See what our Experts say about this Draw-Tite Hitch Pins and Clips

• Visibility of the Curt Class I Hitch on a 2009 Volvo S40
  We have not had a chance to install this hitch on a vehicle like your 2009 Volvo S40, but I spoke with my contact at Curt and he said the majority of this trailer hitch will not be visible. The top of the receiver will sit flush with the bottom of your bumper fascia. He did mention that you may be able to see the bottom part of the mounting arms that extend just past the crossbar on both sides. I have attached installation instructions for you to check out. If you plan on doing any light...
  view full answer...
  
• Can a 1-1/4 - 2 Adapter be Used to Safely Haul a Cargo Carrier with a 2015 Toyota Corolla
  The concept of a hitch adapter like the Brophy # HTAD is a good idea in theory but the problem with using one of those with a 1-1/4" hitch, like part # C11265 or # 24913 for your 2015 Toyota Corolla, is that it will reduce the weight capacity of your trailer hitch by 50%. Since those trailer hitches have a tongue weight rating of 200 lbs this means that the tongue weight will be reduced to 100 lbs. If you were to use all of this for the 24x59 Curt Cargo Carrier # C18151 you would only...
  view full answer...
• Recommended Trailer Hitch For 2008 Toyota Camry SE V6
  Yes, we do have a hitch that will fit your 2008 Toyota Camry SE V6, but the item you selected, Curt Trailer Hitch, part # 12343, will not fit the SE model of the Camry. I would recommend the Draw-Tite Trailer Hitch Receiver, part # 36416, which is a Class II 1-1/4 Inch Hitch. To complete your towing setup you may be interested in the following: Draw-Tite Ball Mount, part # 36071 1-7/8 Inch Hitch Ball, part # 19256 2 Inch Hitch Ball, part # 19258 Pin and Clip, part # PC2 T-One Vehicle Wiring...
  view full answer...
  
