See what our Experts say about this etrailer Trailer Jack

• Replacement Parts Available for the RAM Trailer Jack Part # TJD-7000S
  I do have several replacement parts available for the RAM Trailer Jack part # TJD-7000S but not an all inclusive rebuild kit. Instead you will need to select from the components listed below and repair the jack as needed. The most common fault on the above trailer jack is the spider gears and in order to replace them you will want to use part # TJD-7000S-GR. The rest of the replacement parts we have for the jack are listed below. If you can identify what is not working on the jack I would...
  view full answer...
• Trailer Jack Solution for Trailer Tongue that is 6 inch by 3 inch
  That is a pretty tall trailer frame but we do have a solution Dan. You could use the part # HD50000101 unless you wanted a swivel option. Then I would go with a weld on style jack like the etrailer # TJD-7000S for a sidewind or the part # TJD-8000 for a top wind. Or if you wanted something that could swivel you'd want a pipe mount like the part # BD178203.
  view full answer...
• Recommended Keeper Pins for RAM 7000 and 5000 Series Jacks
  Hey Kelly, I went ahead and checked out all of those jacks and I believe I was able to find what you're looking for. So, for # TJDP-7000-B, # TJD-7000, # TJD-7000S, and # TJDP-7000S-B, you can use the Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-PN; and for # TJD-5000 and # TJD-5000S you can use the Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks # TJP-PN58.
  view full answer...
• Recommended Replacement Handle and Pin for a RAM 8000 Series Jack
  For your RAM 8000 Series jack # TJD-7000S, you can use the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks # TJD-7000S-HD for a replacement handle and handle pin. If by pin you were actually referring to the footplate keeper pin, then you'd need the Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-PN as well.
  view full answer...
• Will Drop Leg from Ram 7000 Series Jack Fit a Ram 8000 Series Jack
  If you are talking about the drop leg # TJD-7000-FT then it could fit your 8000 series jack as long as all the measurements match up. This jack is 2 inches square and the distance from the center of one adjustment hole to the center of the next is 3-3/8 inches.
  view full answer...
  
• Diameter Of Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks
  I went to the warehouse and took a measurement of the Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks, part # TJD-7000S-HD. The handle diameter is 1/2-inch. I have attached a photo of the handle with the dimension shown you can check out.
  view full answer...
  
• Gear Kit for Ram 8000 Series Trailer Jack
  The 8000 Series jack is # TJD-7000S. The replacement gear kit is # TJD-7000S-GR. If you'd like to verify you can measure the gears on your jack. The small gear is 1.331 inches for the outer diameter and 0.505 inches for the inner. Then the large gear is 1.703 inches outer and 0.595 inches inner./
  view full answer...
  
• Solution for Ram 8000 Series Trailer Jack that Won't Crank Up or Down
  Sounds like you need a gear kit to fix your Ram 8000 series trailer jack as yours are damaged. For that we have the # TJD-7000S-GR. When the Ram 8000 jack has the issue you described it is due to damaged gears which is what this kit fixes.
  view full answer...
• What is Difference Between etrailer # TJD-8000S and # TJD-7000S Trailer Jacks
  The big difference is the orientation of the foot plate on both jacks. One just has the rectangular shaped foot plate rotated 90 degrees from the other. Aside from that they both have the same capacities and travel.
  view full answer...
• Using Weight Distribution Hitch on Trailer with Side-Frame-Mount Jack
  In order to use a weight distribution/sway control (WD/SC) system it is necessary to have room on the trailer A-frame to mount the spring bar lift brackets and the hitch on the tow vehicle must specifically be rated for use with WD/SC systems. The hitch safety sticker will indicate if it is indeed rated for use with WD. As for the jack, it sounds like you have a side-frame-mount jack like # FXPD15L or one of the similar jacks of this type shown on the linked page. Some of these, like...
  view full answer...
• Installation Instructions for Square Direct Weld Jack # TJD-7000S
  I am attaching a picture of the instructions for your application to the product page. The instructions say to put the jack in the proper location for your trailer application, then weld on both sides of the jack length using a 3/16 inch fillet weld.
  view full answer...
  
