Replacement Bearings For Dexter Axle On A 1999 Jayco Pop-Up Camper

Question

Question:

Im trying to find out what wheel bearings I need for my pop up camper. Its a 2500# dexter torsion bar axle from 1999. 0150159 is stenciled on the axle. Information on the label says Jayco 206916-1. SN-D3232472

asked by: Michael M

0

Expert Reply:

I reached out to my contact at Dexter and was able to get the wheel bearing numbers you need for your 1999 Jayco Pop-Up Camper. The inner bearing is # L68149 and the outer bearing is # L44649. I recommend getting the complete kit which is Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal # BK2-100. This kit will include the inner bearing and race, the outer bearing and race, the grease seal, the cotter pin, and tang washer for EZ-Lube applications. I've attached an installation video for you.

I recommend getting the Replacement Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2, # RG04-040. I also recommend using LubriMatic LMX Industrial Strength Grease - 14 oz. Cartridge # L11390, and using the Plastic Bearing Packer # PTW1218.

expert reply by: Jason S

0

Jeffery

5/11/2024

I need the axle for the exact Jayce pop up any idea length and diameter

Reply

Jameson C.

5/23/2024

@Jeffery We don't have a way to look that up but it should be on the axle tag on the trailer. Keep in mind we don't offer torsion axles.

Reply

Answer 1

Thank you for providing that information. Leaf springs like the ones you have now typically match the axle capacity on your trailer. Although adding leaf springs with a slightly higher capacity won't hurt, it also is not necessary. Based on the…

view full answer...

Answer 2

Hey Brian, thanks for reaching out! The measurements you have are similar to the 4-Leaf Double-Eye Spring for 4,400-lb Trailer Axles #DX95CR so it sounds like your leaf springs aren't flattening out as of yet. If you drive on some pretty rough…

view full answer...

Answer 3

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 4

Hey Kevin thanks for your question. There is not much downside to going with the 5,000 lb springs instead of the 3,500 lb. A higher rated spring may make the ride a bit more "chunky" at times, since the spring would not flex as easily.…

view full answer...

Answer 5

It's okay to replace leaf springs with ones rated for more weight and pretty common to do so but keep in mind, the higher you go the rougher the ride will be. If you have a utility trailer then I'd probably opt for the higher rated 5,000 lb…

view full answer...

Answer 6

If you can get me the axle capacity and the wheel bolt pattern of your trailer I can help you pick out the correct spindle and hub for it.

view full answer...

Answer 7

One of the biggest differences between the 6-leaf 5,000 lb trailer axle leaf spring part #UG34FR and the 4-leaf part #e44SR is the length. The 6-leaf setup is 30 inches long and the 4-leaf setup is 25-1/4 inches long. In general though the number of…

view full answer...

Answer 8

A Dexter Torflex axle that has a capacity of 1,400 lbs would be a #9 Torflex axle, and we do have the right bearing kit for that. The correct part is the Bearing Kit #BK1-150.

view full answer...

Answer 9

Yes the Bearing Buddy part #BB1980A-SS is correct for the Dexter hub you have #8-247-50UC3 and then for the bearing kit part #BK2-100 is also correct! You made my job easy.

view full answer...

Answer 10

The Wesbar light #271594 hangs on studs so it would not work in place of the lights on your Jayco trailer but I do have another recommendation. Take a look at light #RVSTL61 for the left and #RVSTL60 for the right. These lights have mounting holes…

view full answer...

Answer 11

SAE numbers aren't normally good for picking out replacement trailer light components since they aren't part numbers but in your case we have seen the number SAE-A116PCPC2RSS2TT2-97-DOT enough times to know that the correct replacement lens…

view full answer...

Answer 12

It is possible that the Bargman Tail Light, #30-92-003, will work on your 1999 Jayco Eagle 12, but that will depend on the type of tail lights it currently has. Some of them also used a wrap-around style lights. The best way to find replacement…

view full answer...

Replacement Bearings For Dexter Axle On A 1999 Jayco Pop-Up Camper

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching