer...

  • Will Lippert High-Speed Power Stabilizer Jack Work on Motorhome
  • The Lippert High-Speed Power Stabilizer Jack, # LC298707 and # LC369774 are not intended for use on motorhomes. However, you can try using it but you may find ground clearance to an issue. In addition, this has very specific mounting hole spacing on the frame of 68-11/16" from center-hole to center-hole. An option with a much better chance of working is the Ultra-Fab Power Twin II Electric Stabilizer. These can be used on motorhomes and the correct one will depend on the lift you need...
    view full answer...

  • Venture Landing Gear Rebuild Kits
  • We have Venture landing gear repair kits with part # LC146060 for the follow leg or part # LC146059 for the lead leg. To install the kits you'd want to take the legs off of the trailer.
    view full answer...

  • Replacement Stabilizer Jack for 2021 Jayco Jay Flight SLX 7 174BH
  • For a replacement jack for your 2021 Jayco Jay Flight SLX 7 174 BH I recommend the Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs # TJ01RT. This jack same mounting hole dimensions as your current jack at 3 inches apart on center. It has a 650 lb capacity per jack and extends up to 18". It is also sold as a set of 2 ,including the handle, which would be the # TJ01RT-HD. These would also be a great addition to the front of your travel trailer. I have attached a picture showing...
    view full answer...

  • Can the Super Grip Chock Wheel Stabilizers for Tandem Axles be used with Tire Covers on
  • I contacted the manufacturer about if the Super Grip Chock Wheel Stabilizers for Tandem-Axle Trailers # UF21-001091 can be used on wheels with tire covers in place. Per the manufacturer you can use the chock wheel stabilizers with cloth/vinyl wheel covers in place, but they recommend placing something (like a towel) in between the stabilizers and the tire covers to help keep the covers from tearing. One thing to keep in mind is that the Super Grip Chock Wheel Stabilizers for Tandem-Axle...
    view full answer...

  • Replacement for Bent Front Leg of Lippert Ground Control Auto Leveling System
  • Sounds like you have a Lippert Ground Control auto leveling system on your 2016 Highland Ridge Open Range like the # LC358590. For a replacement front leg you'd just need # LC362485 and you'd be set. The price for this is at the attached product links as well. I also attached a review video for this for you to check out too. If you have a different jack setup let me know and I'll see what we can get you set up with.
    view full answer...

  • How To Use Bulldog Electric Trailer Jack BD500199 On Trailer Without Battery
  • I do have a way for you to power your Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - Black # BD500199 without having to install a 12v battery on your 24' concession trailer, but I do not recommend hooking the battery for the break away system. This battery should stay dedicated to the break away system so it does not get depleted and cause the break away to not work properly if needed. Instead I recommend purchasing the Pollak Black Plastic, 7-Pole,...
    view full answer...

  • Stabilizer Jacks for R-Pod 195 Camper
  • We don't offer a combination leveler/stabilizer jack, but if you're wanting something in a stabilizer jack that is very sturdy, you can't go wrong with the ARK Drop Down Corner stabilizer jacks. They're available in a powder coat or a zinc finish, in 24 or 30 inch lengths. • 24 inch length in powder coat as part # ARK34FR or zinc as part # AR34FR • 30 inch length in powder coat as part # ARK94FR or zinc as part # AR94FR The manufacturer, ARK is located in Australia where off-road...
    view full answer...

  • Are Ultra-Fab Gooseneck and 5th Wheel Tripods the Same Thing
  • The Ultra-Fab Gooseneck Trailer Tripod Stabilizer # UF19-950450 is the exact same thing as the Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer # UF19-950500 with the only difference being the ball for the gooseneck coupler or the pin for the 5th wheel king pin. The only reason I can think that you would have an advantage with the 500 and the Replacement Ball Assembly # UF19-001057 is so that you have a connection for the Anderson Ultimate # AM3200 and the regular king pin if you...
    view full answer...

  • Lippert Front Stabilizer Jack Won't Go Down
  • On the Lippert High-Speed Power Stabilizer Jack # LC298707 you will want to test the different components to determine if it is the switch or possibly another component of your system. First I recommend running the jack manually to determine if you notice any spots where the jack seems to bind up. It the gears or shaft become damaged or bent this would cause the jack not to work properly. If you feel this then you will need to replace the jack. Next you will want to ensure that...
    view full answer...

  • Replacement Front Leg Solution for Jayco 355W Toy Hauler with Lippert Ground Control
  • You have a Lippert Ground Control 6 point kit installed on your RV and the best solution to fix what you have is the part # LC362485. This is the replacement leg portion without the motor for the front of the setup like you are needing. Lippert does not offer repair kits for what you have.
    view full answer...

  • What Jack Cover Fits My Ultra-Fab A-Frame Jack # UF97FR?
  • Yes! For a great cover to protect your Ultra-Fab Electric A-Frame Jack # UF97FR, you need the Ultra-Fab Protective Cover for Electric A-Frame Jacks # UF38-944020. This cover is specially designed to protect the jack motor from rain, snow, and dirt.
    view full answer...

  • What is Lowest Height Setting of Brophy Cable Camper Jacks # CJ74
  • When the Brophy Cable Camper Jacks # CJ74 are cranked all the way down the bracket that holds the camper will be 17 inches from the ground. The bracket length is 26-1/2 inches long.
    view full answer...

  • Replacement Trailer Stabilizer Jack For 2019 Keystone Hideout With J-2500 Jack
  • Yes, the Ultra-Fab Ultra Scissor Jack # UF48-979006 will work as a replacement for your damaged stabilizer on your 2019 Keystone Hideout 274LHS. This jack has a universal style bolt mounting plate and an oversized footplate to prevent it from sinking into loose soil and gravel as easily. You will need to reuse your factory hardware or source new hardware if it is damaged. If you do not already use one the Ultra-Fab Speed Socket Power Drill Adapter # UF48-979005 will make raising and...
    view full answer...

  • Replacement Rubber Plug for Top of Lippert Powered A-Frame Jack LC285318
  • Yes for just the rubber plug for the top of the Lippert Jack part # LC285318 that you referenced you'd want the part # LC733924.
    view full answer...

  • Troubleshooting LCI Trailer Jack 1817941
  • I'm sorry to hear that you're having trouble with your trailer jack, but I am happy to help you troubleshoot it. I assume that you have an auxiliary battery on your trailer to power the jack since you said the battery is new. If you don't have a battery on the trailer, then make sure that the jack is hooked to a tow vehicle that has a 12v power source at the back of the 7 way trailer connector. The first thing I would check is the light on the jack. If the light is coming on then the...
    view full answer...

  • RV Scissor Jack Solution with Round Upper Mounting Bracket
  • There isn't a way to rotate the mount in relation to the foot direction of the stabilizer scissor jacks part # JSC-24 and since none of our options are setup like that our best solution would be the # LC285344 which has a round mounting bracket on the top instead.
    view full answer...

  • Can etrailer EJ3527-BBX Trailer Jack Be Powered From 7-Way Trailer Connector on 2020 Ford F-150
  • The etrailer brand # EJ3527-BBX is equipped with a 7-way plug that can be plugged into the 7-way trailer connector on your 2020 Ford F-150. This being said, for more reliable operation, it's best to install a battery on the trailer and run a powered jack from that. The etrailer # EJ-3520-BBX jack is designed to be wired directly to a trailer mounted battery. You can wire the 12-volt feed from the 7-way to the trailer mounted battery. It won't charge the battery completely if it gets...
    view full answer...

  • Replacement Parts Available for Lippert Smart Jack
  • If you're looking for the hard plastic piece that covers the manual override on your Lippert Smart Jack Electric Trailer Jack # LC643589, you can use part # LC733925. Aside from that and the drop leg # LC405217, Lippert does not offer any other replacement parts for this jack.
    view full answer...

  • Replacement 500V 30A Fuse for RAM Power Jack
  • We actually carry the replacement fuse part # EJ-FUSE for RAM or etrailer.com trailer jacks, like part # EJ-3520-BBX. With that being said, I have reached out to RAM about this in the past and they have said that there isn't anything special about the fuse so if you are able to find one at your local home improvement store, like one that you mentioned, then it will work just the same.
    view full answer...

  • Recommended Electric Tongue Jack for 7,000 Lb Trailer
  • The Electric Jack part # EJ-3520-BBX is what I recommend using as it's an excellent economical upgrade option. If you are replacing an exiting electric jack then just run the power wire to the battery, secure the flange to the frame, and you're done. If you are switching from a manual to an electric jack then you might want to use part # EJ-3527-BBX since it comes with a plug for the vehicle to power it. The 3,500 b capacity will be more than enough for a 7,000 lb trailer since it only...
    view full answer...

  • Replacement Tongue Jack for a Coachmen Catalina 263RLS 50th Anniversary Edition
  • We have a great option for you. Unfortunately we do not have anything that tells us what jack you currently have but from your make and model it looks like you need an A-frame jack. I recommend the Ultra-Fab Electric A-Frame Jack # UF97FR. The Ultra-Fab Electric A-Frame Jack # UF97FR will fit 2" or 2-1/4" spacing, has 23-1/2" of total lift (combination of screw travel and drop leg) and can lift up to 3,500 lbs which will be more than enough for your 5,700 lb. dry trailer because the...
    view full answer...

  • Dimensions From Bottom of Housing and Motor to Bracket of etrailer 3,500 lb Electric Jack
  • We do have the measurements you are looking for on the etrailer 3,500 lb Electric Jack. From the bottom of the housing to the bracket the measurement is 14-1/2 inches, and from the bottom of the motor to the bracket the measurement is 10 inches. These measurements are the same for both versions of the jack, with the only difference being the color they come in. - Black: Electric Jack with Footplate # EJ-3520-BBX - White: Electric Jack with Footplate # EJ-3520-WBX
    view full answer...

  • Are Weight Limits Combined or Per Jack for Stabilizing Scissor Jack
  • The stabilizing jacks are all made overseas, and in regards to the capacities, they are on a per-jack basis. So the Scissor Stabilizer Jacks with Handle - 18-3/4" Lift - 10,000 lbs - Qty 4 # TJSCHD-24-4 have a 2,500 lb capacity per jack. The Lippert Scissor Stabilizer Jacks with Handle - 24" Lift - 12,000 lbs - Qty 2 # LC285326 have a 10,000 lbs capacity (5,000 lbs per jack) And the Stromberg Carlson Leveling Scissor Jack Set - 24" Lift - 10,000 lbs - Qty 2 # JSC-24 has a 5,000...
    view full answer...

  • Difference Between etrailer Landing Gear Jacks RVLG-8HDL and RVLG-8000
  • The difference is that the # RVLG-8000 does not come with a handle and the # RVLG-8HDL does come with one. Aside from that it's the exact same jacks. We don't offer replacement legs for them so if you need new legs best toption is the # RVLG-8HDL which will give you a new gear box as well.
    view full answer...

  • What To Use If The Manual Override Crank Handle For A Stromberg Carlson Electric Jack Is Too Long
  • The center portion of the Replacement Manual Crank Handle for Stromberg Carlson Electric Trailer Jacks Item # SC94VR is roughly 8-1/2". As far as putting a bit on a drill, you would have to take the handle to an auto part store to see if they have one that will match it. Keep in mind you could potentially lose the bit inside the housing if it is not secured to an extension. What I would do if it was mine is cut the rod just below the first bend, grind two sides flat, about a 1/2" long...
    view full answer...

  • Replacement Bottom Cover For A Lippert Electric Trailer Jack
  • The correct replacement bottom cover for your Lippert Electric Trailer Jack # LC285318 is the Replacement Bottom Jack Cover with Light Lens # LC23UD.
    view full answer...

  • Landing Gear Replacement for Keystone Laredo that Allows Reusing Motor
  • If the brand of landing gear you have now on your Keystone Laredo is a Ram brand then yes you could reuse it's motor with the # RVLG-8HDL. But most likely you have a Lippert set of landing gear based on what typically they used so instead the part # LC333966 would be what you'd want instead so that you could reuse the motor.
    view full answer...

  • Electric A-Frame Jack Recommendations for a Utility Trailer
  • If you already have a battery on your utility trailer and you really like how the etrailer Electric Jack w/ Footplate # EJ-3520-BBX performs (thank you by the way) then I recommend just going that another one. Since it has a lift capacity of 3,500 lbs you will have more than enough power to get the job done. If you don't already have a battery on your utility trailer then I recommend using the Trailer Valet JXC instead. This comes in a 2K # TV54FR and 5K # TV94FR version for an A-Frame...
    view full answer...

  • How To Support Slide-Out On 1998 Monaco Diplomat
  • The Ultra-Fab Slide-Out Supports for Motor Homes, # UF19-960003 that you linked to are adjustable supports that mount between the ground and the frame of slide out to reduce slide-out sag. This adjustment ranges in height from 26" to 47". This has a 4-3/4" inside measurement U-channel bracket that the RV's extension tubes rest against. This bracket straddles the frame member and tightens against it for secure positioning. The # UF19-960003 is a quantity of 2 each with combined weight capacity...
    view full answer...

