Will Curt Crosswing C92DR Work With Curt Helux Shock Absorbing Pin Box?

Question

Question:

Will the Curt Crosswing C92DR work with the Curt Helux Shock-Absorbing pin box?

asked by: David

0

Expert Reply:

Hey David!

Unfortunately, the Curt CrossWing # C92DR isn't compatible with the Curt Helux Shock-Absorbing Pin Box because of the Helux's articulating design.

Instead, I recommend the Andersen Ultimate 5th Wheel Connection # 3220. It's another lightweight option that mounts directly over a 2-5/16" gooseneck ball and can work with the Helux when paired with the required Andersen Helux Lockout Kit # AN64ZR.

The Andersen also offers up to 9" of offset (5" from the base and 4" from the coupler adapter), which can help provide additional cab clearance, especially with short-bed trucks. Just keep in mind that it doesn't replace a sliding hitch as you may need one for a really short bed, especially if the trailer isn't tapered on the front nose for clearance.

What year, make, and model truck do you have, and does it currently have a gooseneck ball or factory prep package? I can help confirm the correct setup!

expert reply by: Andrew N

0

David

10/29/2026

Well that's a bummer. Guess I didn't research that well enough. Just purchased the Crosswing and it arrived yesterday. Also ordered the specific saftey chains too.... Trailer: 27 Keystone Cougar 30REP, comes with the Curt Helux pin box. Truck: 24 GMC 2500 HD AT-4 crew cab with the 6-3/4 bed. Concerns: -Weight -Cab clearance -Bed rail clearance (both above and inside from rear of pin box to bed cover rail)

Andrew N.

10/29/2026

@David Hey David, that's definitely frustrating, especially since you just received the CrossWing and already purchased the safety chains! You do have the option of keeping it and replacing the Helux with a standard rigid pin box, but I'd explore exchanging the hitch first. For your GMC's 6-3/4' bed, the Andersen # 3220 is a promising lightweight alternative at just 35 lbs. It works with the Helux using the required Lockout Kit # AN64ZR, although that restricts the pin box's shock-absorbing movement. Your Cougar's contoured front cap should help with cab clearance, and the Andersen offers up to 7-1/4" of combined offset. To verify turning clearance, measure from the center of your truck's gooseneck ball to the cab, then from the trailer's kingpin to the outermost front corner of its nose. The Andersen also adjusts up to approximately 19-9/16" high. Ideally, you'll want at least 6" between the trailer overhang and your bed rails when towing level. We'd also need to check how far the Helux extends behind the kingpin to make sure it won't contact your bed cover rails during sharp turns.

John

10/30/2026

I did not like the hitch nor the way it fastened I had to repair it twice the head came loose and I ultimately threw the crosswing out. It also caused twisting on my router Flex hitch which would have necessitated and aftermarket kit for the to address the flex issue on the PIN. I recommend one of the BMW full fifth wheel hitches and now that I've switched to it I don't have any checking and yes it is heavy but I feel safe. You get what you pay for

Andrew N.

10/30/2026

@John Hey John, sorry to hear about the issues you had! Were you using a lockout kit like # BLU62XR with your cushioned Rota-Flex pin box? The CrossWing isn't designed to work with an articulating pin box unless that movement is properly locked out, as it can cause unwanted stress on the hitch. Glad to hear the B&W is working better for you! It's definitely heavier, but it's a solid hitch.

Mark O.

10/30/2026

The crossing is a great setup. I use it to tow with. I don’t think you’ll regret it. I honestly don’t believe you’ll need the shock absorbing setup? But that’s a decision only you can make. I’d say try the crosswing first, if you can.

Mark O.

10/30/2026

Oh, I apologize. I just reread your question. I missed that your trailer already has the absorbing style pin box. On that note. As the tech responded. About the Anderson. You could try that route? I’ve seen too many of them crack or break.

Answer 1

Safety chains like the Curt #C95NR aren't required when using the Curt CrossWing Lightweight Gooseneck-to-5th-Wheel Trailer Hitch Adapter #C32DR but if you want to attach safety chains there isn't any harm in that either.

view full answer...

Answer 2

Tim, there is not a gooseneck ball height size recommended to use the Curt CrossWing Lightweight 5th Wheel Trailer Hitch #C92DR, so a 2 5/16" ball #BWGNXA2061 will work fine. Curt specifies that the only thing that needs to happen is that the…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Hey David! Unfortunately, the Curt CrossWing #C92DR isn't compatible with the Curt Helux Shock-Absorbing Pin Box because of the Helux's articulating design. Instead, I recommend the Andersen Ultimate 5th Wheel Connection #3220. It's…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 11

Hi Jeremy! For your Curt Helux Gooseneck Pin Box I recommend the Curt Tri-Ball Trailer Coupler Lock #C48CR. Curt specifically lists this lock as a fit for the Helux. It installs in the ball socket to prevent someone from hooking up to your trailer…

view full answer...

Answer 12

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Will Curt Crosswing C92DR Work With Curt Helux Shock Absorbing Pin Box?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching