Does the Kodiak 10 Inch Hub and Rotor Assembly Come with Bearings and Seals
Published 09/03/2021
Products Featured in This Question
Question:
I wasreading the response and these are exactly what I need. It states it is is the bearings, seals, and cap. I dont see a picture of the caps and wanted to make sure before i ordered. So my question really is does it come with the caps for over the zero fitting?
asked by: Ben W
Expert Reply:
We do have the parts you're needing, but the Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs # KHR10D only comes with the races included; the bearings, grease seals and caps are not included and must be purchased separately.
You can use the Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal # BK2-100 which will give you the bearings to fit in these hubs and also includes the tang washer and cotter pin. The only other part you would require are the grease caps, which are available with the Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2 # RG04-040.
If you wanted to purchase the parts individually then you'd need the grease seals plus the # L44649 and # L68149 bearings, grease seal # RG06-050, the Replacement Spindle Washer - Tang Type for E-Z Lube # 5-101 and a cotter pin # 165649.
Product Page this Question was Asked From
Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Trailer Hubs and Drums
- Hub with Rotor
- Standard
- L68149 / L44649
- Marine Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Kodiak
more information >
Continue Researching
- Q&A: How to Determine Correct Replacement Hub for Boat Trailer
- Shop: DeeMaxx 10" Hub/Rotor Assembly - 5 on 4-1/2 - Maxx Coating - 3,500 lbs
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Kodiak 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Search Results: reliable oil hubs
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer tires and wheels
- Video: Measuring To Choose The Right Trailer Axle
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: What is the Best Grease for Trailer Bearings
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Search Results: trailer jack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer wiring
- Shop: Brake Controller
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Video: In-Depth Review of the Easy Grease Trailer Idler Hub Assembly for 3.5K Axles
- Video: Step-By-Step Installation for the etrailer Hub Bearing Kit - Utility Trailer
- Search Results: trailer leaf springs
on Trailer Hubs and Drums
