See what our Experts say about this etrailer Trailer Jack

• US Made Swivel Side Mount Trailer Jack
  The etrailer brand # TJP-2002S-B is manufactured in China. We do offer some side mount trailer jacks from Dutton-Lainson that are manufactured in the USA. They don't offer a pipe mount jack, but they do offer a swivel pin mounted jack which would be much more stable. I'd recommend the part # DL22339 1700 lb capacity bolt-on jack. The jack also provides a caster to make maneuvering your trailer around while its being stored much easier. The jack is compatible with frame members that are...
  view full answer...
• Is Trailer Jack Capacity for Tongue Weight or Trailer Weight
  A trailer jack like the # TJP-2002S-B is designed to handle the tongue weight of the trailer and that is what the capacity is referencing. A trailer jack, just like a tow vehicle, only has to support the tongue weight since you also have wheels and tires on the ground supporting the trailer. You are correct, tongue weight is typically 15% of the loaded trailer weight. For a 645 lb tongue weight like yours you want a jack that can handle at least that much. This typically means it is overrated...
  view full answer...
• Parts Needed To Mount A Tube-Style Swivel Jack To A Trailer Frame
  To mount the Bulldog Round Jack without mount # 150010 to a trailer frame you would need to use weld on a female swivel pipe # TJP-OP916 to the jack. If you trailer doesn't have the male swivel pipe then you would need to weld part # DL22670 onto the frame as well. If you don't know how to weld or would prefer not to pay for someone else to do it then you can also just get a similar jack with the swivel components already attached like part # TJP-2002S-B.
  view full answer...
• Can Caster Wheel Be Added to Jack with Footplate
  It would be possible to cut off the footplate on jack # TJP-2002S-B but doing so would of course void the item's warranty. Also, the drilling of the two holes needed to install a caster wheel like # JC-101 would possibly weaken that inner jack tube. The problem is you cannot know by how much you will have reduced the jack capacity by this modification. Also, the caster wheels available do not have the same 3000-lb weight rating that the original footplate does. So even if the jack tube...
  view full answer...
• Pull Pin Diameter for Round, Pipe Mount Swivel Jack TJP-2002S-B
  The Round, Pipe Mount Swivel Jack w/ Footplate # TJP-2002S-B uses a 9/16" Diameter pull pin. Just like the replacement pull pin and chain # TJP-PN916. The hole on the mount is just over 9/16" so that the pin can fit. I attached a short review video of the Swivel Jack for you to check out.
  view full answer...
• Availability of Swivel Trailer Jack Similar to Whats Offered on Kendon Folding Motorcycle Trailer
  I looked up the trailer and jack you mentioned and wasn't able to find all the specifics about the jack. I did find that it's a pipe mount, and that the jack offers 10 inches of lift. I wasn't able to find its capacity. For a similar jack, I'd recommend the etrailer Sidewind Swivel Jack, part # TJP-2002S-B. This jack includes a footplate rather than a caster, and would cost less than half the jack they offer. What I couldn't see in their photos is exactly how the pipe mount attaches to...
  view full answer...
• Correct Replacement Handle for Ram Swivel Marine Trailer Jack
  The Replacement Sidewind Handle Knob for etrailer and Ram Swivel Marine Jacks part # MJ-1000B-KB is designed for Ram swivel marine jacks like the Round, Pipe Mount Swivel Jack part # TJP-2002S-B so if this is what you have it will work great. Unfortunately, we don't know what jack is installed on anyone particular trailer.
  view full answer...
• Trailer Jack and Winch for 3,000 Pounds or Less Boat Trailer
  Since a jack doesn't need to hold the weight of the entire trailer it's pretty easy to get one rated for more than what you need. the 1,500 pound bolt-on swivel jack # MJ-1500B-DWL or 2,000 pound weld-on # TJP-2002S-B will be enough and are both great options. It's the same for a winch as well. The winch doesn't need to support the entire weight of the boat but needs to be strong though to pull it along your rollers. Being that you have rollers that will make it easier on the winch...
  view full answer...
• Does Bulldog Jack Mount # BD015279 Fit etrailer.com Swivel Jack # TJP-2002S-B
  Yes, the Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount # BD015279 that you referenced is the correct dimensions to match the pipe mount of the etrailer.com trailer jack part # TJP-2002S-B that you also referenced.
  view full answer...
• Dimensions of Pipe Mount Swivel Jack # TJP-2002S-B from Pipe Mount to Gearbox
  For Pipe Mount Swivel Jack # TJP-2002S-B the distance from the center of the pipe mount up to the top of the gearbox is 6-1/2-inches. From the center of the pipe mount up to the highest point of the handle rotation the distance is 12-inches. Overall length from the foot plate to the top of the gearbox is 21-1/2-inches with the jack fully retracted. Additional dimensions are shown in the linked photo.
  view full answer...
  
• What is Overall Height of etrailer Jack # TJP-2002S-B
  The overall height of the trailer jack # TJP-2002S-B is 21-3/4 inches when fully retracted. When the pipe mount # BD500240 is welded to the trailer the jack will basically be flush up against the trailer frame so there wouldn't be any clearance there. Now the body of the hitch would be more like 3-1/2 inches away from the frame of the trailer though so if that's the clearance you are looking for this would work to fit past your 1-1/2 inch supports.
  view full answer...
• What Does Round, Pipe Mount Swivel Jack # TJP-2002S-B Weigh
  The Round, Pipe Mount Swivel Jack # TJP-2002S-B that you referenced weighs 14 lbs total and has a weight capacity of 2,000 lbs.
  view full answer...

Do you have a question about this Trailer Jack?