Pull Pin Diameter for Round, Pipe Mount Swivel Jack TJP-2002S-B

Question

Question:

What size is the pin hole on this model?

asked by: Bobby

0

Expert Reply:

The Round, Pipe Mount Swivel Jack w/ Footplate # TJP-2002S-B uses a 9/16" Diameter pull pin. Just like the replacement pull pin and chain # TJP-PN916.

The hole on the mount is just over 9/16" so that the pin can fit. I attached a short review video of the Swivel Jack for you to check out.

expert reply by: Robert C

0

Answer 1

I looked up the trailer and jack you mentioned and wasn't able to find all the specifics about the jack. I did find that it's a pipe mount, and that the jack offers 10 inches of lift. I wasn't able to find its capacity. For a similar…

view full answer...

Answer 2

The mounting holes are 3 inches apart on center for the Round Snap Ring Swivel Jack w/ Footplate - Weld On - Sidewind - 14-1/2" Travel - 2,000 lbs #TJB-2002S-B. The head is 2-1/2 inches square for this jack as well.

view full answer...

Answer 3

The snap ring, part #SNP-RING that holds the etrailer sidewind jack, part #TJB-2002S-B measures 2-inches diameter. If that is the diameter of the snap ring you need for your trailer jack it may work but there is no guarantee since it is designed for…

view full answer...

Answer 4

The Replacement Retaining Ring #SNP-RING measures 0.08 inches, but keep in mind there will be some slight variances on a per-ring basis. This is a replacement for specific jacks, which are the following Ram/etrailer jacks: TJB-2002-S, #TJB-2002S-B,…

view full answer...

Answer 5

Yes, the Bulldog 2-1/4" Long, Weld-On Jack Pipe Mount #BD015279 that you referenced is the correct dimensions to match the pipe mount of the etrailer.com trailer jack part #TJP-2002S-B that you also referenced.

view full answer...

Answer 6

Fulton's snap-ring jacks like the #FTJ120W0301 are going to top out at 1,200lbs and the 1,500LB Jack #F141132 you found has a bolt-thru design and is not offered in a snap ring. We do offer the 2,000LB Jack #TJB-2002S-B which would fit your…

view full answer...

Answer 7

Round Snap Ring Swivel Jack w/ Footplate - Weld On - Sidewind - 14-1/2" Travel - 2,000 lbs Item #TJB-2002S-B weighs about 15 pounds with a shipping weight of 16 pounds.

view full answer...

Answer 8

The inside diameter of the snap ring that would be used for the #TJB-2002-B is 2 inches, and the outside diameter is 2-1/4 inches. We offer the replacement snap ring for that jack as part #SNP-RING

view full answer...

Answer 9

For your Down To Earth Trailer, I recommend the Round Snap Ring Swivel Jack w/ Footplate part #TJB-2002-B. This jack uses a snap ring swivel bracket with a 2-1/2" outer diameter. It should work with the existing bracket you have on your trailer…

view full answer...

Answer 10

Hey Dan. If your jack mount has a 2-1/2" ring on it then the Round Snap Ring Swivel Jack w/ Footplate item #TJB-2002S-B is going to be your best option. This 2,000 lbs capacity jack attaches to the same size bracket that the Fulton item…

view full answer...

Answer 11

From the center of the main mounting section of the Round Snap Ring Swivel Jack #TJB-2002-B to the top of the handle part that connects to the jack is about 5-1/2". The handle then dips down about 1-1/4" while the handle grip sits about…

view full answer...

Answer 12

I went to our warehouse to provide you a few measurements of the Pro Series pipe mount swivel jack #PS1401080303. The length of the entire swivel jack in the retracted position is 26-3/4 inches. The foot plate is 3-3/4 inches wide and 7-1/2 inches…

view full answer...

Pull Pin Diameter for Round, Pipe Mount Swivel Jack TJP-2002S-B

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching