Hello Robert, Thank you so much for attaching the pictures, they’re always so helpful. In the first photo, it looks like your shackle straps are sitting a bit too vertically. That’s not a major issue, but since you’ll be replacing some suspension…
Hey there Caleb! Both the 2 inch and 2-5/16 inch balls supplied with the #WS97WR (adjustable 8" drop) fall under the same 22,000-lb hitch rating. Just make sure the ball matches your trailer coupler size, and always go by the lowest-rated part…
Hey McClaskey, since that is a rarer wheel bolt pattern we don't have any aluminum wheel options that match what you need. Instead our best option would be the Kenda Karrier #KR53 part #KE42EV which is a silver steel wheel with a ST205/75-15 tire…
Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
Hey David, welcome back. To add a 4-way connector to your 2025 Kia Sportage PHEV, you'll want the Curt item #C99DR. It connects directly behind the rear tail lights and there isn't a way to connect it to a tow package. It will not control a…
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
I do have a potential solution for you, but I do not have a 7 way harness that will plug in to the round plugs you described. I recommend using a pre-wired connector like part #20023. You will have to do a bit of cutting and splicing, and this kit…
It depends on what the brake controller output is set to. If you have the brake controller set to the maximum then there should be about 12 volts at the brake magnets. To see if the brake magnets are drawing the correct power set the brake controller…
The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…
Hello Robert, Thank you so much for attaching the pictures, they’re always so helpful. In the first photo, it looks like your shackle straps are sitting a bit too vertically. That’s not a major issue, but since you’ll be replacing some suspension…
Hey there Caleb! Both the 2 inch and 2-5/16 inch balls supplied with the #WS97WR (adjustable 8" drop) fall under the same 22,000-lb hitch rating. Just make sure the ball matches your trailer coupler size, and always go by the lowest-rated part…
Hey McClaskey, since that is a rarer wheel bolt pattern we don't have any aluminum wheel options that match what you need. Instead our best option would be the Kenda Karrier #KR53 part #KE42EV which is a silver steel wheel with a ST205/75-15 tire…
Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…
Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…
That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
The Curt front hitch part #31199 is a fit for your 2WD 2004 Nissan Titan. If you check out the install picture I attached you will see that it does not extend out past the front bumper of a vehicle it is installed on.
Hey David, welcome back. To add a 4-way connector to your 2025 Kia Sportage PHEV, you'll want the Curt item #C99DR. It connects directly behind the rear tail lights and there isn't a way to connect it to a tow package. It will not control a…
It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…
I do have a potential solution for you, but I do not have a 7 way harness that will plug in to the round plugs you described. I recommend using a pre-wired connector like part #20023. You will have to do a bit of cutting and splicing, and this kit…
It depends on what the brake controller output is set to. If you have the brake controller set to the maximum then there should be about 12 volts at the brake magnets. To see if the brake magnets are drawing the correct power set the brake controller…
The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Wire protection is essential for ensuring the safety and longevity of your electrical projects. Whether you're rewiring a trailer or securing connections, these products offer robust solutions for clamping, holding, and sealing wires effectively.
Wire protection is crucial for trailer rewiring, providing a secure seal that prevents electrical issues. Products like shrink tubing ensure watertight connections, enhancing the durability and safety of your trailer's wiring system.
Yes, wire protection products are versatile and can accommodate various wire gauges, such as 14-10 gauge wires. This flexibility makes them ideal for covering splices and ensuring a neat, secure installation.
Using wire protection in electrical projects offers several benefits, including preventing electrical shorts, protecting against environmental damage, and ensuring a clean, professional finish. This leads to fewer maintenance issues and a longer lifespan for your wiring.
Wire protection improves safety by creating a barrier against moisture and contaminants, reducing the risk of corrosion and electrical shorts. This is especially important in outdoor or exposed environments, where connections are more vulnerable.
Absolutely! Wire protection products are designed for easy installation, making them perfect for DIY enthusiasts. With straightforward application methods, such as heat shrinking, you can achieve professional results without specialized tools.
Filters