  • Replacement for Lippert PSX2 Stabilizer Jack 695602
  • I do have an option for you but we don't carry the Lippert PSX2 Stabilizer Jack 695602. Instead, we carry the Lippert High-Speed Power Stabilizer Jack part # LC337199 for no switch, part # LC369774 for a white switch, or part # LC298707 for a black switch. These are very similar jacks to what you have now expect they have a single motor design. The footprint and mounting will be the same.
    view full answer...

  • Replacement Stabilizer Scissor Jack For a 2016 Coachmen Clipper 17RD
  • Yes, the Scissor Stabilizer Jack # TJSC-24 will work on your 2016 Coachmen Clipper 17RD. It is a universal bolt on stabilizer jack that will lift to a height of 23-3/4". I always recommend using only dry lubricants on these parts as wet lubes and grease will collect dirt and make it harder to use. The LubeMaster Dry Silicone Spray # RM-747 would be the type I recommend.
    view full answer...

  • Recommended Replacement Extend/Retract Switch For Lippert Electric Trailer Jack
  • I would be happy to help! The replacement extend/retract switch for your Lippert Power Jack # LC285318 is not available by itself, so you will need the Replacement Top Cover for Lippert Electric Trailer Jack - Black # LC285160 which includes the new extend/retract switch, and new on/off switch for the light. I included a video of the # LC285160 for you to take a look at.
    view full answer...

  • Solution for Replacement Controller for Discontinued Atwood Leveleg System
  • I have a complete replacement option for you, but when Lippert bought out Atwood they discontinued the Atwood Leveleg parts. Unfortunately, a replacement controller is no longer available. Instead, I recommend replacing your system with the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set # LC358590 if you have less than 20' between the front and rear leveling jacks. If you find that you have 20' or more between the front and rear leveling...
    view full answer...

  • Recommended King Pin Tripod Stabilizer For A Grand Design Reflection 150 Series 29RL
  • I recommend the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer # UF19-950001 for your Grand Design Reflection 150 Series 29RL. This tripod has a weight capacity of 5,000-ls, which should be more than enough to support the pin weight of your Grand Design Reflection. This tripod extends from 37" to 50" to give you plenty of range in height. Additionally, if desired, you could also use the Leg Extensions for Ultra-Fab 5th Wheel Kin Pin Tripod Stabilizer # UF19-950002, which will give...
    view full answer...

  • Electric Trailer Jack Recommendations for a 2014 Coleman 262BH Camper
  • Based on the size of your 2014 Coleman 262BH camper, I recommend going with a jack rated for 3,500 lbs. This is the most common size electric jack out there, so the good news is you have quite a few options. Keep in mind, the jack does not have to be rated for the weight of your trailer because it is only lifting the tongue weight of your trailer, but I will admit that jack weight capacities really don't make much sense for trailer tongue weights or gross vehicle weights. It looks like...
    view full answer...

  • Axle to Pavement Clearance Needed for 326-TRLLG-4 TrailerLegs Storage Jacks
  • The # 326-TRLLG-4 TrailerLegs are designed for axle to ground clearance of at least 10-1/2 inches. If you have less clearance than that, they won't work correctly for you and to achieve the same thing you'd need to put the RV up on jack stands like # PTW41021 high enough that the tires aren't touching the ground. We unfortunately don't offer a shorter version of the TrailerLegs.
    view full answer...

  • USA Manufactured Trailer Wheel Chocks
  • The Ultra-Fab # UF21-001095 wheel chocks are made in China. If you'd prefer a chock manufactured in the US, I'd recommend the # 337WC24483 from Buyers Products. If you click the provided link, you can see a video of my buddy Randy demonstrating the chocks I recommedned.
    view full answer...

  • Automatic Leveling System for 2019 Grand Design XLS 22RBE - Easy Installation
  • The Lippert # LC369774 number that you referenced is an improved stabilizing system that includes motors to operate the stabilizers. These are typically installed in the back, as the front of the trailer is stabilized by the tongue jack. They are a significant improvement over manual scissor jacks. The Lippert # LC672136 Electric Ground Control leveling system that you referenced by name is a leveling system. The components basically take the place of your corner scissor jacks, and...
    view full answer...