The BrakeBuddy Towed Vehicle Battery Charge Kit part # BB54FR comes with a the Brake Buddy Select 3 Portable Supplemental Braking System part # HM39524. I have attached a wiring diagram of how this is setup with the Brake Buddy. view full answer...
The correct front and rear TorkLift Camper Tie-Downs for your 2019 Ram 3500 Crew Cab long bed with a factory hitch will be one of two options, depending on if you have running boards or steps under your Ram's cab or not.
If you do NOT have running boards or steps, the correct fit is the Front TorkLift Custom Frame-Mounted Camper Tie-Downs # TLD2140 and Rear TorkLift Custom Frame-Mounted Camper Tie-Downs # TLD3112.
If you DO have running boards or steps under the cab of your Ram,... view full answer...
That's a good question and the difference between the two SnapPad Jack Stand Pads for Motorhome are different shapes and depths, it isn't solely the notch in the center. I added photos of the two pads side-by-side so you can see the differences right next to each other. The correct pad will depend on the shape of your motorhome jack's feet:
- 10" Round Jack Feet: SnapPad Jack Stand Pads for Motorhome - 10" Round Jack Feet # SP64FR4
- 10" Octagon-Shaped or 10" Round Concave Jack Feet:... view full answer...
Measure the diameter of the feet of your Power Gear setup and we'll be able to determine if the # SP64FR4 is a fit. This part number is for 10 inch diameter feet which is most likely what you have.
If you had 9 inch diameter feet instead you'd want the # SP54FR4, 7 inch # SP24FR4 11-1/2 inch or 12 inch part # SP84FR74, 8 inch # SP34FR4 etc. I attached a page to see all the options we have since there are quite a few. view full answer...
The Reese Elite Series 5th wheel hitches, like part # RP30142, are designed to fit the Elite Series underbed rails that you mentioned installing on your 2016. Since it sounds like your 2020 GMC Sierra 2500 has the OEM pucks you will need to swap out your 5th wheel hitch entirely because the puck dimensions won't match up with the Reese Elite 5th wheel hitches.
The Demco Adapter Rails # DM6333 that you referenced will fit the pucks on the 2020 Sierra 2500 (whether you have a long or short... view full answer...
Thanks for the photos, and from that it looks to me like you are asking if just the pitch arm assembly is available, and if so, the answer is yes, it is the Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm # LC375994.
This is just the pitch arm part of the entire arm assembly, the Solera 69" Standard Flat Awning Support Arm # LC281154 so you do need to be sure this is the arm assembly you do have, and if so the pitch arm I referenced is the correct replacement.... view full answer...
The Ram Puck System is identical in the 6-1/2 foot bed and the 8 foot bed. If you already have a 5th wheel hitch with industry standard base rail compatibility, then I recommend the Demco 5th Wheel Rail Adapter # DM6099 or the Reese # RP30154. view full answer...
The Replacement Breakaway System for Brake Buddy Classic and Select Supplemental Braking Systems part # HM39340 replaces the brake away switch for the brake buddy Classic II, Select II, Classic 3 (# HM39494), and Select 3 (# HM39524). We have not yet installed the breakaway switch from this setup yet to have a video to for assistance but I have attached the installation instructions for installing the break-away with the Brake Buddy system. view full answer...
In order to get power from your motorhome to your 2005 Jeep while you're flat towing you'll need a working 7 way with 12 volts. Since the front of your Jeep has a 4 way flat on it you will need to change out the plug because all 4 wires are being used. The tail light circuit won't have enough power to charge the battery and run the lights on your Jeep, however you won't be forced to rewire everything, just the plug on the front of the Jeep.
If you don't have 12V at the back of the 7... view full answer...
Most R-Pods are going to have a torsion axle, and since yours is a 3,500 lb axle from Lippert that means you will have either a diamond torsion axle or a square torsion axle. To determine which axle you have - and thus which lift kit you need - take a look at the accompanying photo a customer sent in. This was from installing a lift kit on a diamond torsion axle, which will be oriented under the trailer in the shape of a diamond, as per the name of the axle. Otherwise the axle will be oriented... view full answer...
The Demco rail adapter kit that you need for your 2020 GMC Sierra 3500 HD is part # DM6333 which is different than the part # DM6194 which was referenced for the 2019 model year. The adapter # DM6333 has a 21K weight capacity and it is compatible with your puck system whether you have the long or short bed. view full answer...
To connect your Blue Ox tow bar, such as their Alpha # BX7380, to your Wrangler Unlimited's towing bumper's 1-inch D-rings you will want adapter kit # BX88296. This includes the 7/8-inch pins and retaining clips. You can see how this installs in the linked photo. view full answer...
I was able to confirm through my contact at Retrax that the T-channels on your 2019 Ford Raptor OEM tonneau Cover, model number VJL3Z84501A42A, share the same dimensions as the T-channels on the RetraxPRO XR Hard Tonneau Cover w/ Trax Rails # RTT-80373, confirmed to fit the same truck. This is true because Retrax helps to manufacture some of the components for the Ford tonneau covers.
With that in mind, the correct Rhino-Rack Vortex Crossbar System for your F-150 is # RRVA180B-RRRLT600,... view full answer...
In order to replace just the factory anti-sway bar bushings on a Ford F-53 Chassis you have a few options which will be based on the location of the anti-sway bar (front/rear) and the gross vehicle weight rating of the coach (15,700 lbs, 16,000 lbs etc.) or diameter of the factory sway bar (1-1/2", 1-3/8", or 1-5/8"). If you need bushings for a front anti-sway bar and it is 1-5/8" diameter then you can use the Roadmaster Polyurethane Bushing Kit part # RM-4139-127 but if you need bushings... view full answer...
There are SolidStep Lift Assist Kits that can be used to upgrade certain SolidSteps.
- SolidStep Lift Assist Kit for 26" to 29" Wide RV Door Frames # LC733937
- SolidStep Lift Assist Kit for 30" to 36" Wide RV Door Frames # LC733939
These kits will only work with the triple and quad SolidStep 3.0. I have added photos from the instructions of these lift assist kits, which includes instructions on how to tell the correct kit if you have a SolidStep 3.0 already installed on your trailer. view full answer...
I believe you are asking if the Go Power Overlander Expansion Kit - 190 Watt Solar Panel # 34282182 will work with the Go Power PWM Solar Charge Controller # 34276119, which is a 30 amp controller, and the answer to that is yes it will. It comes with everything needed to add the panel to your system.
Overall, this is compatible with a number of Go Power solar charging systems:
- Go Power Solar Elite Charging System - 380 Watt Solar Panels - 2,000 Watt Inverter Charger # 34282184
-... view full answer...
The Replacement LED Light Strip for Solera RV Awning LED Fabric Light Kits # LC423331 is the replacement for the strip mounted in a track, which is the LED Fabric Light Kit # LC674282 (15 feet) or # LC674283 (21 feet).
Technically yes, the Optronics Flexible LED Light Strip # UCL91CB (16 feet) will work, as it wires the same with power and ground, but there is no guarantee it will fit the track of the Solera kit, as it is a slightly different width. Because of that my recommendation... view full answer...
Great question!
From what I could find in the owner's manual for a 2015 Fiat 500 (looking both at the Recreational/Flat Towing and Emergency Towing procedures) it does look like you need to keep the steering wheel unlocked while flat towing. Since this means your ignition is on, it can very well drain your battery. I'm not sure why this isn't something that is commonly known because even some of our flat towing manufacturers don't have this info on their site. I reached out to Roadmaster... view full answer...
The Ground Control jacks for travel trailers are different as they are a C-jack instead of a vertical lift. I recommend using the Replacement C-Jack for Lippert Components Electric Ground Control TT # LC404488 for that application instead of combining because the system is different using a completely different controller as well.
The Replacement Right Rear Leg for Lippert Ground Control 3.0 Electric 6 Point Leveling System # LC428493 and the Replacement Left Rear Leg for Lippert Ground... view full answer...
Since your plan is to install a brake controller and want to charge the camper battery what you need is actually the part # ETBC7. This comes with basically the same things as the # ETBC7L except it also includes wiring and circuit breaker to complete the brake controller circuit that you use for charging the trailer battery.
I attached a video that shows this kit installed on a similar 2011 Subaru Outback for you to check out as well. The brake controller in the video is our best selling... view full answer...
The correct Replacement Operator Mechanism for your model 4751KS MaxxAir MaxxFan is part # MA10-20281K-1AF. If your fan lid is unable to open even manually, then this is the part you need to replace.
The other part you referenced, # MA10A04751KS would replace the printed circuit board on your MaxxFan instead.
If you aren't sure which part needs to be replaced on your MaxxFan, let me know what issues you're having with it and I'll be happy to point you in the right direction.
view full answer...
The Replacement LED Light Strip for Solera RV Awning part # LC423331 is .394" wide so you will need to have this much space inside the channel for it to mount but I suspect it would indeed work. If you wanted to be certain however you could just obtain the LED Fabric Light Kit part # LC674283 which comes with the channel as well as the light strip. The above two options are both cut to fit. view full answer...
I reached out to Furrion who told me the Trim Kit for Furrion Built-In Microwave - Black # FMSM09BLTK and the Trim Kit - Stainless Steel # FMSM09SSTK were made of plastic and that when installed on a microwave the trim kit will be 23-1/2" x 15".
These are designed to fit around the Furrion Built-In Microwave - Black # FMSN09BL or Furrion Built-In Microwave - Mirror Glass # FMSN09MG. I have added a side-by-side photo of the microwave without the trim kit installed and with it installed... view full answer...
The access hole cover, part # 306-XA2002, isn't needed for all of the 2019 Tesla Model 3 so look under your car before getting it. Some of the 2019 models have a cover installed right from the factory. view full answer...
The physical difference is that the # LC386322 has a connector on it and the part # LC387738 has two blunt cut wires that would need to be spliced. They are the same thing aside from that. One is just intended for the Lippert brand and the other Power Gear but both are made by same parent company Lippert. view full answer...
I suggest using the 7-Way RV Upgrade Kit part # ETBC7L and the Curt Echo part # C51180 because of the ease of installation and convenience. The Curt Echo Mobile Trailer Brake Controller just needs the basic trailer lighting functions and 12V power to be fully operational. Just wire the 12V black wire from ETBC7L to the vehicle's battery via the circuit breaker, ground the white wire and connect the 4 pin to the 4 pin portion of the plug shown in the picture I attached. The rest of the wires... view full answer...
The Replacement Cover for Solera Awnings part # LC643923 is for the idler head side. If you need the drive head side then the matching one for this is the Replacement Cover for Solera Awnings part # LC643922. view full answer...
The Malone TopTier Load Bar Kit for Utility Trailers part # MPG493 fits 4' wide and 5' wide trailer decks so it would not be compatible with your 6 foot wide utility trailer.
The Malone Crossbar Conversion Kit for Standard Utility Trailer part # MPG475 will fit the 6'x8' utility trailer if it has an open frame with square rails.
view full answer...
The correct size crossbar to use on the bed of your 2018 Ford F-150 with the PowertraxONE XR Hard Tonneau Cover w/ Trax Rails part # RTT-70373 is 71" which means the Rhino-Rack Vortex Crossbar System for Retrax XR Series Tonneau Covers part # RRVA180B-RRRLT600 is what you will need to use. The 65" long crossbar in the Rhino-Rack Vortex Crossbar System for Retrax XR Series Tonneau Covers part # RRVA165B-RRRLT600 is designed for mid-size trucks like a Tacoma, Ranger, or Colorado.
If you... view full answer...
Yes, the Replacement 7" Monitor for Furrion Vision S Wireless RV Camera System # FR47FR is 100% compatible with your existing Furrion Vision S Wireless RV Backup Camera System # FOS05TASF and will make for a very nice upgrade.
Both the 5" and 7" monitors use the same power cord # C-FOS07TAPK-006 and suction cup mount # FR79SR, so you will still be able to use the ones you currently have. view full answer...
Curt has a fifth wheel bracket kit that fits your 2020 Chevy Silverado 2500HD without OEM rail kit with the part # C16429 or for a kit with rails part # C16429-204. view full answer...
I spoke with my contact at Blue Ox regarding your Aventa LX 7445 Tow Bar and the Short Hitch Connector Assembly # BX84-0051 that you mentioned. She stated that this assembly is technically compatible and will work with your tow bar, but it will reduce its capacity to 6,500 pounds.
Since your Blue Ox Aventa LX 7445 is rated at 10,000 pounds, a better option is with the Standard 2" Hitch Connector Assembly # 84-0186. My contact confirmed that this will work as a replacement shank for... view full answer...
B&W indicated that you can use either 10" or 12" lube plate with the B&W Companion. The 10" is the most common size like part # RP83002 however the skid plate of the B&W hitch is wide enough to accommodate 12" lube plate part # RP83001 so you won't have an issue. view full answer...
The dimensions of the Undercover Access Hole Cover for EcoHitch Stealth Trailer Hitch Receiver # 306-XA2002 that you referenced is 8-1/2" long by 5-1/16" wide by 1/8" thick. Your hole being initially cut with a 4 inch hole saw would not be too large to work with this. view full answer...
Since your 2019 Open Range 374BHS has the Lippert 6 point Ground Control system and the foot plate is pinned in place the part # LC344792 that you referenced is the correct leg. The part # LC428493 is for if the foot is welded to the jack leg. view full answer...
All of the 2017 Ram 2500 models have the structure built already under the bed to add a gooseneck hitch. Models with the factory prep package would actually have the hitch and the four 5th wheel hitch holes in the bed.
If it were me I would go with the B&W option, # BWGNRK1384, since they are so well made and made right here in the USA. Because Ram had that structure as a part of the vehicle build it makes it a lot easier to add a gooseneck hitch. You can use # 9467 from Draw-Tite,... view full answer...
The brake controller port for your 2019 Ram 3500 is a bit of an odd location relative to where the port is on other trucks; the port is underneath the control knobs like in the accompanying photo. You will be able to find the plug behind that panel, which has clips you can remove.
Doing this will allow you to plug in the Redarc Plug-and-Play Wiring Harness for Tow-Pro Trailer Brake Controllers # 331-TPH-020 so you can use the Redarc Tow-Pro Elite Trailer Brake Controller # 331-EBRH-ACCV2.... view full answer...
Yes we do. The correct rear cover you need is the part # LC289567 to match the front cover # LC643923 you referenced and the picture you sent in. view full answer...
The HappiJac Qwik-Load Upgrade Kit for Standard Turnbuckles part # LC182894 is an excellent upgrade option for the HappiJac Original Turnbuckles for Camper Tie-Downs part # LC182898. These are going to cut down dramatically on the time it takes to secure the tie-downs. In regards to installation, you can either cut the hooks off your existing tie-downs or you can just go pick up some 1/2" all-thread at a home improvement store which is very cost effective and readily available.
Unfortunately,... view full answer...
Thank you for the pictures. You are definitely correct that you need the Demco Hijacker Autoslide Locking Plate for MOR/ryde Pin Boxes # DM6025 to use the MOR/Ryde pin box with your Demco Hijacker # DM8550024.
The pictures that you sent in looks like your dealer just welded on some brackets of their own to lockout the Hijacker. If you notice the picture that I have attached the bracket from the Demco locking plate looks nothing like what they installed which is why you aren't seeing... view full answer...
You can certainly do that. You'll want to be sure to wire the pin on the vehicle side to correspond with the 12-v power supply pin on the 6-way motorhome trailer connector however. Some 6-ways use the center pin as the brake controller output, some use it as the 12-volt power feed, so you'll want to ensure both sides are wired the same way. Roadmaster offers a purpose-built circuit protected kit for this, part # RM-156-25.
Keep in mind that the circuit is capable of providing a maintenance... view full answer...
The 2020 GM factory rail kits were changed from 2019 so the correct adapter you'd need is the part # DM6333 and not the Curt # C16023 that you referenced as it fits the first generation of GM rail kits. view full answer...
Congratulations on your new truck!
To use a Demco Hijacker Autoslide 5th wheel hitch with the factory puck system on your 2020 GMC Sierra 3500 you will need the Adapter Rail Kit # DM6333 and then you can use either the 18K # DM8550034 or the 21K # DM8550035 Hijacker. Since there aren't any custom mounting kits for your puck system the adapter rail kit is what you need to use. view full answer...
The best fifth wheel hitch for your 2019 Nissan Titan XD short bed with the factory gooseneck is the Demco Hijacker Autoslide because you will never again need to get out of your truck just to make a turn, making your towing experience much more convenient. It also has a highly secure jaw system which ensures a complete, secure connection to your trailer's king pin as well as its cushioned head which will give you a smoother and quieter ride while towing.
The Hijacker will mount onto... view full answer...
The proper location to install the front rail on the Curt 5th Wheel Installation Kit # C16424-204, for your 2016 Ford F-250 is 54-3/16 inches from the rear edge of truck box (to the rear edge of the front rail). This applies to both short and long bed trucks.
On the other hand, the front rail on the Curt 5th Wheel Installation Kit # C16448-104, for the 2013 Ford F-150 installs 50.938 inches, again measured from the rear edge of the truck box to the rear edge of the front rail, regardless... view full answer...
The Demco 5th Wheel Rail Adapter part # DM6175 weighs approximately 99 lbs. This adapter will fit into the factory puck system on Ford F-250 and F-350 trucks from 2011 - 2018. It will then allow for 5th wheel hitches that have above bed industry standard rails (ISR) to be used with the factory puck system. For a lightweight alternative that has the same function as the above adapter, I recommend using the Reese 5th Wheel Rail Adapter part # RP30156 which weighs in at around 55 lbs and is... view full answer...
The Firestone Air Command II Compressor System w F3 Wireless Remote, Xtreme Duty Compressor, Tank, Hose # F2592 will automatically fill the tank so there's no need to run one of the paths to the tank. The dual path can be used to level your air bags from side to side individually or can be used for a set in the front and a set in the back.
The compressor fills the tank, and then with the wireless remote you can fill the bags from the tank or use the hose to fill any other items. Since... view full answer...
I attached a picture that shows how the Timbren # TGMRTT35D that you referenced gets assembled. The spacer # TA25722-90P00 you referenced would go between the numbers 2 and 3 and you'd be set. See attached picture. You will need to provide a longer bolt though so that it can all fit together. The same portion of the Timbren fits into the bump stop cup on your 2019 Chevy Silverado 2500HD. view full answer...
The # LC359281 is for the 17K capacity Kwikee Atlas Level Best jack. It only provides the cylinder itself. For the entire assembly, use # LC359275. view full answer...
We have replacement pitch arms for the Solera 69 inch awning setups like what you have with the part # LC375994 which would be all that you'd need. view full answer...
There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer.
A junction box/7-way plug kit like Epicord # 277-000141 or # e99011 is another option you have to convert the camper to match the 7-way RV blade type connector format. This avoids the extra connection points and potential trouble spots from using separate adapters. These items use different wire colors so be sure to follow the wiring guide for the specific... view full answer...
For a no-drill application, you'd first want to install the # e99034 Raised Side Rails. (The # e99033 you'd looked at is for an earlier Odyssey, and wouldn't fit your 2020 model). With the side rails in place, I'd recommend going with the Malone AirFlow2, part # MPG216 to provide crossbars. You can see current pricing by using the provide links.
I've also linked to install and demonstration videos.
view full answer...
Yes, I do have an option for you to carry bikes with your flat-tow setup. However, since there is not a trailer hitch for your vehicle yet and you don't want to use a trunk mount or roof rack bike rack then you will have no other option but to use a dual hitch adapter and place the bikes on a hitch mounted back rack between the tow vehicle and toad. For this, we have a few options for you depending on your rise/drop needs.
In order to determine what your rise/drop needs are we will... view full answer...
The way the Lippert Entry Assist Handrail for SolidStep Manual RV Steps part # LC799640 installs and where it mounts will not fit on a 2 step Solid step like part # LC713662. There is no where for the bottom piece of the hand rail to install. I have attached a photo for your reference. For this reason I cannot recommend modifying the rail.
I recommend to use a Stromberg Carlson Folding Handrail for Fleet RVs part # AC-544 which installs on the side of the RV and folds up against the... view full answer...
Lippert made two types of 3.5K torsion axles, the Square and the Diamond. The difference between the two is the orientation of the axle beam, as shown in the photo I put together for you.
Given the orientation of the axle beam shown in your photo (thanks for the photo, by the way!), I was able to determine you have a Lippert Square axle, which would use the Lippert # LC382741 Square Torsion Axle Lift Kit. The kit will provide 3-1/2 inches of lift. For a tandem axle camper like your Trail... view full answer...
I have attached for you below an exploded parts breakdown of the Titan/Dico Model 10 Surge Brake Actuator. In regards to the Replacement Top/Bottom Bearing part # T1020900 and Replacement Side Bearing part # T1242700, these work to help stabilize the inner slide inside the outer case and would have been installed on all models. There should be a total of six for the top/bottom and eight for the sides. In regards to the Replacement Rear Roller part # T0829100, these sandwich the upper Replacement... view full answer...
I have a solution for you, but we do not offer a fully electric option hot water heater for RVs. If you have an Atwood, Suburban, American, or Moreflow hot water heater, you can use the Hott Rod RV Water Heater Conversion Kit # DGR6VP (6 gallon heater) or # DGR10VP (10 gallon heater). This kit will safely convert your propane water heater to electrical use while keeping your low pressure propane system in tact. The heater cord requires a 110v outlet, so if your RV electrical system does... view full answer...
The reason the assembly looks pretty new is because based on the motor 1101422 / 214-1001 you mentioned, your motorhome's steps were upgraded.
The only catch is you have to know when this upgrade occurred, which I realize is problematic for a used motorhome. But if this update occurred in 2005 or before you need a new step assembly. If it happened after 2005 we have exactly what you need with the Replacement Motor for Kwikee Electric RV Steps # LC379147 and Replacement Gear Box and... view full answer...
The Lippert 15-Foot LED Fabric Light Kit for Solera RV Awnings # LC674282 is intended to install by sliding into the light cord by the coach sidewall, under the awning, that is sewn into the awning fabric.
If you prefer an LED light strip that installs with an adhesive backing we offer 17-foot Optronics LED Light Strip # UCL90CB. This waterproof light strip has 3M peel-and-stick adhesive backing and a total of 300 diodes. Multiple light strips # UCL90CB can be joined together simply... view full answer...
The 7-Way RV Upgrade Kit for Trailer Brake Controller Installation part # ETBC7L and the Universal Installation Kit for Trailer Brake Controller part # ETBC7 will both still charge your trailer's battery even when using the Curt Echo Mobile Trailer Brake Controller part # C51180. The onlybdifference between these two kits is that the latter comes with extra wires and circuit breakers which are needed for a in-cab brake controller but you could still use this with the Curt Echo as well if... view full answer...
There is not an adapter for the 15K Hitchhiker 5th wheel hitch you have with rails running front to back. The only adapter currently available is the Demco 5th Wheel Rail Adapter for 8 foot bed # DM6206 of the 6-1/2 foot bed adapter # DM6194. Both of these are rated for up to 21,000 lbs and will give you the industry standard rail locations for the hitches compatible with the horizontal bed rails.
My recommendation is to use the Curt A16 # C16520-16025 for a long bed truck or short... view full answer...
There are two different 7-way trailer wiring harnesses for a 2019 Subaru Ascent dependent on whether or not you have the factory tow package. If you do have the factory tow package then you should be using the Tekonsha OEM Replacement Vehicle Wiring Harness part # 118290, not the Universal Installation Kit for Trailer Brake Controller part # ETBC7. If you found a plug under the dash for the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 3062-P then you have the factory... view full answer...
The Curt # C16024 fifth wheel legs you mentioned fit the A series hitches from 20k and up; the A20 # C16540, A25 # C16580, and A30 # C16590. They're technically designed for the A30 because of the legs's 30,000 pound rating but they still fit the other two. With that in mind they will not, however, increase the weight capacity of the other 2 hitches.
The # CU53FR legs fit all of the same hitches plus the Q Series and E Series hitches as well. These legs even fit the A30 however they... view full answer...
To upgrade your A&E awning you can either use the 12V Solera Conversion Kit, White # LC434724 or Black # LC434723, OR the 18V Solera Conversion Kit, White # LC434730 or Black # LC434729.
Both options use electricity to extend and retract the awning, but they also include manual overrides so that you can do it by hand in the event of a power failure.
The 12V kits connect directly to the 12V power of your RV while the 18V version uses it's own (rechargeable) battery so it's a little... view full answer...
For your 20K Pro Series 5th Wheel hitch to work with the factory puck system on your 2019 Ford F-350 you will need an adapter. There are currently two options to choose from and I recommend the Reese Elite Series Underbed Rail Adapter for Standard 5th Wheel Trailer Hitches - 20,000 lbs # RP30156 which will work well with your hitch as they are the same brand and capacity, but you can alternatively use the Demco 5th Wheel Rail Adapter for Ford OEM 5th Wheel Towing Prep Package - 25,000... view full answer...
I spoke with my contact at Lippert regarding the 366043 model motor/gear box assembly for your Kwikee Steps. He stated that the correct replacement motor is the Lippert Kwikee Motor # LC379147 and for the gear box you will use # LC379160. These will be exact replacements on your step assembly.
Pricing information for both parts will be listed on the product pages.
view full answer...
I do have an option for you but I don't really see a way for you to use the Thule HideAway Awning part # TH490008 with the Prime Design Roof Rack AR-2100-AR2108 on your 2018 Ford Transit T150 due to the side rails being in the way. If you were to somehow remove the side rails then the Roof Rack Adapters for Thule HideAway Awnings part # TH490001 would most likely be able to mount to the crossbars but not with the side rails in place.
If you can't remove the side rails on the Prime Design... view full answer...
I attached a picture I took from the install instructions of the Toolbox Mounting Kit for Thule TracRac SR # TH25200 that you referenced that shows how it installs relative to a TracRac SR ladder rack.
If you wanted to add a cantilever extension to the rear bar of the TracRac Sliding Ladder Rack # TH43003XT-501EX all you'd need is the # TH43002XT-508EX. Feet of the uprights would interfere with allowing a third bar to fit in the middle though. view full answer...
Correct, the puck spacing on Chevy Silverados and GMC Sierras changed for the 2020 model year which means the B&W Companion OEM 5th Wheel Hitch for a 2016-2019 model year will not fit. However, in order to avoid having to replace the entire hitch you can replace just the base portion and reuse the head. There are three bases available which I have attached for you below:
Fixed 20K Base - part # BWRVB3710
Fixed 25K Base - part # BWRVB3715
Slider 20K Base - part # BWRVB3775 view full answer...
I do have a custom 5th wheel install kit available for your fifth generation 2019 Ram 1500 but the Reese Quick-Install Custom Bracket Kit for 5th Wheel Trailer Hitches part # RP50142 is not a confirmed fit. Instead, you will need to use the Demco Above-Bed Base Rails and Custom Installation Kit part # DM8552032-71 which is currently one of the only available options for you so long as you don't have the factory airbags.
Please note that you do not need to use a Reese install kit in order... view full answer...
The direct replacement for your Ventline screen with model number VD0434 is # BVD0434-31 (birch white) or # BVD0434-41 (polar white). This is compatible with Ventline Ventadome roof vent models V2092, V2110, V2094 and V2119.
However, if you're referring to the plastic tabs pointed in the photo I attached, then what you need to replace is the complete frame assembly with part # BVC0573-31 for birch white, or # BVC0573-41 for polar white. This includes a new screen as well. The standard... view full answer...
Draw-Tite trailer hitches # 76046 and # 76046-SK are essentially the same hitch except # 76046-SK includes a bracket kit that's for relocating the carbon canister on the hybrid model of the 2019 Chrysler Pacifica. The relocation kit by itself is part # 76046SK. I've attached a picture of the extra brackets.
We haven't heard anything specifically about the hands-free lift gate not working after the hitch is installed. Looking at the location it doesn't appear that it would except right... view full answer...
Good question, and the difference between the standard Solera 12V Power RV Awning Conversion Kit # LC434724 (White) or # LC434723 (Black) and the Solera Smart Arm 12V Power RV Awning Conversion Kit # LC759405 (White) or # LC759517 (Black) is the latter's touchpad (pictured).
This touchpad allows you to control the awning along with the included switch, and it also allows you to use additional accessories, the Solera Smart Arm Wind Sensor Kit # LC715123, Solera Smart Arm Infrared Security... view full answer...
I have attached for you a set of photos which are used to identify the landing gear legs on a trailer. I assume you have either the older Lippert Ground Control 2.0 Leveling System or the newer Lippert Ground Control 3.0 Leveling System. If that is the case then the easiest way to tell which is which is to note the shape of the rear jacks. If the jacks are square then you have the Lippert Ground Control 2.0 Leveling System therefore need the Replacement Heavy-Duty Landing Gear Jack Leg... view full answer...
I do have an option for you but the Lippert Handrail for Victory Step Manual Fold-Down Steps part # LC726866 is designed for the Victory Step fold-down steps. From your photo, it looks like you have a Lippert Solid Step like part # LC698799 and there is not a handrail available that mounts directly to the solid step. However, you can use the Lend-a-Hand Extra Large Folding Grab Handle for RVs - Black with Black Foam Grip part # AM-533 which is going to attach the door frame stud and give... view full answer...
I can't say that we've heard of any issues with needing special wiring for your 2020 Toyota Highlander, especially if it already has the 4 way plug like the # TK74FR installed from the factory-all of the wiring has already been done. The only thing I could think that they're referring to adding would be a brake controller adapter plug, which would require significant wiring work to be done inside the vehicle; regardless, I have a solution for you. Since that 4 way is already present, you... view full answer...
I spoke with my contact at Lippert regarding your existing motor/gearbox model 5973820. He stated that the correct replacement motor is the Lippert Components Kwikee Step Motor Replacement Kit # LC379608. This is a direct replacement for the motor that originally came with your assembly and will work perfectly with the existing control unit. For the gearbox you'd then want the part # LC379160 that you mentioned as well. view full answer...
It's definitely a good idea to transport your Biria Electric Folding bikes on a bike rack and we do have a couple of really good options which will allow you to carry two of these bikes, which from my research are 55 lbs and like you said, do have tires which are 4 inches wide. Since these bikes have fenders you will need a frame-mounted bike rack and there are two options to choose from.
The best bike rack for your Biria Electric Folding bikes is the Thule EasyFold XT # TH903202 because... view full answer...
I took a look at your order and saw you had purchased the Replacement Key Wall Control part # MA00A03550K but the issue you are having with your MaxxFan Model 4751KS is the circuit board, the Replacement Circuit Board part # MA10A04751KS so this what you need to replace. view full answer...
The wireless remote that comes with the Brake Buddy Select 3 # HM39524 is designed to sit in the cab of your RV and still be able to communicate with the portable system that is mounted in your towed vehicle. You won't need a signal booster to use this system. view full answer...
For your 2017 Jeep Wrangler with a Smittybuilt XRC bumper we have the Blue Ox adapter part # BX88357 which will allow to connect the vehicle to a Blue Ox tow bar like part # BX7380.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install... view full answer...
I have an option for you, but the Air Lift WirelessONE Compressor System # AL25980 is not designed to be used with an onboard air tank.
It sounds like what you're trying to do is basically add a wireless remote to your existing set-up, if that's the case, the most cost effective solution available is the Air Command F3 Compressor System with Wireless Remote # F2590. You can connect the ECU (electronic control unit) to your existing onboard air tank through a regulator which will allow... view full answer...
The Curt Auxiliary LED Indicator Lights # C53201 being an LED kit has very little power draw so even a slight connection issue can drastically impact function. I recommend cleaning each connection with sand paper and then using dielectric grease # 11755 to make sure the connections keep moisture and corrosion out.
if that doesn't solve the issue with function, then next step for LED lights is to add load resistors like # DI34ZR for the functions. This will create a draw like a light... view full answer...
You can absolutely use the Furrion Vision S Side Camera w/ Marker Light Bracket - 2 Cameras # FCE48TASL with the LED lights on your Forest River trailer. The camera only uses 0.25 amps when the infrared is off (at daytime) and 0.5 amps when the infrared is on (at night) which is very little so you won't have any issues. I have added a link to a video review of this system for you to check out.
As a note, the Vision S side camera system is designed to be used with the Furrion RV Observation... view full answer...
Yes, you can upgrade the 4.3 inch monitor of your Furrion setup to the 7 inch # FR47FR or the # FR97FR for the 5 inch. This will work great and give you an easy to view monitor. view full answer...
The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads.
So to determine the correct brake pads, all you need to do is match up whatever your calipers are rated for to the pad you need:
- Calipers rated for 3,500 lbs - 6,000 lbs: Kodiak Ceramic Brake Pads # K225CP
- Calipers rated for 7,000 lbs - 8,000 lbs: Kodiak Ceramic Brake Pads # K250CP
- Calipers rated for 9,000 lbs - 10,000... view full answer...
I have a solution for you since the Progressive Dynamics # PD4045KA is not compatible with lithium batteries right out of the box. If you've already got the # PD4045KA as your power distribution panel, you will simply need to swap the converter in the unit with the Replacement Lithium Converter for Progressive Dynamics 4000 Series RV Power Control Center - 45 Amp # PD4045LICSV. This will allow you to use a lithium battery setup in your truck bed camper and have the proper charging and power... view full answer...
I have a solution for you, but I talked to my contact over at Air Lift about this and it really is not a cost effective solution because it would involve purchasing an additional tank and air compressor system to replace the system that is included, as well as wiring in solenoids, low pressure switches and re-wiring the system. The AirLift # AL25491 is a great system because it provides individualized inflation to each air bag in the system, but you would spend considerably more in parts... view full answer...
The Lippert Replacement Reverse Polarity Solenoid for RV Hydraulic Slide-Outs part # LC136046 and part # LC118246 are the same solenoid but vary in how they mount. The part # LC136046 mounts using a strap around the motor like what you have therefore this is the correct replacement for you whereas the part # LC118246 mounts on a tray beside the motor.
view full answer...
It sounds like you're trying to replace the motor on your Kwikee steps with the part number 366043, and we have just what you're looking for.
In order to replace the motor for these steps you'll want to use the Replacement Motor for Kwikee Electric RV Steps - 12V # LC379147. If you also need the gear box replaced you'll want to use the Replacement Gear Box and A Linkage # LC379160. These are the correct replacement parts, per Lippert, for your Kwikee model 366043 steps. view full answer...
To install the replacement clamp assembly # 8880737 and bracket # 8880736 on the Yakima SlimShady Awning # Y07409, there are two t-bolts that are inserted into the upper channel of each side of the SlimShady rail. You would then place the clamp onto the bolts and thread a lock washer and nut on each bolt. At first you only need to tighten by hand and once installed, open the clamp completely.
This allows you to slide the clamps along the awning to properly position them for installation.... view full answer...
If the 2018 Jeep JL Wrangler has a factory tow package you can just use a Tekonsha Brake Controller p3 part # 90195 with a brake controller harness part # 3073-P to install a brake controller in the Jeep. The harness will plug into a port under the dash and you will not need to worry about hard wiring to the cold side of the brake switch.
If your 2018 Jeep JL Wrangler did not come with a factory tow package, you can install a brake controller two different ways. The easiest way is to... view full answer...
While I can certainly understand wanting to add an extension for your clearance issues, a hitch extender cannot be used with a weight distribution system, though there is an option that can help, which is a longer shank for your weight distribution system.
The longest shank for your Ram's 2" hitch is from Equal-i-zer and is 18" long.
- Equal-i-zer Weight Dist Shank - 18" Long - 7" Rise, 3" Drop # EQ90-02-4500
- Equal-i-zer Weight Dist Shank - 18" Long - 8" Rise, 4" Drop # EQ90-02-4600
I... view full answer...
The Curt Q25 5th Wheel Hitch # C16265 will work with an adapter for the puck systems. You simply need to recognize that some adapters will limit the towing capacity. Curt is one of the hitches that uses legs compatible with the different pucks, so I will give you both options.
For a Ram, you will use Reese adapter # RP30154 or Demco # DM6099. You can alternatively use the Curt legs # C16021 which will mount directly to your pucks.
For a Chevy or GMC, you will use the Curt OEM 5th... view full answer...
I confirmed with my contact at Lippert that motor kit # LC379608 and linkage kit # LC379648 are indeed the correct replacement parts for your older Kwikee Series 28 electric coach step. My contact indicated you do NOT also need linkage kit # LC379161.
We do also have an update kit for this older step, part # LC379769, which includes the latest design integrated motor/gearbox/linkage. This brings your step more in line with their current production models.
Another option that might... view full answer...
The Replacement Converter Section for Progressive Dynamics 4000 Series RV Power Control Center part # PD4045CSV is a direct replacement for the converter section on the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger part # PD4045KA. It is an exact replacement as it will do exactly what the original converter did. view full answer...
The only parts list for your triple step is attached. It unfortunately does not give the breakdown to the extent you are seeking with Teflon plate and wave washer as those parts are not replacement options from the manufacturer. I've attached the best parts list from the manufacturer I can get as an attempt to help. If your parts are worn then I recommend getting the replacement kit # LC379804 because not all the parts you are seeking are replacement options. view full answer...