See what our Experts say about this etrailer Trailer Jack

• Does etrailer Bolt-On Swivel Mounting Plate Fit Jack TJP-5001S-B
  Hey there Gary, thanks for the photo and yes the etrailer Bolt-On Swivel Mounting Plate for 3,500-lb Trailer Jacks with a 5/8" Swivel Pin # e52JR will indeed work with your Round, Pipe Mount Swivel Jack # TJP-5001S-B.
  view full answer...
• Replacement Zerk Fitting for etrailer Jack # TJP-5001S-B
  We actually have a replacement zerk fitting for all of the etrailer/Ram trailer jacks with the part # Gzerk. This is a standard 1/4 inch pipe thread.
  view full answer...
• Weld-On Pipe Mount For The TJP-5001S-B Round Pipe Mount Swivel Jack
  We have just the thing! The Replacement Male Pipe # TJP-IP916 is going to be the correct weld-on male pipe mount for the # TJP-5001S-B jacks. If you need the female side to weld to the jack itself it will be part # TJP-OP916.
  view full answer...
• Length of Pipe of Round, Pipe Mount Swivel Jack TJP-5001S-B
  The length of the pipe itself (the round mount) is 2-1/4 inches for the Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 10" Travel - 3,000 lbs # TJP-5001S-B. I can't tell you for certain though whether it is long enough to mount to a 3.5 inch steel I-beam and be able to clear it when connected or swiveled. I have added a link below to a video review for you to check out as well if you'd like to take a look.
  view full answer...
• Dimensions For Round, Pipe Mount Swivel Jack # TJP-5001S-B
  There is roughly 1/2" of exposed inner tube on the Round, Pipe Mount Swivel Jack # TJP-5001S-B exposed the bottom of the outer tube. This will give you a length of 9-3/4" from the center of the pipe mount to the bottom of the tube.
  view full answer...
  
• Replacement Mount for etrailer Round, Pipe Mount Swivel Jack
  The correct replacement male pipe mount for the Round, Pipe Mount Swivel Jack part # TJP-5001S-B is the Round, Pipe Mount Swivel Jack part # TJP-IP916.
  view full answer...
• Dimensions and Pin Size For Round, Pipe Mount Swivel Jack # TJP-5001S-B
  The Round, Pipe Mount Swivel Jack # TJP-5001S-B uses a 5/8" Diameter Pull Pin # TJP-PN58. The jack slides onto a 2" diameter weld on pipe that is included.
  view full answer...
  
• Total Height of Round, Pipe Mount Swivel Jack # TJP-5001S-B
  The overall height of the Round, Pipe Mount Swivel Jack # TJP-5001S-B is 16-3/4 inches when fully retracted and 26-3/4 inches when extended. Basically from the center of the pipe mount to the top of the jack measures 6-1/2 inches.
  view full answer...
  
• Does the Footplate on etrailer 3K Trailer Jack TJP-5001S-B Spin when Handle is Cranked
  I went out to the warehouse to test the Round, Pipe Mount Swivel Jack w/ Footplate - Weld On - Sidewind - 10" Travel - 3,000 lbs Item # TJP-5001S-B for you. When cranking the handle the footplate does not spin. Going from cranking the leg from one direction to the other causes the footplate to shift a little but it does not continue to spin. I have linked a video review of this jack for you.
  view full answer...
• Can The Round Pipe Mount Swivel Jack TJP-5001S-B Be Operated By A Power Drill?
  Hello Evan, thanks for reaching out. Sadly, the Round, Pipe Mount Swivel Jack # TJP-5001S-B does not have any kind of provision for operating with a drill. For that jack it will be the hand crank only. If you are looking for a jack that can be operated by a drill take a look at the Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate # TV64FR. This has a 5,000 lb capacity and includes an adapter that allows the jack to be used with a cordless non-impact drill.
  view full answer...

Do you have a question about this Trailer Jack?