Tip for Reducing Wind Noise of MaxxTow Ladder Rack MT70232

Question

Question:

When traveling at speed, the loud humming is irritating, especially on long trips. Is there anything I can do to mitigate this?

asked by: Steven A

0

Expert Reply:

The best option we have to cut down on the wind noise of your MaxxTow Ladder Rack MT70232 would be with a fairing that would attach to the forward most bar and would direct most of the wind around where it's making noise. For that the best option is the Rhino-Rack fairing # RRRF4 which measures 50 inches long and will easily attach to the front bar.

expert reply by: Jameson C

0

Answer 1

Yes, you can! We've spoken to Curt about this exact issue before and we do have a solution. The Curt Hitch item #C15398 is designed for the 2013 Toyota Tundra's that come without a factory hitch. However, it will fit the Tundra's that…

view full answer...

Answer 2

Yes, the Curt Class V Trailer Hitch, item #C15398, will fit on a 2010 Toyota Tundra TRD, as long as it does not have a factory installed hitch on the vehicle.

view full answer...

Answer 3

Yes, The Curt Trailer Hitch Receiver #C15398 is confirmed to fit your 2011 Toyota Tundra after you remove the factory installed hitch. The trailer hitch has a bolt on installation with no welding required. It has a black powder coat finish over a…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

Hey David! Unfortunately, the Curt CrossWing #C92DR isn't compatible with the Curt Helux Shock-Absorbing Pin Box because of the Helux's articulating design. Instead, I recommend the Andersen Ultimate 5th Wheel Connection #3220. It's…

view full answer...

Answer 10

Hey Brady, Brophy in the past has told us that the tie downs part #HSWB don't have a weight capacity but you would want to make sure you use them only with campers that were designed to fit the bed length of the truck. The turnbuckles part #TDHP…

view full answer...

Answer 11

Thanks for reaching out Kathleen. The TorkLift Custom Frame-Mounted Tie Downs #TL66ZV include the complete set of front and rear tie-downs for both the driver and passenger sides of your truck. This kit is the correct fit provided your Toyota Tacoma…

view full answer...

Answer 12

It sure does Joe. Since your 2018 Ford F-250 has the 6-3/4' bed, you'll need the TorkLift Talon Truck Camper Tie-Downs item #TL22SV. This is a set of front and rear tie downs that are designed to work with the factory hitch. They will not…

view full answer...

Tip for Reducing Wind Noise of MaxxTow Ladder Rack MT70232

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching