See what our Experts say about this etrailer Camper Jacks

• Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
  I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or...
  view full answer...
  
• Recommended Replacement Landing Gear Set for a 2004 Keystone Cougar 5th Wheel Trailer
  When you are looking for replacement landing gear the 2 big things to take into consideration are the weight of your trailer and the weld stop locations on your current setup. Since the GVWR of your 2004 Cougar is 10,300 lbs our Landing Gear Set w/ Handle # RVLG-8HDL that you referenced can handle the weight capacity of your RV. Keep in mind that some of the weight of your trailer is still supported by the axles and tires so a landing gear setup doesn't need to be rated for the total GVWR...
  view full answer...
  
• Replacement Landing Gear for 2009 Heartland Sundance 5th Wheel Trailer
  The 8K Landing Gear Set w/ Handle # RVLG-8HDL should fit just fine as it uses the standard weld stop locations measuring 15-1/2" or 17-1/2" for the mounting brackets. I don't know what the current bracket dimensions are for your 2009 Heartland Sundance but you can quickly verify if this is compatible by measuring the space between your mounting brackets. If it is 15-1/2" or 17-1/2" then you are good to go! This landing gear comes with a manual hand crank and you have the option to add...
  view full answer...
• Replacement Powered Landing Gear for Horse Trailer to Replace Atwood
  Hey William, the closest jack set we have to your Atwood setup would be the Reese powered landing gear part # RP500708 which is the only dual motor setup we have that has same mounting bracket dimensions as what you currently have. You would need to replace the switch setup you have now with what comes with this kit but aside from that it's a similar setup. Atwood got out of the jack business several years ago so there isn't an exact replacement available which is why this is your best...
  view full answer...
• Replacement Landing Gear for 2005 Jayco Designer
  Hello again Terry; I would double check your measurements there. The difference between the inside and outside measurement is typically 2", with 1" for the weld stops. We have the Stromberg Carlson Electric Landing Gear Set # LG-4 which has an inside measurement of 19-1/2" and outside of 21-1/2" with lines up with one of your measurements. All of the others like the # RVLG-8HDL we talked about before follow the industry standard and are 15-1/2" inside and 17-1/2" outside. If nothing lines...
  view full answer...
• Availability of Motor for Bulldog Tandem Landing Gear Set
  Hi Terry; we don't have a motor that is designed to fit the Bulldog Tandem Landing Gear Set # BD500162. It is possible some of the motors we carry fit but they haven't been tested. The only motor we have seen used on this landing gear was discontinued. What I recommend instead is the Landing Gear Set w/ Handle # RVLG-8HDL. You can add a motor to this landing gear using # LG-142178. The motor capacity is lower at 5,500 lbs but it is probably not an issue for your 2005 Jayco Designer 5th...
  view full answer...
• Replacement for Atwood MPD 71125 5th Wheel Landing on 5th Wheel Camper
  Since Atwood is no longer in the landing gear business it is basically impossible (unfortunately) to get just a replacement leg. The part number that you gave me actually is a document that shows the various parts for Atwood landing gear, but nobody has information as to what those replacement parts are the equivalent of. Because of this I recommend replacing the landing gear on your 5th wheel trailer. This gives you some peace of mind that you won't have to replace any parts in the near...
  view full answer...
• Replacement Landing Gear For A 2008 Weekend Warrior Road Warrior 5th Wheel Toy Hauler
  Hey Bob, Landing gear components aren't all interchangeable between brands so I'd need to know the exact model to find replacement parts for your current system. If you're just wanting to replace the landing gear as a whole then I'll need to know the the spacing for the weld stops. For example, the Landing Gear Set w/ Handle # RVLG-8HDL you were looking at has a 15-1/2" inside and 17-1/2" outside measurement, which is a pretty common spacing. If your spacing differs then you'll have...
  view full answer...
  
• Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
  Bulldog Tandem Landing Gear Set # BD500162 is a great option for a manual set to replace the landing gear on your Keystone Laredo. I have linked a video review for you. The handle is not included so use # BD500203 to add the crank handle. For an electric set you could use # RVLG-8HDL and add motor # LC142178 and, if you don't already have one, a switch # LC145236.
  view full answer...
• What is the Difference Between the Landing Gear Set RVLG-8HDL and RVLG-8000?
  Hey Bobby! As far as the jacks go for item # RVLG-8000 and item # RVLG-8HDL there is absolutely nothing different. The item # RVLG-8HDL comes with the manual handle that I have attached a picture of below. That is the only difference. If your 2019 Cherokee Wolf Pack toy hauler has brackets that are 2" tall then you most likely have the standard weld stop measurements of 15-1/2" inside to inside. I have attached a photo so you can compare these dimensions to your current set up. If these...
  view full answer...
• 5th Wheel Landing Gear Replacement for 2011 Wildcat by Forest River Model 31TS
  You could use the Landing Gear part # RVLG-8HDL as a replacement for what you have now on our 2011 Wildcat by Forest River. This will bolt right up in place of what you have and has plenty of capacity at 8,000 lbs so it will operate easily.
  view full answer...
• Option for Upgrading Atwood Landing Gear from Manual to Electric Set
  The Atwood line of landing gear jacks has been discontinued for some time so to upgrade to an electric set you'd have to go with new landing gear like the # RVLG-8HDL and then install the motor part # LC142178 with it and you'd have a very similar setup but with a motor that will make raising and lowering the trailer easier.
  view full answer...
• Replacement Landing Gear for 1995 Sierra by Cobra
  For replacement landing gear on your 1995 Sierra by Cobra you can use the Landing Gear Set # RVLG-8HDL. Since nothing matches your weld stop measurements you will also need to weld on new brackets # LC113511. This landing gear has a capacity of 8,000 lbs and uses the standard inside 15-1/2" and outside 17-1/2" measurements found on most modern landing gear. If you want to add a motor it is available separately # LC142178.
  view full answer...
• Replacement for Atwood Landing Gear on 2004 Fleetwood Wilderness 5th Wheel Trailer
  I reached out to my contact at Lippert who said that the Atwood line has been discontinued and they don't have any replacement parts for it. Since this is the case you'll need to replace your Atwood jack. Was this for the landing gear or for a stabilizer jack? If you can let me know this I can recommend a replacement for you.
  view full answer...
• Dimensions of etrailer Brand RVLG-8HDL and RVLG-8000 Replacement 5th Wheel Landing Gear
  The only difference between the # RVLG-8HDL and the # RVLG-8000 is that the # RVLG-8HDL includes the manual crank handle, while the # RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended Height of 53-1/4 inches The tabs for the mounting straps measure 17-1/2 inches from the top of the top most tab to the underside of the lower tab. From the underside of the top tab to the top of the lower tab is 15-1/2 inches. I've shown these dimensions...
  view full answer...
  
• Motor for etrailer Landing Gear Set w/ Handle
  Hi Bob; are you referring to the Landing Gear Set w/ Handle # RVLG-8HDL you purchased a little over a year ago? If so, the correct motor is the Lippert Venture 5th Wheel RV Landing Gear Motor # LC142178. If you were looking for something else please let me know in the comments below.
  view full answer...
• Distance From Top of Weld Stop to Crank Shaft for the etrailer Landing Gear Set
  Hey Chad, From the top weld to the middle of the crank shaft is 6" for the Landing Gear Set # RVLG-8HDL. If you were talking about the rod at the top of the gearbox then that would be 8-1/2". Attached are some dimensional photos for you to check out.
  view full answer...
• Replacement Parts for Landing Gear
  Hey Dennis. I did not get anything back when I searched the 276S02-643252 pn you gave me. Who's the manufacture of your landing gear and do you have any other part numbers off of it? You can add this information and any other questions you have where it says Reply to Jerred H and I'll be happy to answer them.
  view full answer...
• Difference Between 8,000 lb Landing Gear RVLG-8HDL & RVLG-8000
  The only difference between these two 8,000 lb landing gear sets - other than price - is that one comes with the crank handle and the other does not come with the handle. - Comes With Crank Handle: Landing Gear Set w/ Handle # RVLG-8HDL - Comes Without Crank Handle: Landing Gear Set # RVLG-8000 Apart from that, these are 100 percent the same landing gear.
  view full answer...
• How to Choose Replacement Landing Gear for 5th Wheel Trailer
  The first thing you want to do before you find a replacement is to check the rating on your current landing gear. You want the new landing gear to be rated for at least the same amount. You will also need to measure the weld stops to make sure they match up so you won't have to do any welding. For example, the Landing Gear Set w/ Handle # RVLG-8HDL you were looking at is rated for 8,000 lbs. The distance from the top of upper weld stop to bottom of lower weld stop is 17-1/2" which is the...
  view full answer...
  
• Can The Gearbox For The etrailer Landing Gear Set Be Mounted Horizontally
  The gearbox # RVLG-RDBOX for the Landing Gear Set w/ Handle # RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place match up perfectly for both positions (pictured below).
  view full answer...
  
• Are Replacement Parts for Atwood Landing Gear Available or Will Another Brand Fit
  The division at Atwood that handled the jacks and landing gear was sold off to Lippert so direct replacement parts are not available. But it is likely that the gear box and motor of another brand will still fit. And yes, the gear box and motor do just sort of hang there. Gear box # RVLG-RDBOX is one possible option. With it you can use motor # M1230. For the driver leg D shaft there were 3 possibilities for Atwood landing gear depending on which model it is (standard duty, heavy duty,...
  view full answer...
• Landing Gear Replacement for 2021 Forest River Wolf Pack 365 Pack 16
  Yes, based on the distance between the welded on brackets of your camper the etrailer landing gear set part # RVLG-8HDL will fit on your 2021 Forest River Cherokee Wolf Pack. The motor normally used with this kit is the part # LC142178. If the motor you have looks like this (most likely it will) then it would work with this.
  view full answer...
• Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
  Good news! I was able to go out to the warehouse and measure the etrailer landing gear # RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld stops is 15-1/2 inches. I have linked a dimensional diagram to this page for you to better see where I measured. I have linked this product to this page for your convenience.
  view full answer...
  

Do you have a question about this Camper Jack?