• 1-1/4" to 2" Trailer Hitch Adapter for Bike Rack on 2008 MazdaSPEED3
  We have exactly what you need, although technically the adapter will not turn the Class I hitch into a Class II hitch, it will simply give your 2008 MazdaSPEED3 a 2" receiver. The Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver with 5" Rise # HT5R will convert your Mazda's Class I, 1-1/4" receiver into a 2" receiver and will also give you 5" of rise. This adapter will also reduce your hitch capacity by 50 percent, so if you had the Draw-Tite # 24816 hitch, for example, its maximum tongue...
  view full answer...
• Should a Locking Hitch Pin be Purchased to Help Keep a Hitch Cover from Being Stolen
  A trailer hitch cover like the Rubber Hitch Cover # 22281 is not one that can be locked, but since it is a common piece it really isn't in too much danger of being stolen. However, if you you are looking at a hitch cover that is a little more unique, like the part # HTCC11805, then I do recommend going with a locking hitch pin like part # e98880 as opposed to a typical pin and clip like part # PC3. This will help to deter theft of your cover. Please note that the lock and clip/pin numbers...
  view full answer...
• Can a 2009 Pontiac Vibe Safely Tow a 1,500 Pound Boat Trailer
  Since you would be right at capacity I do recommend taking any measures feasible in lightening the load. That will make it that much easier on the vehicle. I do believe that properly equipped, the 2009 Pontiac Vibe will be fine towing the 1,500 pounds. Since you will not constantly be towing it up a steep ramp, and that aspect is only a small part of the journey, the Vibe should be just fine. For a trailer hitch, you can use # C12221 but it is for GT models. If you have a GT model then...
  view full answer...
• Trailer Hitch Recommendation for a 2010 Ford Fusion Sport with Dual Exhaust
  Yes, the Draw-Tite Trailer Hitch, # 24865, will fit on all models of the 2010 Ford Fusion including the sport with dual exhaust. This hitch installs exactly the same as Hidden Hitch Trailer Hitch, 60282, which has been discontinued, and we have pictures and a video of it installed on a 2010 Fusion with dual exhaust. I have provided a link to the video for reference. The recommended ball mount but for the Draw-Tite Hitch is # 3594. For a ball you can use # 19256 (1-7/8 inch diameter)...
  view full answer...
• Recommended Hitch Adapter For 2016 Toyota Prius V With Class l Trailer Hitch To Carry Bike Rack
  We do not have a trailer hitch designed to fit your 2016 Prius. As manufacturers design and make them available, we do add them to our website so our customers can order them. The tire chains I recommend for your 2016 Prius are the Glacier V-Trac Cable Snow Tire Chains, part # PW1030. These are made of low-carbon steel and are designed with a low profile that means a smoother ride. These also come with tensioning rings that help secure the chains on the vehicle. You will want to check...
  view full answer...
• Trailer Hitch, Accessories, and Wiring for a 2006 Suzuki Forenza
  Curt trailer hitch # C11481 will fit a 2004 to 2008 Suzuki Forenza so it will also fit your 2006. If you plan on doing any towing with this vehicle be sure to consult the owners manual to make sure it can tow and to determine the vehicle capacity. The correct ball mount is # C45521 and you can use pin and clip # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # 119178KIT. I have linked instructions for the wiring and the hitch for you.
  view full answer...
• P315 Conversion Bar for Swagman XP Bike Racks
  Part # P315 probably would not work with your hitch. My information shows that the only available hitches for your 2008 Kia Optima are Class I hitches and P139 is for Class II only. We do have another adapter that will work for a Class I hitch. It is part # HTAD and it will allow your Class I 1-1/4 hitch to accept 2 inch accessories. You will need part # PC2 to hold the adapter into your hitch, and if you do not already have one, part # PC3 to hold your bike rack to the adapter. Please...
  view full answer...
• Hitch Pin and Clip Recommendations for the MaxxTow Trailer Hitch Receiver Adapter
  Basically you have two options for hitch pin and clips. Either a locking pin and clip or a non-locking pin and clip for both the 1-1/4 inch portion of the MaxxTow MT70355 and the 2 inch portion. For the 1-1/4 inch pin and clips you would want either the Pin and Clip # PC2 or the locking version part # 7682. For the 2 inch portion you would want either the Pin and Clip part # PC3 or the locking version part # 7683.
  view full answer...
• Fit of Curt C98BR Class I Hitch on 2021 Mazda 3 Turbo Hatchback
  The Draw-Tite Class I hitch, part # 24984 is a fit for all models of the 2021 Mazda 3 according to Draw-Tite. Usually, the on the more sporty models of small cars, the dual exhaust can present a fit problem, but as you can see in the linked installation instructions as well as the provided photo, the hitch fits perfectly with a dual-exhaust equipped vehicle. The receiver tube is hard to see, so I've circled it in red. If you'll be using the hitch for light duty towing, you'll also need...
  view full answer...
  
• Can Curt C11368 Class I Hitch Be Removed From 2017 Kia Forte and Installed on 2020 Model
  The 2017 Kia Forte was the second to last model year of the 2nd generation Forte, while the 2020 is the second model year of the 3rd gen. There were enough changes in the structure of the vehicle from the 2nd to the 3rd gen that unfortunately your Curt # C11368 from your 2017 Forte will not work on your 2020 model. For the 2020 Forte sedan, I'd recommend the Curt # C55HR Class I hitch you'd looked at. As you can see in the photo I provided, once installed the # C55HR will be much more...
  view full answer...
  
• Replacement Pins for Reese 15K 5th Wheel Hitch 30049
  The Reese 15K 5th Wheel Hitch 30049 that you referenced is the same as the Reese 16K 5th Wheel Trailer Hitch part # RP30051 save for the head but they both use the same base, Reese Square Tube Slider for 5th Wheel Trailer Hitch part # RP30048. I am not sure which pins that you need but if you are referring to the ones that hold the base to the rails then you can use part # 6014 but if you are referring to the ones that hold the head to the base then you can use part # PC2 (2). Also, if...
  view full answer...
• What Cargo Carriers are Made in the USA
  We do have two carriers made in the USA. They are both enclosed carriers. They are very high quality, but they are much more expensive. We have the the LetsGoAero models # H00604 and # HGK819.
  view full answer...
• What is the Difference Between a Class I and Class II Ball Mount
  Class I Ball Mounts When towing with a Class I trailer hitch, the Class I ball mount that is recommended by the trailer hitch manufacturer should be used. All Class I trailer hitches are tested and rated with the specific ball mount for that hitch. Using a ball mount that is not recommended by the manufacturer will void the warranty. The features of a a Class I ball mount are: Has a 1-1/4 inch x 1-1/4 inch shank Class II ball mounts will not fit on Class I trailer hitches Held in place...
  view full answer...
• How Does B&W Trailer Hitch Mount to a 1975 Chevy 1-Ton Dually Pickup Truck
  On B&W trailer hitch # BWHDRH25122 the mounting brackets are oriented the same for all applications. The tabs point in but attach to the bottoms of the frame rails. The customer submitting photo appears to have some other component installed. The upper brackets in that picture are not part of the hitch assembly. They appear to be bumper brackets. Once installed the receiver should be right under the bottom of the bumper of very close especially since you have a stock bumper on your 1975...
  view full answer...
  
• Does Spare Tire have to be Relocated on 1997 Ford Econoline Conversion Van to Install Trailer Hitch
  I spoke with my contact at Draw-Tite and he stated that on trailer hitch # 75703 the spare tire will not have to be relocated to install the hitch. I have included a link to the installation instructions and a video from when we installed the hitch on a 1994 Ford van for you. You will have to lower the spare tire to install the hitch but once the hitch is in place you replace the spare tire under the van.
  view full answer...
• Trailer Hitch and Towing Equipment Suggested for 2022 Toyota Corolla
  Per the owner's manual, Toyota doesn't recommend towing with the 2022 Corolla nor do they recommend installing a hitch. We can't recommend anything that contradicts the owner's manual, but many folks install a hitch anyway. If you decide to do so anyway and keep the weight you tow to a minimum, you could install the Curt # C34UR hitch and use a lightweight utility trailer like # K2MMT4X6. The trailer itself only weighs about 300 lbs, and I'd personally have no qualms using such a trailer...
  view full answer...
• Can Hitch Pin for Class III Hitch Be Used in Class I or II Hitch
  You cannot. A Class I or II hitch needs a 1/2 inch diameter hitch pin, while a Class III hitch uses a 5/8 inch diameter pin. For a 1/2 inch hitch pin, use # PC2. A locking version would be part # e98879.
  view full answer...
• 7-Way Trailer Connector Recommendation for 2016 Subaru Outback
  I'd be happy to help you with that. You'd need to begin with a trailer taillight converter harness like part # 118467. How to proceed from there will depend on if your trailer is equipped with electric brakes. If it is not, all you'd need is the 4 pole to 7-way adapter, part # 37185 which would permanently install on the rear of the vehicle. The adapter plugs into the 4-pole provided by the # 118467 and has 3 additional wire leads. The white wire grounds to the vehicle frame or chassis....
  view full answer...
• Will a Draw-Tite Trailer Hitch Fit a 2012 Hyundai Elantra Touring
  If you have a 2012 Hyundai Elantra Touring Hatchback, the Draw-Tite Trailer Hitch, # 24844, will fit. I have included a link to the installation instructions for you. I have also included a link to all of the hitches that fit the Touring Hatchback model. If you plan on doing some towing, this is a Class I trailer hitch with a 2,000 pound gross trailer weight capacity and 200 pound tongue weight capacity. You will want to consult the vehicle owners manual to determine the towing capacities...
  view full answer...
• Trailer Hitch Installation Instructions for a 2002 Saturn SL Sedan
  I have included a link to the instructions for trailer hitch # C11181 for you to view. On a 2002 Saturn SL sedan there are 7 steps which you will see in the instructions, and I have listed here: 1a.) If vehicle is equipped with tie-down brackets and/or existing weldnuts, remove the brackets from inboard side of the frame rail by removing three M12 bolts, each side. Return tie-down brackets and bolts to vehicle owner for reinstallation if hitch is removed. 1b.) If vehicle is not equipped...
  view full answer...
• Trailer Hitch Available for 2016 Kia Forte Hatchback
  We do indeed offer a hitch for the 2016 Kia Forte Hatchback (A/K/A Kia Forte5). You'll need part # C11395. If you'll be doing some light duty towing with the hitch, you'll also need the # C39KR trailer wiring harness, a # C45521 ball mount, a # PC2 hitch pin and a # 19256 for a 1-7/8 or # 19258 for a 2 inch trailer ball.
  view full answer...
  

Do you have a question about this Hitch Pins and Clip?