Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 11-3/4" Long - 3,500 lbs

See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Recommended Ball Mount for a 2010 Toyota RAV4 With Factory Towing Package
  For your 2010 Toyota RAV4 Factory Hitch, you'll want about a 3 inch rise. You can confirm this by measuring from the ground to the top of the trailer hitch, and measuring from the ground to the bottom of the coupler. Then, subtract the higher number from the lower number. It does sound like you've gotten this about right though. If yours is a 1-1/4 inch hitch, I recommend the Draw-Tite Drawbar, part # 36063. This will give you a correct, 3 inch rise with a 3/4 inch ball hole diameter....
  view full answer...
• Trailer Hitch Recommendations for a 2008 Buick Lucerne Base Model, Special Edition, or Super
  In order to determine if your 2008 Buick Lucerne is a standard model CXL or a special edition, there are a couple of things you can do. If the driver seat is a power memory seat that remembers your settings and your tires are size 245/50R18, then you have a special edition. But the definitive way to determine the trim level of your Lucerne is to contact a local dealer and have them run the VIN number of the car and they will be able to tell you for sure which one you have. The Curt Trailer...
  view full answer...
• Drawbar included with Hidden hitch, part # 90139
  The drawbar that is included with Hidden Hitch, part # 90139 (no longer available), is Class II Drawbar 3-1/8" Rise (Kit), part # 36063. It fits 1-1/4 inch, Class II hitch receivers.
  view full answer...
• Ball Mount Recommendation For Class ll Hitch On 1996 Buick Estate Wagon
  One of the drawbars we offer for a Class ll hitch that fits a 1996 Buick Estate Wagon hitch is the Draw-Tite Ball Mount, part # 36063. This ball mount fits a 1-1/4 inch receiver opening and uses a hitch ball that has a 3/4 inch shank. This ball mount has a 3-1/8 inch rise from the top of the receiver tube. The hitch ball I recommend is part # 19258. This is a 2 inch ball with a 3/4 inch shank diameter.
  view full answer...
• Trailer Hitch and Wiring for a 1996 Buick Roadmaster
  We have a class II hitch that will fit your 96 Buick Roadmaster. The Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" Item # C12009. We haven't had the chance to install this hitch on a vehicle, but it is rated for a 50 minute install and has some drilling required. You can see the installation steps in the instructions I have linked. This Class II hitch is the only option for your vehicle so provided that its 3,500 pound capacity as well as the car's capacity are high enough...
  view full answer...
  
• Using a 36078 Class II Drop Drawbar as a Rise Instead of a Drop
  The drawbar you mentioned is not intended to be used in the rise position and would only create a 3-1/2 inch rise. We do carry a 5 inch and a 3-1/8 inch rise drawbar (see links below) that will fit the Class II hitch. These drawbars all have a tongue weight capacity of 300 lbs and a towing capacity of 3500 lbs. Keep in mind that if you need a significantly higher or lower drawbar to tow (you are not able to use the manufacturer's recommended drawbar for the hitch), you will void the manufacturer's...
  view full answer...
• Recommended Ball Mount Compatible With 1998 Cadillac DeVille
  Based on the confirmed fit trailer hitch receivers we have for your 1998 Cadillac DeVille, I assume you have a 1-1/4 inch receiver opening. Because of how far back this sits from the bumper, I recommend the Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 11-3/4" Long - 3,500 lbs # 36063. With this ball mount you can use # 19258 for a 2 inch hitch ball or # 19257 for a 1-7/8 inch ball.
  view full answer...
• Can a Trailer Hitch Be Installed on a 1997 Mercury Sable by a Mechanic
  I recommend the Curt Class II 1-1/4 Inch Hitch, part # C12232, for your 1997 Mercury Sable. This hitch has a maximum gross trailer weight capacity of 3,500 lbs and a tongue weight capacity of 300 lbs. You will need the recommended ball mount, part # C45522 and will also need a hitch ball like the Tow Ready 2 Inch Hitch Ball, part # 19258, For a wiring harness, you will use the # C55343 if you have a Wagon and # HM40565 if you have a sedan. I am including a link to the installation instructions...
  view full answer...
• Correct Ball Mount for a 1995 Buick Riviera
  I am not sure which draw bar you have, but the recommended draw bar for your vehicle and trailer hitch is the Class II Draw bar 3-1/8 inch Rise, part # 36061. None of the hitches or draw bars we carry have tapered receivers or shanks, so the only thing I can think of is that you have a Class 1 hitch and a Class 2 draw bar which are not compatible with each other even though they have the same 1-1/4 inch by 1-1/4 inch shank. . The Class 2 shank will not fit in a Class 1 hitch, but a class...
  view full answer...
• What is the recommended Draw Bar for a 1999 Cadillac DeVille
  The manufacturer recommended drawbar for your Cadillac DeVille is part number 36063 which has a 3-1/8 inch rise and 11-3/4 inch long distance between the center of the hitch pin hole and the center of the ball mount hole. When towing with a class II trailer hitch, the ball mount that is recommended by the manufacturer should be used. All class II trailer hitches are tested and rated with the specific ball mount for that hitch. Using a ball mount that is not recommended by the manufacturer...
  view full answer...
• Do I Modify My Auto Level Housing to Install a Draw-Tite Hitch # 36309 on my 2000 Buick Le Sabre
  In order to install this Draw-Tite Receiver Hitch, part # 36309, you will need to remove the rearmost fastener which secures the load leveling control housing to the frame rail and discard it. You will then trim the load leveling control housing around where the previously removed fastener was. See the picture to the right for further clarification. Some other items you may need: Draw Bar # 36063 Ball # 19258 or 19256 Trailer Wiring # 119176KIT
  view full answer...
  
• What is the Longest 1-1/4 Hitch Ball Mount You Carry?
  Since you mentioned the Draw-Tite Drawbar - 11-3/4" Long # 36063 and it is only compatible with Class II 1-1/4", it sounds like you have a Class II 1-1/4" hitch. If this is the case, we actually have a longer ball mount available. That is the Curt Class II Drawbar # C45000. This mount measures 13-1/2" from center of hitch pin hole to center of ball hole. If you by chance need a Class I 1-1/4" compatible mount, the longest one we carry is the Curt Class I Drawbar # C45025. This mount measures...
  view full answer...
• Ball Mount Recommendation for Hitch for a 1996 Lincoln Town Car
  The hitch part # 36116 is a Class II hitch that has the part # 36063 as the recommended ball mount which has a 3-1/8 inch rise. If there was a Class II hitch compatible ball mount that had a 3-1/4 inch rise available you could use it, but we do not carry one. That being said, the difference between the two sizes would not be hardly noticeable so the 3-1/8 should work just fine. For a 2 inch ball you would need part # 19258, or for a 1-7/8 inch ball part # 19257.
  view full answer...
• Ball Mount with at Least 3 Inches of Drop that is Longer Than 9-3/8 Inches Long for Old Rat Trike
  Ball mount # 36063 does have to be used in the rise position only. How about ball mount # 3592. It has a drop of 2-3/4 inches and measures 9-3/4 inches from the center of the hitch pin hole to the center of the ball hole. It is designed for Class I or II hitches. This is going to be the best option out of the ball mounts we carry.
  view full answer...
• Can Appearance Panel be Trimmed and Reinstalled After Hitch Installation on 2003 Lincoln Town Car
  A lot of vehicles have those body or appearance panels. On the 2003 Lincoln Town Car it is not structural meaning that it isn't there to help hold the bumper or fascia up. It is basically helping to protect the metal parts above it from the elements. You might be able to reinstall the panel but it would require some extensive trimming and there aren't specific instructions that explain how to do so. Leaving it off is the way I would go. I have linked a video and the instructions to the...
  view full answer...
• Recommended Equipment for Towing a Small Trailer with a Chrysler LHS
  We offer a Class II hitch, part number 36170, available for your vehicle. The hitch is rated to tow 3,500 lbs and has a tongue weight capacity of 300 lbs. I would recommend checking the gross weight of the trailer, with it fully loaded to find your tongue weight. If your weight is under 300 lbs, then this hitch will accommodate your trailer application. You will also need the ballmount, part # 36063 and the 2 inch Ball, part # 19258, as well as a pin and clip, part # PC2 or a hitch lock,...
  view full answer...