• Replacement Bushing For Etrailer.com Weld On Square Direct Weld Jack w/ Footplate
  I am happy to help you out. We do have the replacement bushing you are asking about for your Square Direct Weld Jack w/ Footplate, # TJD-7000S. That replacement bushing is part # TJD-7000S-BU.
  view full answer...
• Weld On Pipe Mount for Trailer Jack # TJD-7000S to Fit 2 inch Male Fitting
  For a 2 inch pipe mount to fit over a 2 inch male pipe on your trailer you could weld the part # BD015271 to the jack part # TJD-7000S.
  view full answer...
• Replacement Handles for Ram Jacks
  It sounds like you have the RM0708DLJK Ram jacks which are very similar to the # TJD-7000S. You can use the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks # TJD-7000S-HD as a replacement handle for your jacks.
  view full answer...
• Is Replacement Internal Screw Available for Ram 7K Weld-On trailer Jack
  I spoke with my contact at Ram and they said that the internal screw for the 7K jacks are not something they carry replacements of so you will need to replace the whole jack. Even if this wasn't the case it would be a good idea to replace the entire unit anyways so that you can be confident all of the internal components are working properly. From what you described it looks like you either need part # TJD-7000S which is a weld-on 7K jack with a sidewind handle or part # TJD-7000 which...
  view full answer...
• Does Replacement Bearing for etrailer Jack
  The Replacement Bearing for etrailer and Ram Square Jacks - 7,000 lbs # TJD-7000-BR is 1/2 inch; it is does not have a weight capacity itself, but is designed specifically as a replacement for the following 7,000 lb etrailer and Ram jacks: - Square Direct Weld Jack with Footplate - Drop Leg - Topwind - 28-3/4" Lift - 7,000 lbs # TJD-7000 - Square Direct Weld Jack with Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs # TJD-7000S - Square Pipe Mount Swivel Jack with Footplate...
  view full answer...
• Weld-on 7,000 Pound Trailer Jack with Weld Mount Already Installed
  The Square Direct Weld Jack # TJD-7000S does not include a mount and is designed to be welded directly to your trailer. For a similar jack the Square Pipe Mount Swivel Jack # TJDP-7000S-B installs using a weld-on pipe mount. It meets the same 7,000 pound capacity and has 15 inches of travel.
  view full answer...
• Replacement Handle and Gears for the Square Direct Weld Jack w/ Footplate Part # TJD-7000S
  If you are referring to the Square Direct Weld Jack w/ Footplate part # TJD-7000S then the correct replacement handle is the Replacement Sidewind Handle part # TJD-7000S-HD and the correct replacement gear kit is the Replacement Sidewind Gear Kit part # TJD-7000S-GR. If the above is not the jack you are referring to then please let me know the make and model and I will see if we have any replacements parts for this assuming it is a brand we carry.
  view full answer...
• Replacement Lower Bushing And Washer For The Ram TJD-7000S Jack
  The Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs Item # TJD-7000S-GR has the replacement pins in the kit. The washer can just be replaced with any washer that will fit over the shaft. You just want to make sure it is the same thickness as the bent washer. As far as the tube shaft bushing under the horizontal gear, unfortunately we do not currently offer that replacement part. It would require replacing the jack. I recommend going with...
  view full answer...
• Replacement for Ram Square Direct Weld Jack
  The replacement cap for the Square Direct Weld Jack w/ Footplate - Drop Leg - Sidewind - 28-7/8" Lift - 7,000 lbs # TJD-7000S is the Replacement Cap for etrailer and Ram Square, Sidewind Jacks # TJD-7000S-CP.
  view full answer...
• Trailer Jack Recommendation for Needing Trailer 32 inches Above Ground
  Best solution would be the etrailer jack part # TJD-7000S as it can lift up to 28-7/8 inches and since it's a weld on style jack without any hardware you could attach it at the height you need to get the addition 3-1/8 inches you'd need as well.
  view full answer...
• Can Footplate be Rotated on etrailer.com Square Direct Weld Jack
  Yes, the footplate for the Square Direct Weld Jack # TJD-7000S can be oriented so that the wider section is facing either way for your trailer. There are holes in both directions for the jack itself that allow you to do this. I am attaching both pictures that you referenced as well as a review video that you can check out where this feature is highlighted.
  view full answer...
  
• Availability Of Replacement Gear Kit For Ram 2500 Series Side Mount Trailer Jack
  I reached out to my contact at Ram and he was able to confirm that the correct replacement gear kit for your Ram 2500 Series Side Mount Trailer Jack is the Replacement Sidewind Gear Kit for etrailer and Ram Square, Direct Weld Jacks - 5,000 or 7,000 lbs # TJD-7000S-GR. I included a video of the # TJD-7000S-GR for you to take a look at.
  view full answer...
• Replacement Jack for 2007 Trailmaster Trailer Vanguard
  We don't have replacement gear kits for the jack you have based on looking at the picture you submitted so our best option would be a new jack like the part # TJD-7000S which you could weld in place of your current jack once it has been removed.
  view full answer...