See what our Experts say about this etrailer Accessories and Parts

• Replacement for Gear Box on Venture Landing Gear VMC940RB
  The correct replacement gear box for your Venture landing gear VMC940RB is part # LC276602. This features cast aluminum construction that will last longer than a composite gearbox like # RVLG-RDBOX which fits Ram brand landing gear model # RVLG-8000.
  view full answer...
  
• Can The Gearbox For The etrailer Landing Gear Set Be Mounted Horizontally
  The gearbox # RVLG-RDBOX for the Landing Gear Set w/ Handle # RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place match up perfectly for both positions (pictured below).
  view full answer...
  
• 5th Wheel Landing Gear Clicks and Won't Go Up or Down
  It sounds like the gearbox could be bad or possibly the motor, this could be easily confirmed by removing each of the components (gearbox/motor) and testing them separately. The gear boxes are luckily pretty standardized and not terribly expensive, the Replacement Gearbox part # RVLG-RDBOX is what I recommend. The motors are a bit more but equally standardized, I recommend the Replacement Motor part # LG-142178.
  view full answer...
• Are Replacement Parts for Atwood Landing Gear Available or Will Another Brand Fit
  The division at Atwood that handled the jacks and landing gear was sold off to Lippert so direct replacement parts are not available. But it is likely that the gear box and motor of another brand will still fit. And yes, the gear box and motor do just sort of hang there. Gear box # RVLG-RDBOX is one possible option. With it you can use motor # M1230. For the driver leg D shaft there were 3 possibilities for Atwood landing gear depending on which model it is (standard duty, heavy duty,...
  view full answer...
• Gear Ratio for Replacement Gearboxes For Landing Gears
  Hey Shawn, The etrailer # RVLG-RDBOX, Stromberg-Carlson # LG-179015, and Lippert # LC276602 are all the same exact part made by different manufacturers so they would all have a 3:1 gear ratio.
  view full answer...
• Compatible Replacement Gearbox for Venture Landing Gear
  The gearbox replacement I recommend for your Venture landing gear is the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies # LC276602. The Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear # RVLG-RDBOX you asked about is not a compatible fit.
  view full answer...
  
• Replacement Gearbox to Attach Landing Gear Motor on 2009 Carriage Cameo
  It sounds like what you need is a replacement gearbox such as # RVLG-RDBOX, which is the replacement for etrailer and Ram landing gear. It will help to know the manufacturer or model number of your gearbox to find the right fit, though I do recommend checking out Replacement Aluminum Gearbox # LG-179015, which is designed for use with Stromberg Carlson landing gear but also works with most other manufacturers including Atwood, Lippert, and Venture. I've added links to video reviews of...
  view full answer...
• Solution for Needing Replacement Landing Gear for 2013 Starcraft Travelstar 278 BHS w Atwood 71125
  Since Atwood is no longer in the landing gear business it is basically impossible (unfortunately) to get just a replacement leg. The part number that you gave me actually is a document that shows the various parts for Atwood landing gear, but nobody has information as to what those replacement parts are the equivalent of. Because of this I recommend replacing the landing gear on your 5th wheel trailer. This gives you some peace of mind that you won't have to replace any parts in the near...
  view full answer...
• How To Choose Correct Replacement Landing Gear Legs for 5th Wheel Trailer with Dual Motors
  In order to confirm the correct replacement landing gear leg for your trailer you'll need to take a few measurements, the first simply being the length of the outer tube. Then, you'll need to measure the distance between the weld stops either inside to inside or outside to outside. The weld stops are what keeps the brackets in position on the outer tube. The most common replacement has a 29-1/2" long outer tube with 15-1/2" weld stop spacing inside to inside or 17-1/2" outside to outside....
  view full answer...
• Replacement Gearbox For Landing Gear On 2004 Keystone Sprinter with Venture VMC940RB-064625
  The replacement gear box for the Venture landing gear on your 2004 Keystone Sprinter with manufacturer number of VMC940RB - 064625 is part # LC276602. The gear box part # RVLG-RDBOX fits Ram 5th wheel landing gear.
  view full answer...
• Replacement Gearbox for Atwood Landing Gear
  It sounds like you need a new gearbox for your Atwood landing gear. I recommend the all-aluminum Lippert gearbox # LC276602 which works as a replacement for most brands of landing gear including Atwood, Lippert, and Stromberg-Carlson. The gearbox # RVLG-RDBOX that you referenced is for etraier and Ram brands of landing gear.
  view full answer...
• Attaching Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear
  If you take a look at the accompanying photo, you can see the small round piece that your Landing Gear Set # RVLG-8000 will need to have in order to attach the Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear # RVLG-RDBOX. That part will be in between the square shaft and replacement gearbox and allow the two to attach.
  view full answer...
  
• Electric Landing Gear to Replace Atwood Manual Landing on 1997 Scamp 5th Wheel Trailer
  The Lippert Electric Landing Gear Set # LC333964 will work fine as a replacement for your worn out Atwood setup. The gearbox in this kit as well as the stand-alone replacements like # LC276602 are standardized. This gearbox part actually works with most brands of landing gear, including Atwood, Lippert, and Stromberg-Carlson. Just to make absolutely certain I did review your inquiry with Lippert and they said you're good to go with # LC333964.
  view full answer...
  
• Replacement Landing Gear Box for 2015 Jayco Pinnacle Fifth Wheel
  The Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear # RVLG-RDBOX that you referenced is designed to fit Ram and etrailer brand fifth wheel landing gear part # RVLG-8000. This is a really common set seen on trailers but the even more popular option would be the # LC276602 which fits the brands Atwood, Venture, Lippert, and Stromberg-Carlson. Most likely this would be the kit you'd want.
  view full answer...
• Troubleshooting Powered Trailer Jack That Will Lower But Not Raise
  First thing I'd check is make sure the battery on the trailer has a good charge and all of the wiring of the jack and switches are making solid connections. If a powered jack doesn't want to work properly it's very common that the issue is related to the battery or the wiring. Let me know if that checks out. Since we don't carry Atwood jacks any more we'll have to set you up with a new landing gear set.
  view full answer...
• Replacement Landing Gear Motor and Gear Box Needed for a 2004 Keystone Montana 2980
  I do have a solution for you, but unfortunately manufacturers don't keep that kind of information on file. You could try using a replacement gearbox like part # RVLG-RDBOX and the compatible motor # LC142178 that fits Ram jacks, but without knowing the manufacturer and part number it would just be a guess as to whether it is the correct part or not. What I recommend doing is going ahead and just replacing your whole landing gear setup. It might be getting close to time to do that anyways...
  view full answer...
  
• How To Attach a Motor to a Trailer with Dual Jacks
  In regards to landing gear legs, the motor is attached to the gear box which then mounts to the output shaft of the leg. The output shaft will need to have a half-moon shape like the Lippert Components 32" Lead 5th Wheel RV Landing Gear Leg part # LC179013 in order for this to work. If so you can use a gear box like the Replacement Gearbox part # RVLG-RDBOX to attach a motor. If you have a different type of leg then we likely don't have any way to attach a motor but a photo would also...
  view full answer...
• Does Mounting Hardware Come with Replacement Landing Gear Gear Box RVLG-RDBOX
  Mounting hardware does not come with the replacement gear box part # RVLG-RDBOX.
  view full answer...
• Can Trailer Landing Gear Box be Removed from Trailer with Jacks on Ground
  If you were to remove the landing gear box from the set like with part # RVLG-RDBOX the jack legs would not free-spin and lower themselves so you could remove the box with the jacks holding the weight of the trailer or not. We do not carry the cross shafts for this jack though.
  view full answer...
• Replacement Landing Gear Box for 2000 KZ Sportsmen 5th Wheel
  The Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear part # RVLG-RDBOX works on most landing gear sets like those from Ram, Venture, Lippert Etc. That said, I don't have any way to confirm for a particular trailer. The only set I am aware of that the gear box will not work with is select older models from Atwood.
  view full answer...
• Solution for Fulton Landing Gear with Broken Gear Box
  Strangely enough Fulton does not offer replacement landing gear boxes for the landing gear sets. You'd need to look into getting a new set like the Bulldog part # BD500162 which would fit and work well.
  view full answer...
• Gearbox on 5th Wheel Landing Gear Makes Noise During Operation
  Your gearbox for your 5th wheel landing gear, like part # RVLG-RDBOX, will make a bit of noise while you are operating it. However, if it is fairly old and the sound you are hearing is different than what it normally sounds like or if it is starting to rust then you will definitely need to replace it. If you need to replace it just let me know what brand and model number (if you know it) your 5th wheel landing gear is and I can recommend a replacement gearbox that is compatible.
  view full answer...
• Replacement Gearbox for Landing Gear on 2004 Keystone Cougar When D-Shaft Gear Is Too Small
  The Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear # LG-179015 will fit all Lippert, Atwood, and Stromberg Carlson landing gear. The Replacement Gearbox for etrailer and Ram 5th Wheel Landing Gear # RVLG-RDBOX will fit the Ram brand jacks. The brand of your landing gear should be printed on the legs somewhere and the Ram D-shaft is slightly larger than the Stromberg Carlson compatible brand.
  view full answer...
• Tube Size of etrailer Landing Gear RVLG-8000
  Landing Gear # RVLG-8000 has an outer tube dimension of 2-1/2 inches and inner tube dimension of 2-1/4 inches. The drive shaft diameter is 1/2" and uses motor # LC142178 which installs on gearbox # RVLG-RDBOX. I've added links to a couple review videos for you to take a look at as well.
  view full answer...

Do you have a question about this Accessories and Part?