What is the Distance Between Weld Stops on Stromberg-Carlson Landing Gear Set LG-1
Updated 08/11/2020 | Published 07/08/2015
Question:
what is the distance between the clips or extrusions on this jack?, the distance between on my existing landing gears is 17 1/2 inches, top of top clip to bottom of bottom clip, this is important because my u clips are welded on and replacement landing gears need to be the same. My existing gears that failed were made by Fulton, any help will be greatly appreciated, thanks.
asked by: Carroll D
Expert Reply:
The weld stops on the legs of Stromberg-Carlson landing gear set # LG-1 are indeed 17-1/2 inches measured from the top of the top one to the bottom of the bottom one. If you look at the diagram I have included you will see that they have measured from the top of one to the top of the other and that is 16-1/2 inches. Since the weld stops are 1 inch tall the measurement is 17-1/2 inches just like what you need!
Product Page this Question was Asked From
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Camper Jacks
- 5th Wheel Camper
- Landing Gear
- Steel
- 5001 - 6000 lbs
- Electric Jack
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: awning
- Search Results: landing gear motor
- Search Results: atwood landing gear
- Search Results: landing gear
- Search Results: dual motor landing gear
- Search Results: awning fabric
- Search Results: stromberg carlson landing gear
- Shop: Stromberg Carlson Dual Power Conversion Kit for RV Landing Gear w/ 29-1/2" Legs - 5,500 lbs
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Shop: Lippert Manual Landing Gear Set w/ Handle - 37" Lift - 6,000 lbs
- Shop: Mach-C Everest Variable Speed RV Air Conditioner System - 18K Btu - Ducted/Non-Ducted - R32 - White
- Shop: Mach-C Everest Variable Speed RV Air Conditioner - 18K Btu - Ducted/Non-Ducted - R32 - AC Unit Only
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Replacement Motor for Stromberg Carlson Electric Landing Gear - 5,500 lbs
- Video: All You Need to Know About the Landing Gear Set
- Q&A: Where do the Brackets Install in Relation to the Weld Stops on the Reese Landing Gear # RP500708
- Q&A: Replacement AC System for a Dometic Penguin II w/ Heat Pump 651916H751C0-M
- Q&A: Picking Out Landing Gear Replacement for Legs that Have 19.5 inches Between Weld Stops
- Q&A: Landing Gear Replacement Recommendation for 1997 Fleetwood 5th Wheel w/ RBW Landing Gear
- Q&A: Replacement Landing Gear and Equalizers for a 2008 Keystone Cougar 5th Wheel
- Q&A: Troubleshooting 5th Wheel Landing Gear That Retracts But Wont Extend
- Video: Feature Breakdown: Stromberg Carlson Electric Landing Gear Set
- Q&A: Motor Kit Needed to Convert etrailer Landing Gear RVLG-8000 to Powered
- Video: Let’s Check Out the Stromberg Carlson Dual Power Conversion Kit for RV Landing Gear
- Video: Feature Review Replacement Follow Leg for Stromberg Carlson Landing Gear
- Video: Complete Breakdown of the Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Video: An In-Depth Look at the Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Video: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear Spec Review
Jim B.
8/1/2020
Is the Stromberg Carlson LG 1 an appropriate replacement for a 2010 Jayco 28.5