• Recommend Hitch and Wiring For 1997 Toyota Tacoma
  I do have an option for you but the Curt Trailer Hitch Receiver part # C12130 is designed to fit certain years of the Lincoln Town Cars and Mercury Grand Marquis so it will not fit the Toyota. The part # 36063 the sticker references is a ball mount that is recommended for use with the hitch determined by Draw-Tite. For a 1997 Toyota Tacoma, I recommend Curt Trailer Hitch Receiver part # 13013 which is a custom fit design for the Toyota Tacoma that will not require any drilling to install....
  view full answer...
  
• Does Draw Tite Trailer Hitch 41116 Fit 1999 Mercury Grand Marquis
  The Draw Tite hitch part # 41116 is a confirmed fit for your 1996 Mercury Grand Marquis. For a ball mount you'd need the part # 36063, for a 1-7/8 inch hitch ball part # 19257, for 2 inch ball part # 19258, then for trailer wiring # C59236.
  view full answer...
• Availability of a Complete Towing Package for a 1994 Ford Taurus Wagon
  We do have a hitch package, item # C12232, for the Taurus Wagon. Along with the package you will need to select the recommended ball mount, part # 36063, and a properly sized hitch ball and the wiring for your trailer and vehicle. The drawbar accepts a 3/4 inch diameter shank hitch ball so either the Hitch Ball with 2 inch Diameter and Short Shank, 3,500 lbs GTW - Chrome, item # 19258, or the Hitch Ball with 1-7/8 inch Diameter and Medium Shank, 2,000 lbs GTW - Chrome, item # 19257, would...
  view full answer...
• Is Drilling Involved when Installing Trailer Hitch # C12130 on a 1983 to 2010 Ford Crown Victoria
  For the 1983 to 2010 Ford Crown Victoria, Sedan and Wagon, you will need to drill 4 holes in the frame in order to install Curt Trailer Hitch, # C12130. I have included a link to the installation details. Step 4 in the instructions explains the required drilling. I have also included a link to a video showing installation on a similar vehicle, a 1992 Lincoln Town Car. The main difference on the Town Car and other vehicles compatible with this hitch is that on the Town Car there are some...
  view full answer...
• What is the Difference Between 2008 Buick Lucerne Special and Super Models and Regular Models
  The Super and Special are trim and packages that the 2008 Buick Lucerne could come with. The CXL Special Edition will have a chrome grille and chrome clad 17 inch wheels and a badge on the trunk that indicates it is a Special model. The Super can be identified by a rear spoiler. If you have a Special or Super model, hitch # 36502 will fit. For a different model 2008 Buick Lucerne the comparable Draw-Tite hitch is # 36309. I have included a link to the installation instructions and a video...
  view full answer...
• Trailer Hitch Recommendation for a 1994 Buick Roadmaster Estate Wagon
  We have a class II hitch that will fit your 96 Buick Roadmaster, but not a class III. The Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" Item # C12009. We haven't had the chance to install this hitch on a vehicle, but it is rated for a 50 minute install and has some drilling required. You can see the installation steps in the instructions I have linked. This Class II hitch is the only option for your vehicle so provided that its 3,500 pound capacity as well as the car's...
  view full answer...
• Trailer Hitch for 1998 Cadillac DeVille to Allow Towing Small Utility Trailer
  We do offer one trailer hitch receiver for your 1998 Cadillac DeVille, part # 36267 from Draw-Tite. This is a 1-1/4-inch Class II hitch with 300-lb tongue weight and 3500-lb towing capacities. You will want to check your DeVille's owner's manual or speak to a local Cadillac dealership to confirm that the vehicle is rated to tow a trailer. It is possible that the hitch and car have different capacities, and when this is the case the lower-rated item determines the overall capacity for the...
  view full answer...
• Hitch Recommendation for a 1998 Oldsmobile 88
  The Draw-Tite Trailer Hitch Receiver # 36211 that you referenced is confirmed to fit your 1998 Oldsmobile 88. This hitch has capacities of 3,500 total trailer weight plus 300 lbs tongue weight, your trailer will need to weight less than this. Also, you need to check the owners manual of your vehicle as well to determine the capacities listed for your vehicle and be sure not to exceed the lower of the two ratings. To complete your towing setup you may also be interested in the following...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?