Recommended A-Frame Trailer Jack For A 2013 Jayco Jayflight 19RD

Question

Question:

have 2013 jayco Jayflight 19Rd... specs say about 3800 pounds dry, 6200 Gross. tongue under 600. will this fit and operate properly? any recommendations on something a bit more sexy or workable? thanks

asked by: Gene T

0

Expert Reply:

The Ultra-Fab Electric A-Frame Jack # UF38-944014 will work just fine for your 2013 Jayco Flight 19RD. This jack has the capabilities to lift up to 4,000-lbs of tongue weight, which is plenty for your trailer.

While this jack will work for you, I recommend the Stromberg Carlson Electric A-Frame Tongue Jack # JET-2500. This jack is going to be closer to your tongue weight, while still offering plenty of remaining capacity.

expert reply by: Bryce D

0

Answer 1

To check the pins on the vehicle side 7-Way, you can use a circuit tester or the volt meter. The circuit tester will show you if a signal is coming through on the pin you are testing while the volt meter will tell you that and how much voltage is…

view full answer...

Answer 2

For a 3500 lb Electric Jack, I recommend the Bulldog Powered-Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 3,500 lbs - Black #BD500187. This jack uses a 12 volt system, so it is compatible with your 7-way although a battery is always a…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Tyler, great question - and it’s definitely more than cosmetic. The etrailer electric trailer jacks #e72QV and #e22QV are mechanically identical 3,500 lb jacks. Same motor, same lift height of 18", same 7-way plug power. The only difference is…

view full answer...

Answer 8

Hey Larry, welcome back! The distance your looking for is 23-1/4". From the top of the A-frame mounting bracket to the top of the motorhead on our etrailer Electric Trailer Jack item #e79GV is exactly 23-1/4". The jack measures 33"…

view full answer...

Answer 9

Hello Danny, I’m really glad you mentioned the Equalizer! When sway is the issue, that one and the Weigh Safe are definitely my go-to options. They both have 4 point sway control, with straight spring bars and frame brackets. They can be a little…

view full answer...

Answer 10

Hey Mark! All three of these etrailer jacks - the #e72QV 3,500 lb, the #e22QV 3,500 lb with SnapPad, and the #e82QV 5,000 lb with SnapPad - are powered directly through your truck’s 7-way plug. So with your Silverado’s factory 7-way, you can simply…

view full answer...

Answer 11

Hi Mark! From the bottom of the mounting plate to the bottom of the foot plate on the etrailer Electric Trailer Jack w/ 7-Way and SnapPad - Drop Leg - A-Frame - 18" Lift - 3.5K #e22QV you are looking at just under 9" (8-7/8" to be…

view full answer...

Recommended A-Frame Trailer Jack For A 2013 Jayco Jayflight 19RD

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching