This swivel jack pivots up for travel and down for use. Built-in grease zerk allows for simple greasing. Retracted height is 10-1/4". Extended height is 20-7/8". Weld-on pipe mount included.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there. I'm Michael with etrailer.com. Today, we're gonna take a quick look at this round, pipe mount swivel jack with foot plate. This is gonna be a utility jack that will allow you to raise and lower your trailer. It has a lift capacity of 7,000 pounds and a support capacity, once you have it raised, it'll support up to 8,000 pounds. So, it is going to be ideal for your agricultural and commercial applications.
It has this tubular swivel design that's going to allow you to twist the jack up for storage, and then twist it down again for use to raise and lower. This does have a weld-on installation with this female pipe mount here. So, this will weld onto your trailer and you'll be able to slide the jack in like that, or you could remove it and just leave that female pipe fitting on there. And then of course, we do have our pull pin that's going to allow us to keep it in place. Whether we want in the vertical orientation or in the horizontal orientation, it's gonna make sure that it's gonna be nice, and snug, and secured in there for us.
And our pin does have this lanyard connection to make sure that it's not going to get lost while we're disconnect. As far as our pipe mount dimensions go, our inner pipe here does have a outer width of 2 1/2 inches, an inner width of two inches. And then our female or outer pipe here has an outer width of three inches. And then of course, a 2 1/2 inch inner width, so that that will slide right in place on that inner portion. This does have a top wind handle.
It's got this black claw grip. It's gonna be very comfortable and easy to crank our jack up. Our handle does have a radius of about 8 1/2 inches. So, not too large and it should give us enough leverage to raise and lower as needed even under weight. The bracket height here, when we have it fully retracted, we're going to be looking at 11 1/2 inches from the bottom of our foot plate to the center of our pipe.
And then when we have it fully extended, we're gonna have a 21 1/2 inch distance there. So, that's gonna give us a travel of 10 inches. Our foot plate is eight inches long by approximately six inches wide. When I measured it, it was 5 7/8 of an inch wide, so still plenty wide there. It helps to minimize sinking into soft ground. So, no matter the environment, you'll still have a nice, solid base there. This does have a durable black powder coat finish on our outer tube. And the inner tube and foot plate have a rust resistant, clear zinc finish. So, they are going to hold up well for us and give us plenty of corrosion resistance, help it to last a nice, long time. You can see here at the top, we do have this grease zerk built-in. So, it's gonna be very easy to hook up our grease gun, pump some grease in there, and make sure everything stays well lubricated, so that we're gonna have a nice, long-lasting jack here. So, if you are looking to replace or add a jack onto your trailer, this is gonna be a great option for you, especially if you don't mind welding that outer pipe in place, this will give you a nice, sturdy action and give you plenty of stability for your trailer. And that completes our look for today. Again, I'm Michael with etrailer.com. Thanks for watching..
Average Customer Rating: 4.9 out of 5 stars (186 Customer Reviews)
This swivel jack pivots up for travel and down for use. Built-in grease zerk allows for simple greasing. Retracted height is 10-1/4". Extended height is 20-7/8". Weld-on pipe mount included.Ordered 10 of these jacks for a project, and they arrived very quickly. They are replacements for a different brand, and seem to be very good quality and heavily built. Great price also I would order these again.
Easy to weld on and is not to difficult to jack a trailer up.
Hey Carol,
I bought this jack to replace one that was very similar to yours. I could have kicked myself for not doing it earlier. This trailer jack will lift more weight and it’s so much easier to move up and down. More weight easier to work its a great product. I would recommended this product to my friends and family.
Also I was upgraded on shipping thanks to Your great staff.
Thank you
Mike
Thank you
Mike
A quick and easy fix to my rusty, frozen jack! Fit directly on existing mount.
Worked well, like the large welding ring and grease fitting.
easy site..fast shipping
Review from a similar Ram Round Topwind in Trailer Jack
Exactly what I needed for our Message board trailers. Great Quality and the Snap Ring is thicker than other brands. I cut the old bracket off and welded on the new one.
Review from a similar Ram Round Topwind in Trailer Jack
We received 5 boxes with these jacks. Three of the 5 boxes were absolutely destroyed in shipping. None of the jacks were wrapped in any kind of package but the cardboard box they shipped in. Most of them have scratches on them. We did not pay for a used looking jack.
Review from a similar Ram Round Topwind in Trailer Jack
Does the job! Easy to install and functions without fault.
Review from a similar Ram Round Topwind in Trailer Jack
Arrived quickly. Fit on my trailer. Works great!
I particularly appreciated the information about the diameter of the swivel. I was able to replace my old jack without needing to change the mounting plate.
Review from a similar Ram Round Topwind in Trailer Jack
The only reason I didn’t give a five star is because only time will tell how the jacks hold up. Overall so far the jack looks like a good product.
Review from a similar Ram Round Topwind in Trailer Jack
Good inexpensive jack. I ordered two. My use for them is somewhat "off label". My 19" 9000# capacity flatbed trailer has a label on the dovetail indicating that the rear of the trailer should be supported for any loads over #3000. Personally I think supporting the rear for a trailer is always a good idea when loading and unloading. It puts less strain on the rear of the trailer and it prevents the trailer from lifting the rear of the tow vehicle during loading which can be extremely dangerous.
I had a friend weld the tube mounts on each side of the rear of the trailer. See pictures below. Now I don't need cribbing or chunks of wood to shove under the rear of the trailer. These will also adapt well to uneven ground. They can be stowed horizontally, like in the picture or removed when not needed.
Review from a similar Ram Round Topwind in Trailer Jack
Hard to find a good jack for my custom inherited trailer. Old one was too short and wouldn’t crank up or down. This one was perfect replacement.
Came with a welding bracket but I won’t use that since going on an existing trailer. Jack works great and just snapped right on. The pull release is solid and engages really well. I’m happy.
Review from a similar Ram Round Topwind in Trailer Jack
Good welds, nice finish, smooth action up and down. This jack has met my expectations initially.
Review from a similar Ram Round Topwind in Trailer Jack
A nice heavy duty jack that will serve me well. Great packaging and customer service is excellent. I plan on using this jack on my trailer that is made from an old model camper frame with an old model jack and large tongue frame. This trailer is used for hauling my side by side on hunting trips and for hauling my riding lawn mower. A+++++++
Review from a similar Ram Round Topwind in Trailer Jack
This was a perfect replacement for a prior jack that had bent and no longer fully retracted. An excellent value! It works perfectly to raiser, lower, and support an 1,800 lb trailer. I also appreciate the zerk fitting for easy greasing.
Review from a similar Ram Round Topwind in Trailer Jack
We bought this jack for a very small MC pop up trailer. Fits as described. Shipping was fast and the quality is impressive. Very sturdy. Still building so we have not tried it under more than 350lb. load. So far so good.
Review from a similar Ram Round Topwind in Trailer Jack
Jack was easy to install and videos provided were helpful.
Jack was much heavier than I thought and seems to be well constructed.
Just what I needed for my narrow frame/tongue.
Review from a similar Ram Round Topwind in Trailer Jack
I've used it a couple of times on the trailer out camping. Otherwise it is in constant use when the trailer is parked in the garage. Seems to work fine.
Do you have a question about this Trailer Jack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.